Jaspreet Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jaspreet Singh has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Ekambir Sidhu
Department of Electronics and Communication Engineering, Punjabi University, Patiala, India
9 shared publications Ekambir Sidhu
Department of Electronics and Communication Engineering, Punjabi University, Patiala, India
3 shared publicationsHemant Bhatia
Department of Mechanical Engineering, Punjabi University, Patiala, India
3 shared publicationsParth Kuchroo
Department of Mechanical Engineering, Punjabi University, Patiala, India
3 shared publicationsSimarjit Singh Saini
Department of Electronics and Comm. Engineering, Punjabi University Patiala Patiala, India
3 shared publications- Avneet Kaur
Department of Electronics and Communication Engineering, Punjabi University, Patiala, India
2 shared publications
Latest Publications
- 29 March 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Computational Materials Science and Engineering
- Vol. 15 (04)
Numerical modeling and theoretical evaluation of CdTe/Si-based efficient thin-film solar cell using a novel Sb 2 Se 3 layer as additional absorber
An additional absorber layer of Sb 2 Se 3 has been used to maximize the photocurrent in this study, which further improves the overall efficiency of solar cells. The paper reports a numerical analysis of novel cadmium telluride (CdTe)/silicon (Si)-based efficient thin-film solar cell integrating antimony selenide (Sb 2 Se[Formula: see text] as an additional absorber layer. The simulation development of the proposed cell is carried out using the Solar Cell Capacitance Simulator (SCAPS-1D) tool and recorded 40.02% power conversion efficiency (PCE). The structure of the solar cell is made up of contacts from metals aluminum (Al) and nickel (Ni), a dual absorber layer from CdTe/Sb 2 Se 3 , cadmium sulfide (CdS) as buffer/window layer and Si as an active layer. The performance of glass/SnO 2 (10[Formula: see text]nm)/CdS (50[Formula: see text]nm)/CdTe (2.5[Formula: see text][Formula: see text]m)/Sb 2 Se 3 (11.2[Formula: see text][Formula: see text]m)/Si (200[Formula: see text][Formula: see text]m)/Al device structure gives potential results as an open circuit voltage ([Formula: see text] of 1009[Formula: see text]mV, short circuit current density ([Formula: see text] of 44.88[Formula: see text]mA/cm 2 , fill factor (FF) of 88.38 and PCE improvement up to 40.02%. The novelty of the presented thin-film solar cell has a Sb 2 Se 3 layer working as an additional absorber, which directly addresses the Shockley–Queisser barrier limits of single junction solar cells. The main praise of the proposed structure introduces the Sb 2 Se 3 layer which achieved the maximum conversion efficiency of 40.02% from 31.65%.
- 29 March 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Computational Materials Science and Engineering
- Vol. 15 (04)
Numerical modeling and theoretical evaluation of CdTe/Si-based efficient thin-film solar cell using a novel Sb 2 Se 3 layer as additional absorber
An additional absorber layer of Sb 2 Se 3 has been used to maximize the photocurrent in this study, which further improves the overall efficiency of solar cells. The paper reports a numerical analysis of novel cadmium telluride (CdTe)/silicon (Si)-based efficient thin-film solar cell integrating antimony selenide (Sb 2 Se[Formula: see text] as an additional absorber layer. The simulation development of the proposed cell is carried out using the Solar Cell Capacitance Simulator (SCAPS-1D) tool and recorded 40.02% power conversion efficiency (PCE). The structure of the solar cell is made up of contacts from metals aluminum (Al) and nickel (Ni), a dual absorber layer from CdTe/Sb 2 Se 3 , cadmium sulfide (CdS) as buffer/window layer and Si as an active layer. The performance of glass/SnO 2 (10[Formula: see text]nm)/CdS (50[Formula: see text]nm)/CdTe (2.5[Formula: see text][Formula: see text]m)/Sb 2 Se 3 (11.2[Formula: see text][Formula: see text]m)/Si (200[Formula: see text][Formula: see text]m)/Al device structure gives potential results as an open circuit voltage ([Formula: see text] of 1009[Formula: see text]mV, short circuit current density ([Formula: see text] of 44.88[Formula: see text]mA/cm 2 , fill factor (FF) of 88.38 and PCE improvement up to 40.02%. The novelty of the presented thin-film solar cell has a Sb 2 Se 3 layer working as an additional absorber, which directly addresses the Shockley–Queisser barrier limits of single junction solar cells. The main praise of the proposed structure introduces the Sb 2 Se 3 layer which achieved the maximum conversion efficiency of 40.02% from 31.65%.
