Santosh Kumar Pitla
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Santosh Kumar Pitla has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Andrew Donesky
1 shared publicationCarol J. Thompson
Animal Science Department, University of Nebraska, Lincoln, NE
1 shared publicationCheeTown Liew
1 shared publicationIan Tempelmeyer
1 shared publicationJames Bw Roeber
1 shared publicationJared Werner
1 shared publication
Latest Publications
- 1 January 2023
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Journal of the ASABE
- Vol. 66 (6) , 1481-1496
Estimating Battery Size Requirements for Tractor Electrification of Row-Crop Planting Operations
Highlights Calculate and compare engine power needed for row-crop planting from ASAE standards and reported CAN data. Estimate energy requirements and the equivalent electric battery’s volume and mass for row-crop tractor. Discuss the feasibility for electrification of a fully electric row-crop tractor. Abstract. Power sources such as batteries, used for both on-road and off-road vehicles, are advancing at a rapid pace. Electric batteries are becoming more power dense, thus allowing them to be used as a power source to replace previous diesel or gasoline-powered systems. Efforts are underway to transition off-road agricultural vehicles from Internal Combustion Engine (ICE) vehicles to electric vehicles (EVs); however, the energy requirements of typical agricultural field operations need to be fully understood before such a transition can occur. Theoretical prediction equations available in the American Society of Agricultural and Biological Engineers (ASABE) standards or the use of engine load data from a tractor’s Controller Area Network (CAN) bus are two methods for determining the energy demands of implements on tractors. In this study, tractor CAN bus data was collected from multiple no-till corn planting operations to estimate the energy requirements of the planting operation in kWh. The estimated energy requirement was used to determine the equivalent physical mass and volume of a lithium-ion battery needed to power a hypothetical fully electric tractor for comparable planting operations. The estimated battery capacities using the worst-case field-use scenario in this study were 1117 kWh for operating a 16-row planter to plant 68 ha (168 acre) in a day at an average ground speed of 8.6 km h-1 (5.4 mph) for 14 hours, and 2658 kWh for operating a 48-row planter to plant 158 ha (391 acre) in a day at an average ground speed of 8.9 km h-1 (5.6 mph) for 15 hours. Given the current battery energy density requirements, the equivalent battery masses and volumes were found to be 5,319 kg and 3.33 m3, 12,657 kg and 7.93 m3, for 16-row planter and 48-row planter, respectively. These high kWh estimates needed to power future fully-electric tractor power units are based on worst-case scenarios that could be encountered in real field operations that use wide planters over long operating hours. Keywords: Battery, Controller Area Network, Electric Vehicles, Electrification, No-till, Planting, Row-crop, Tractor.
- 1 January 2023
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Journal of the ASABE
- Vol. 66 (6) , 1481-1496
Estimating Battery Size Requirements for Tractor Electrification of Row-Crop Planting Operations
Highlights Calculate and compare engine power needed for row-crop planting from ASAE standards and reported CAN data. Estimate energy requirements and the equivalent electric battery’s volume and mass for row-crop tractor. Discuss the feasibility for electrification of a fully electric row-crop tractor. Abstract. Power sources such as batteries, used for both on-road and off-road vehicles, are advancing at a rapid pace. Electric batteries are becoming more power dense, thus allowing them to be used as a power source to replace previous diesel or gasoline-powered systems. Efforts are underway to transition off-road agricultural vehicles from Internal Combustion Engine (ICE) vehicles to electric vehicles (EVs); however, the energy requirements of typical agricultural field operations need to be fully understood before such a transition can occur. Theoretical prediction equations available in the American Society of Agricultural and Biological Engineers (ASABE) standards or the use of engine load data from a tractor’s Controller Area Network (CAN) bus are two methods for determining the energy demands of implements on tractors. In this study, tractor CAN bus data was collected from multiple no-till corn planting operations to estimate the energy requirements of the planting operation in kWh. The estimated energy requirement was used to determine the equivalent physical mass and volume of a lithium-ion battery needed to power a hypothetical fully electric tractor for comparable planting operations. The estimated battery capacities using the worst-case field-use scenario in this study were 1117 kWh for operating a 16-row planter to plant 68 ha (168 acre) in a day at an average ground speed of 8.6 km h-1 (5.4 mph) for 14 hours, and 2658 kWh for operating a 48-row planter to plant 158 ha (391 acre) in a day at an average ground speed of 8.9 km h-1 (5.6 mph) for 15 hours. Given the current battery energy density requirements, the equivalent battery masses and volumes were found to be 5,319 kg and 3.33 m3, 12,657 kg and 7.93 m3, for 16-row planter and 48-row planter, respectively. These high kWh estimates needed to power future fully-electric tractor power units are based on worst-case scenarios that could be encountered in real field operations that use wide planters over long operating hours. Keywords: Battery, Controller Area Network, Electric Vehicles, Electrification, No-till, Planting, Row-crop, Tractor.
