Benjamin Phua
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Benjamin Phua has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Alison Lennon
3 shared publicationsPei-Chieh Hsiao
3 shared publicationsXi Wang
2 shared publicationsXiaowei Shen
2 shared publicationsAlex Stokes
1 shared publication- Alison Lennon
School of Photovoltaic and Renewable Energy Engineering, The University of New South Wales, Sydney, NSW 2052, Australia
1 shared publication
Latest Publications
- 1 February 2020
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 205
Plated metal adhesion to picosecond laser-ablated silicon solar cells: Influence of surface chemistry and wettability
- 1 February 2020
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 205
Plated metal adhesion to picosecond laser-ablated silicon solar cells: Influence of surface chemistry and wettability
- 1 January 2019
- Published by Elsevier in Solar Energy
- Vol. 178, 61-68
Towards a more reliable manufacturing future – Automatic classification of failure modes during adhesion testing of silicon solar cells
- 1 January 2019
- Published by Elsevier in Solar Energy
- Vol. 178, 61-68
Towards a more reliable manufacturing future – Automatic classification of failure modes during adhesion testing of silicon solar cells
- 12 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (4) , 952-959
266-nm ps Laser Ablation for Copper-Plated p-Type Selective Emitter PERC Silicon Solar Cells
Application of 266-nm picosecond (ps) laser ablation and copper (Cu)-plated metallization to p-type selective emitter (SE) passivated emitter and rear cells (PERC) is reported in this paper. Use of a 266-nm ps laser resulted in similar laser-induced periodic surface structures as observed for 355-nm ps laser ablation of a silicon (Si) nitride antireflection coating (ARC) on random-textured Si solar cell surfaces. In addition, it is shown that 266-nm ps laser ablation results in the formation of amorphous Si with an underlying distorted crystalline Si layer at the laser-ablated surfaces. The successful alignment of laser-ablated openings to the heavily doped SE regions resulted in a comparable cell efficiency of Cu-plated SE PERC cells to screen-printed controls, with a maximum cell efficiency of 20.6% being achieved for the Cu-plated cells. The plated cell performance was limited by the recombination losses, and in particular nonideal recombination caused by the use of a shallow emitter, which had been optimized for screen-printed metallization. Engineering of an SE with a junction depth of 0.52 μm in the heavily doped regions resulted in a 0.3% absolute increase in pseudo fill factor and demonstrated the importance of displacing the p-n junction from the laser-ablated Si surface. Although 355-nm ps laser ablation has been demonstrated to result in strong busbar adhesion in previous reports of Cu-plated cells, significant variability in the busbar adhesion of the fully plated SE PERC cells resulted by 266-nm ps laser ablation. The predicted increased sensitivity of 266-nm laser ablation to the ARC thickness and the possibility that surface oxides were not uniformly removed across wafers before plating may have affected the uniformity of silicide formation and hence the adhesion of the plated busbars.
- 12 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (4) , 952-959
266-nm ps Laser Ablation for Copper-Plated p-Type Selective Emitter PERC Silicon Solar Cells
Application of 266-nm picosecond (ps) laser ablation and copper (Cu)-plated metallization to p-type selective emitter (SE) passivated emitter and rear cells (PERC) is reported in this paper. Use of a 266-nm ps laser resulted in similar laser-induced periodic surface structures as observed for 355-nm ps laser ablation of a silicon (Si) nitride antireflection coating (ARC) on random-textured Si solar cell surfaces. In addition, it is shown that 266-nm ps laser ablation results in the formation of amorphous Si with an underlying distorted crystalline Si layer at the laser-ablated surfaces. The successful alignment of laser-ablated openings to the heavily doped SE regions resulted in a comparable cell efficiency of Cu-plated SE PERC cells to screen-printed controls, with a maximum cell efficiency of 20.6% being achieved for the Cu-plated cells. The plated cell performance was limited by the recombination losses, and in particular nonideal recombination caused by the use of a shallow emitter, which had been optimized for screen-printed metallization. Engineering of an SE with a junction depth of 0.52 μm in the heavily doped regions resulted in a 0.3% absolute increase in pseudo fill factor and demonstrated the importance of displacing the p-n junction from the laser-ablated Si surface. Although 355-nm ps laser ablation has been demonstrated to result in strong busbar adhesion in previous reports of Cu-plated cells, significant variability in the busbar adhesion of the fully plated SE PERC cells resulted by 266-nm ps laser ablation. The predicted increased sensitivity of 266-nm laser ablation to the ARC thickness and the possibility that surface oxides were not uniformly removed across wafers before plating may have affected the uniformity of silicide formation and hence the adhesion of the plated busbars.