- 1 December 2020
- Published by Elsevier in Journal of Systems Architecture
- Vol. 111
A survey and taxonomy on energy management schemes in wireless sensor networks
- 1 December 2020
- Published by Elsevier in Journal of Systems Architecture
- Vol. 111
A survey and taxonomy on energy management schemes in wireless sensor networks
- 14 September 2020
- Published by Wiley in International Journal of Energy Research
- Vol. 45 (1) , 118-140
Energy harvesting in wireless sensor networks: A taxonomic survey
- 14 September 2020
- Published by Wiley in International Journal of Energy Research
- Vol. 45 (1) , 118-140
Energy harvesting in wireless sensor networks: A taxonomic survey
- 1 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 246-250
Techno-Economic Analysis of Different Lighting Schemes: A Case Study
An optimum lighting design ensures sharp visibility and comfort by considering the light conditions. Further, for optimum utilization of electrical energy, proper care should be taken to avoid overestimation of required illuminance levels. In this paper techno-economic analysis of different lighting schemes viz incandescent lamp, CFL, LED lamp has been done. Further, an efficient arrangement of luminaries for a laboratory is designed in DIALux software.
- 1 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 246-250
Techno-Economic Analysis of Different Lighting Schemes: A Case Study
An optimum lighting design ensures sharp visibility and comfort by considering the light conditions. Further, for optimum utilization of electrical energy, proper care should be taken to avoid overestimation of required illuminance levels. In this paper techno-economic analysis of different lighting schemes viz incandescent lamp, CFL, LED lamp has been done. Further, an efficient arrangement of luminaries for a laboratory is designed in DIALux software.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 301, 516-522
Design and performance analysis of rectangular textile microstrip patch antennas employing different textile materials for Ku band applications
The research paper focus on the design, fabrication and performance analysis of various textile microstrip patch antennas employing different textile materials as substrate suitable to be employed for wearable electronics technology. The radiating patch and ground are made of copper having thickness 0.05mm and conductivity of 5.67 × 107S/m 2 . The textile substrate materials having low dielectric constant-fleece (ε r = 1.04 and tan(δ) = 0.02), felt (ε r = 1.35 and tan(δ) = 0.02), curtain cotton (ε r = 1.47 and tan(δ) = 0.04), polyester (ε r = 1.5 and tan(δ) = 0.02), denim (ε r = 1.6 and tan(δ) = 0.02) and silk (ε r = 2.7 and tan(δ) = 0.02) have been employed as flexible substrates for the proposed antennas. The comparative performance analysis of the proposed textile antennas has been carried out in terms of bandwidth (GHz), return loss (dB), directivity (dBi), gain (dB), input impedance and VSWR. The antennas have been designed and simulated using CST Microwave Studio 2014. It has been analyzed the fleece substrate provides maximum bandwidth of 2.155 GHz, denim substrate provides minimal return loss of -71.86 dB and maximum gain of 8.25 dB whereas felt provides maximum directivity of 11.38dBi. The simulated antennas have been practically fabricated and tested using E5071C Network Analyzer and Anechoic Chamber for experimental validation. The proposed antennas have also been tested for return loss corresponding to different bending angles (15 degrees, 30 degrees, 45 degrees, 60 degrees, 75 degrees). It has been observed that the practical results closely match with the simulated antenna results. The proposed textile antennas can be employed for Ku-band applications (12 GHz-14 GHz), broadcasting satellite (12.4 GHz-12.5 GHz), VSAT and VMES (12.5 GHz-12.75 GHz), VHCM and TV STL (12.7 GHz-13.15 GHz), fixed satellite services (12.75 GHz-13.4 GHz), TV pick up (13.2 GHz-13.25 GHz), space research and aeronautical radio navigation (13.4 GHz-13.75 GHz), radio location (13.75 GHz-14 GHz) applications.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 301, 516-522
Design and performance analysis of rectangular textile microstrip patch antennas employing different textile materials for Ku band applications