- 1 April 2018
- Published by Elsevier in Journal of Equine Veterinary Science
- Vol. 63, 1-7
Location on the Body of a Wearable Accelerometer Affects Accuracy of Data for Identifying Equine Gaits
- 1 April 2018
- Published by Elsevier in Journal of Equine Veterinary Science
- Vol. 63, 1-7
Location on the Body of a Wearable Accelerometer Affects Accuracy of Data for Identifying Equine Gaits
- Open Access
- 1 January 2017
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Applied Engineering in Agriculture
- Vol. 33 (5) , 679-686
Tractor Power Take-Off Torque Measurement and Data Acquisition System
: With the mechanization of agricultural operations, agricultural machinery management has become an extensive research field. Sizing tractors and implements to provide the most efficient power transfer has become an ongoing process with advances in technology. Utilization of the rotational power transferred through gear trains from the tractor engine to the power take-off (PTO) shaft is one of the most efficient methods of power transfer to an implement. This research used commercially available torque sensors that were installed on a tractor PTO shaft for measuring the torque delivered to an implement. The torque sensor was calibrated using the Nebraska Tractor Test Lab’s (NTTL) dynamometer by following the Organisation for Economic Co-operation and Development (OECD) Code 2 test procedure for varying PTO loads. The calibration of the sensor was verified using the full load at varying speeds test as described in the OECD Code 2. Tractor PTO shaft torque values measured by the torque sensor were compared to the NTTL’s dynamometer torque measurement. Differences in torque values measured between the sensor and the dynamometer ranged from 3 to 23 N·m. Student’s t-test showed no significant difference between the measurements during the full load varying speed tests which demonstrated that the sensor can be mounted on the tractor’s PTO shaft for torque data collection in field operations. Keywords: Data Acquisition, LabVIEW, Power Take-off, Torque, Tractor.
- 1 January 2017
- Published by American Society of Agricultural and Biological Engineers (ASABE) in Applied Engineering in Agriculture
- Vol. 33 (5) , 679-686
Open AccessTractor Power Take-Off Torque Measurement and Data Acquisition System
: With the mechanization of agricultural operations, agricultural machinery management has become an extensive research field. Sizing tractors and implements to provide the most efficient power transfer has become an ongoing process with advances in technology. Utilization of the rotational power transferred through gear trains from the tractor engine to the power take-off (PTO) shaft is one of the most efficient methods of power transfer to an implement. This research used commercially available torque sensors that were installed on a tractor PTO shaft for measuring the torque delivered to an implement. The torque sensor was calibrated using the Nebraska Tractor Test Lab’s (NTTL) dynamometer by following the Organisation for Economic Co-operation and Development (OECD) Code 2 test procedure for varying PTO loads. The calibration of the sensor was verified using the full load at varying speeds test as described in the OECD Code 2. Tractor PTO shaft torque values measured by the torque sensor were compared to the NTTL’s dynamometer torque measurement. Differences in torque values measured between the sensor and the dynamometer ranged from 3 to 23 N·m. Student’s t-test showed no significant difference between the measurements during the full load varying speed tests which demonstrated that the sensor can be mounted on the tractor’s PTO shaft for torque data collection in field operations. Keywords: Data Acquisition, LabVIEW, Power Take-off, Torque, Tractor.
- 1 February 2016
- Published by Elsevier in Computers and Electronics in Agriculture
- Vol. 121, 290-300
In-field fuel use and load states of agricultural field machinery
- 1 February 2016
- Published by Elsevier in Computers and Electronics in Agriculture
- Vol. 121, 290-300
In-field fuel use and load states of agricultural field machinery