The research paper focus on the design, fabrication and performance analysis of various textile microstrip patch antennas employing different textile materials as substrate suitable to be employed for wearable electronics technology. The radiating patch and ground are made of copper having thickness 0.05mm and conductivity of 5.67 × 107S/m 2 . The textile substrate materials having low dielectric constant-fleece (ε r = 1.04 and tan(δ) = 0.02), felt (ε r = 1.35 and tan(δ) = 0.02), curtain cotton (ε r = 1.47 and tan(δ) = 0.04), polyester (ε r = 1.5 and tan(δ) = 0.02), denim (ε r = 1.6 and tan(δ) = 0.02) and silk (ε r = 2.7 and tan(δ) = 0.02) have been employed as flexible substrates for the proposed antennas. The comparative performance analysis of the proposed textile antennas has been carried out in terms of bandwidth (GHz), return loss (dB), directivity (dBi), gain (dB), input impedance and VSWR. The antennas have been designed and simulated using CST Microwave Studio 2014. It has been analyzed the fleece substrate provides maximum bandwidth of 2.155 GHz, denim substrate provides minimal return loss of -71.86 dB and maximum gain of 8.25 dB whereas felt provides maximum directivity of 11.38dBi. The simulated antennas have been practically fabricated and tested using E5071C Network Analyzer and Anechoic Chamber for experimental validation. The proposed antennas have also been tested for return loss corresponding to different bending angles (15 degrees, 30 degrees, 45 degrees, 60 degrees, 75 degrees). It has been observed that the practical results closely match with the simulated antenna results. The proposed textile antennas can be employed for Ku-band applications (12 GHz-14 GHz), broadcasting satellite (12.4 GHz-12.5 GHz), VSAT and VMES (12.5 GHz-12.75 GHz), VHCM and TV STL (12.7 GHz-13.15 GHz), fixed satellite services (12.75 GHz-13.4 GHz), TV pick up (13.2 GHz-13.25 GHz), space research and aeronautical radio navigation (13.4 GHz-13.75 GHz), radio location (13.75 GHz-14 GHz) applications.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 102-106
Raspberry pi based smart fire management system employing sensor based automatic water sprinkler
The smart fire management requires significant surveillance systems to detect and control the fire and fire causing agents automatically. This requirement has been accomplished in this proposed system by employing fire detection system and fire controlling system using Raspberry pi. The fire detection system entails flame detectors along with temperature sensors which reduces the false fire detection rate. The system also notifies the user by emailing the video of fire affected area and gives the updates of room temperature from time to time. A gas leakage sensor has been employed to detect various types of gases like ethane, methane, LPG etc. The proposed fire controlling system performs various functions on detection of fire or gas, which includes switching off the main power supply, switching on the exhaust fan and finally dousing the fire. The water sprinklers have been employed which will be activated on the detection of fire by the employed fire sensors in the system. If temperature rises above the set threshold temperature, then the proposed system will also drop the mail to fire brigade along with the video and notify the user to inform the fire brigade manually. This proposed system can be installed in a hall of maximum area 126ft × 21ft employing one Raspberry pi module.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 102-106
Raspberry pi based smart fire management system employing sensor based automatic water sprinkler
The smart fire management requires significant surveillance systems to detect and control the fire and fire causing agents automatically. This requirement has been accomplished in this proposed system by employing fire detection system and fire controlling system using Raspberry pi. The fire detection system entails flame detectors along with temperature sensors which reduces the false fire detection rate. The system also notifies the user by emailing the video of fire affected area and gives the updates of room temperature from time to time. A gas leakage sensor has been employed to detect various types of gases like ethane, methane, LPG etc. The proposed fire controlling system performs various functions on detection of fire or gas, which includes switching off the main power supply, switching on the exhaust fan and finally dousing the fire. The water sprinklers have been employed which will be activated on the detection of fire by the employed fire sensors in the system. If temperature rises above the set threshold temperature, then the proposed system will also drop the mail to fire brigade along with the video and notify the user to inform the fire brigade manually. This proposed system can be installed in a hall of maximum area 126ft × 21ft employing one Raspberry pi module.
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 338-343
High gain textile rectangular microstrip patch antenna design employing denim substrate for satellite space to Earth downlink applications
This paper proposed a rectangular microstrip patch antenna employing textile substrate material suitable for satellite downlink applications has been demonstrated and analyzed. The paper presents a compact and low profile microstrip fed textile patch antenna employing rectangular patch as a radiating element and Denim as substrate with relative permittivity (dielectric constant) ε r = 1.6 and dimensions 26.8mm × 22.8mm × 0.7mm. The proposed antenna has operating range of frequencies from 10.705 GHz to 10.953GHz. The proposed antenna has gain of 8.49 dB and directivity of 8.35dBi at resonant frequency of 10.832GHz. The performance of the prototype antenna has been examined in terms of return loss (dB), directivity (dBi), gain (dB), input impedance and VSWR. The antenna has been designed, simulated and analyzed using CST Microwave Studio 2014. The proposed textile antenna has impedance bandwidth of 247 MHz with input impedance of 49.9 ohms. The compact size and flexibility of antenna enables the structure to be easily integrated into spacesuit for satellite downlink communication purposes. The antenna has been practically fabricated then tested for experimental validation using E5071C Network Analyzer and anechoic chamber. It has been observed that the practical results closely match with the simulated results of the proposed antenna.
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 338-343
High gain textile rectangular microstrip patch antenna design employing denim substrate for satellite space to Earth downlink applications
This paper proposed a rectangular microstrip patch antenna employing textile substrate material suitable for satellite downlink applications has been demonstrated and analyzed. The paper presents a compact and low profile microstrip fed textile patch antenna employing rectangular patch as a radiating element and Denim as substrate with relative permittivity (dielectric constant) ε r = 1.6 and dimensions 26.8mm × 22.8mm × 0.7mm. The proposed antenna has operating range of frequencies from 10.705 GHz to 10.953GHz. The proposed antenna has gain of 8.49 dB and directivity of 8.35dBi at resonant frequency of 10.832GHz. The performance of the prototype antenna has been examined in terms of return loss (dB), directivity (dBi), gain (dB), input impedance and VSWR. The antenna has been designed, simulated and analyzed using CST Microwave Studio 2014. The proposed textile antenna has impedance bandwidth of 247 MHz with input impedance of 49.9 ohms. The compact size and flexibility of antenna enables the structure to be easily integrated into spacesuit for satellite downlink communication purposes. The antenna has been practically fabricated then tested for experimental validation using E5071C Network Analyzer and anechoic chamber. It has been observed that the practical results closely match with the simulated results of the proposed antenna.
- 10 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1764-1768
Efficient autonomous solar panel and thermo-electric generator (TEG) integrated hybrid energy harvesting system
Solar energy is one of the most covenant renewable energy resources. Imminent technologies within the renewable energy sector have significant potential for more efficiently harnessing the light energy. In this paper, a novel hybrid energy harvesting (EH) system consisting of dynamic offset feed mirrored parabolic dish integrated solar panel with thermoelectric generator (TEG) placed on the lower side of solar panel has been proposed. The proposed energy harvesting system is concurrently harvesting both solar and thermal energy which makes the system suitably named as hybrid energy harvesting system. The mirrored parabolic dish is proficient enough to focus all the light radiations at its focal point where solar panel is placed in order to efficiently harvest the light energy, however, the panel also gets warmed up with these radiations. This heat is transmitted to the TEG's hot side, which is installed at the back of the solar panel and is able to generate voltage if temperature gradient is applied across TEG. The proposed energy harvesting system tracks the motion of the sun throughout the day by clocking/tracking method in order to receive maximum radiations by employing DC geared motor which rotates the dish at the step angle of 6.25 degrees is controlled by Arduino UNO. The proposed system employs the solar panel capable of generating of +12V and capable of harvesting the average power of 6watts. The thermoelectric generator installed at the rear side of solar panel is capable of generating the voltage of 7–12 volts and current of 300–500 mA. The harvested energy by means of solar panel and TEG is sufficient enough to autonomously drive the system as well as to store the harvested energy in +12V lead acid rechargeable batteries. It has been observed that the dynamic offset feed mirrored parabolic dish solar panel energy harvesting system is 81% efficient in comparison to static solar panel whereas the proposed hybrid system is 152.02% more efficient in comparison to static parabolic dish integrated solar panel energy harvesting system. The proposed hybrid energy harvesting system is 38.65% more efficient in comparison to dynamic offset feed mirrored parabolic dish solar panel energy harvesting system. The proposed system can be adeptly employed for various applications such as water heating, street lightning, traffic lights etc.
- 10 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1764-1768
Efficient autonomous solar panel and thermo-electric generator (TEG) integrated hybrid energy harvesting system
Solar energy is one of the most covenant renewable energy resources. Imminent technologies within the renewable energy sector have significant potential for more efficiently harnessing the light energy. In this paper, a novel hybrid energy harvesting (EH) system consisting of dynamic offset feed mirrored parabolic dish integrated solar panel with thermoelectric generator (TEG) placed on the lower side of solar panel has been proposed. The proposed energy harvesting system is concurrently harvesting both solar and thermal energy which makes the system suitably named as hybrid energy harvesting system. The mirrored parabolic dish is proficient enough to focus all the light radiations at its focal point where solar panel is placed in order to efficiently harvest the light energy, however, the panel also gets warmed up with these radiations. This heat is transmitted to the TEG's hot side, which is installed at the back of the solar panel and is able to generate voltage if temperature gradient is applied across TEG. The proposed energy harvesting system tracks the motion of the sun throughout the day by clocking/tracking method in order to receive maximum radiations by employing DC geared motor which rotates the dish at the step angle of 6.25 degrees is controlled by Arduino UNO. The proposed system employs the solar panel capable of generating of +12V and capable of harvesting the average power of 6watts. The thermoelectric generator installed at the rear side of solar panel is capable of generating the voltage of 7–12 volts and current of 300–500 mA. The harvested energy by means of solar panel and TEG is sufficient enough to autonomously drive the system as well as to store the harvested energy in +12V lead acid rechargeable batteries. It has been observed that the dynamic offset feed mirrored parabolic dish solar panel energy harvesting system is 81% efficient in comparison to static solar panel whereas the proposed hybrid system is 152.02% more efficient in comparison to static parabolic dish integrated solar panel energy harvesting system. The proposed hybrid energy harvesting system is 38.65% more efficient in comparison to dynamic offset feed mirrored parabolic dish solar panel energy harvesting system. The proposed system can be adeptly employed for various applications such as water heating, street lightning, traffic lights etc.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Dead cell extracted-urine powered battery energy harvesting system
In this paper, the Dead Cell Extracted-Urine Powered Battery (DCE-UPB) Energy Harvesting system has been proposed. In DCE-UPB, energy is extracted by utilising trash primary cell and human liquid waste-urine. The DCE-UPB design consists of series-parallel combination of dead cell extracted- urine power single chambers. The single chamber cell consists of manganese as substrate along with the urine as electrolyte. The single cell of the proposed system also consists of two electrodes anode and cathode. The single cell of the proposed system has been tested and verified with various electrodes. The two suitable pair of electrodes have been selected i.e. copper/zinc and carbon rod/zinc. Each row consists of 12 cells connected in series and each cell produces an output of 0.85V and 1.2V corresponding to Cu-Zn and C-Zn electrodes respectively. The total output of the system is 10.61V for 145 hours and maximum current spike observed is 42mA. The power output is well enough to drive low power applications. In this proposed system, a LED has been used as low power load and driven by DCE-UPB.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Dead cell extracted-urine powered battery energy harvesting system
In this paper, the Dead Cell Extracted-Urine Powered Battery (DCE-UPB) Energy Harvesting system has been proposed. In DCE-UPB, energy is extracted by utilising trash primary cell and human liquid waste-urine. The DCE-UPB design consists of series-parallel combination of dead cell extracted- urine power single chambers. The single chamber cell consists of manganese as substrate along with the urine as electrolyte. The single cell of the proposed system also consists of two electrodes anode and cathode. The single cell of the proposed system has been tested and verified with various electrodes. The two suitable pair of electrodes have been selected i.e. copper/zinc and carbon rod/zinc. Each row consists of 12 cells connected in series and each cell produces an output of 0.85V and 1.2V corresponding to Cu-Zn and C-Zn electrodes respectively. The total output of the system is 10.61V for 145 hours and maximum current spike observed is 42mA. The power output is well enough to drive low power applications. In this proposed system, a LED has been used as low power load and driven by DCE-UPB.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
High gain textilem microstrip patch antenna design employing denim substrate for Ku band satellite applications
The high gain dual resonant textile microstrip patch antenna with extended ground plane suitable to be employed for satellite Ku band uplink and downlink communication applications has been proposed in this paper. The proposed textile antenna has been fabricated over the wearable textile material - Denim as a substrate having dielectric constant ε r = 1.6. The radiating patch and the ground plane are designed using copper of thickness 0.05mm and conductivity of 5.58×10 6 Siemens/m. The designed textile antenna is dual resonant at 12.64GHz and 13.515GHz with operating bandwidth of 1.57GHz (12.4GHz-13.97GHz) and minimal return loss of -71.86dB and -26.28dB, respectively. The antenna has high gain of 8.25dB at 12.64GHz and 6.14dB at 13.515GHz and directivity of 7.97dBi at 12.64GHz and 5.8dBi at 13.515GHz. The proposed antenna has been designed and simulated using CST Microwave Studio 2014. The proposed textile antenna can be suitably employed for Ku-band applications in vehicle mounted earth stations (12.5GHz-12.75GHz), space research and VSAT applications (12.75GHz-13.5GHz). The simulated antenna has been practically fabricated and tested using E5071C Network Analyzer and anechoic chamber. It has been concluded that the practical results closely match with the simulated antenna results.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
High gain textilem microstrip patch antenna design employing denim substrate for Ku band satellite applications
The high gain dual resonant textile microstrip patch antenna with extended ground plane suitable to be employed for satellite Ku band uplink and downlink communication applications has been proposed in this paper. The proposed textile antenna has been fabricated over the wearable textile material - Denim as a substrate having dielectric constant ε r = 1.6. The radiating patch and the ground plane are designed using copper of thickness 0.05mm and conductivity of 5.58×10 6 Siemens/m. The designed textile antenna is dual resonant at 12.64GHz and 13.515GHz with operating bandwidth of 1.57GHz (12.4GHz-13.97GHz) and minimal return loss of -71.86dB and -26.28dB, respectively. The antenna has high gain of 8.25dB at 12.64GHz and 6.14dB at 13.515GHz and directivity of 7.97dBi at 12.64GHz and 5.8dBi at 13.515GHz. The proposed antenna has been designed and simulated using CST Microwave Studio 2014. The proposed textile antenna can be suitably employed for Ku-band applications in vehicle mounted earth stations (12.5GHz-12.75GHz), space research and VSAT applications (12.75GHz-13.5GHz). The simulated antenna has been practically fabricated and tested using E5071C Network Analyzer and anechoic chamber. It has been concluded that the practical results closely match with the simulated antenna results.