Hung-Liang Cheng

Light-emitting diodes (LEDs) have gained widespread adoption as solid-state lighting sources due to their compact size, long operational lifetime, high brightness, and mechanical robustness. This paper presents the development and implementation of an isolated AC-DC LED electronic lighting driver circuit that integrates a modified flyback converter with a lossless snubber circuit, along with inherent power factor correction (PFC). The proposed design operates the transformer’s magnetizing inductor in the discontinuous conduction mode (DCM), thereby naturally achieving PFC without the need for complex control circuitry. Furthermore, the circuit is capable of recycling the energy stored in the transformer’s leakage inductance, improving overall efficiency. The input current harmonics are shown to comply with the IEC 61000-3-2 Class C standard. A 72 W (36 V/2 A) prototype has been constructed and tested under a 110 V AC input. Experimental results confirm the effectiveness of the proposed design, achieving a power factor of 0.9816, a total harmonic distortion (THD) of 12.094%, an output voltage ripple factor of 9.7%, and an output current ripple factor of 11.22%. These results validate the performance and practical viability of the proposed LED driver architecture.

In the event of power outages caused by natural disasters, accidents, or other emergencies, outdoor emergency lighting systems play a critical role in providing illumination to maintain spatial orientation, facilitate evacuation procedures, and help individuals avoid hazardous areas or locate safe shelters. Compared to traditional lighting technologies, LED-based outdoor emergency lighting offers several advantages, including compact size, long operational lifespan, low energy consumption, high safety, resistance to breakage, and the absence of chemical residue or pollution. These characteristics align with contemporary trends in environmental sustainability and energy efficiency. This study proposes a novel LED driver circuit architecture for outdoor emergency lighting applications. The primary circuit topology is based on an improved buck-boost converter integrated with a flyback converter, forming a hybrid buck-boost-flyback configuration. The proposed circuit is capable of recycling the energy stored in the transformer’s leakage inductance, thereby enhancing overall power conversion efficiency. A 12 W (20 V/0.6 A) prototype LED driver circuit was designed and implemented to validate the performance of the proposed system. Experimental measurements, including waveform analysis and efficiency evaluation, demonstrate that the driver circuit achieves a high efficiency exceeding 91%. These results confirm the practical feasibility and effectiveness of the proposed electronic driver for LED-based outdoor emergency lighting applications.

UV-C LEDs, which offer short-wavelength characteristics and serve as an alternative to traditional UV mercury lamps, represent a new light source for applications in space decontamination and surface disinfection. This paper presents the design and development of a UV-C LED lamp driver circuit configured to operate with a DC-input voltage source for sterilization and germicidal purposes. The primary circuit integrates a modified buck converter with a flyback converter, resulting in an innovative single-stage, single-switch DC-DC power converter. Additionally, the proposed electronic driver recovers energy stored in the transformer’s leakage inductors, enhancing overall circuit efficiency. A prototype driver circuit with a 3.3 W power rating (10 V/330 mA) is developed for a UV-C LED lamp intended for sterilization and germicidal applications with a DC-input voltage source. The experimental results from the prototype circuit, tested at an 18 V DC input, confirm the functionality of the proposed electronic driver for UV-C LED sterilization and germicidal lighting. Additionally, the circuit achieves efficiency exceeding 91%.

Recently, a new type of lighting source, deep ultraviolet light-emitting diode (LED), has appeared in the markets of space purification and surface sterilization. In this paper, a new type of electronic lighting driver for supplying a deep-ultraviolet LED sterilization lamp is proposed and developed. The main circuit combines a buck converter and a flyback converter into a single-stage single-switch buck-flyback AC-DC power converter with power factor correction. In addition, the proposed electronic lighting driver leverages a wide bandgap SiC Schottky diode as the output diode to lower the power diode losses and recycles the energy stored in the leakage inductance of the transformer in order to improve the circuit efficiency. The magnetizing inductor inside the presented AC-DC power converter is designed to operate in discontinuous conduction mode (DCM), which naturally enables power factor correction (PFC). A single-stage prototype driver with a power rating of 3.6 W (90 V/40 mA) was developed and implemented for providing a deep ultraviolet LED disinfection and sterilization lamp. Experimental results show that the measured power factor (PF) is greater than 0.9 and the measured total harmonic distortion (THD) of the input current is less than 18% at an input utility voltage of 110 V. Furthermore, the measured output voltage ripple factor is less than 1% and the output current ripple factor is less than 4%. In addition, the proposed single-stage electronic lighting driver for supplying a deep ultraviolet LED disinfection and sterilization lamp achieves high circuit efficiency (greater than 90%), low circuit component count, and low circuit cost.

A novel ac/dc LED driver with power factor correction and soft-switching functions is proposed. The circuit topology mainly consists of two modified single-ended primary inductance converters (SEPIC) with interleaved operation. The first half stage of SEPIC operates like a boost converter and the second half stage operates like a buck–boost converter. Each boost converter is designed to operate in discontinuous current mode (DCM) to function as a power factor corrector (PFC). The two buck–boost converters that share a commonly coupled inductor are designed to operate at near boundary conduction mode (BCM). Without using any active clamping circuit, auxiliary switch or snubber circuit, the active switches can achieve zero-voltage switching on, and all diodes achieve zero-current switching off. First, operation modes in steady state are analyzed, and the mathematical equations for design component parameters are derived. Finally, a prototype circuit of 180 W rated power was built and tested. Experimental results show satisfactory performance of the proposed circuit.

This article proposes a single-stage ac/dc converter for driving high-power light-emitting diodes. The circuit topology mainly includes two modified Ćuk converters that are interleaved operated. The front semi-stage of Ćuk converter operates like a boost converter while the second semi-stage operates like a buck converter. The boost converters are operated in discontinuous-conduction mode to play the role of power factor corrector. In the buck converters, the two energy-storage inductors are replaced by a coupled inductor. The mutual inductance current of the coupled inductor is almost constant and continuously flows to the output terminal. Therefore, the output voltage ripple can be effectively reduced without using large electrolytic capacitors. In addition, the proposed circuit does not require the use of any snubber circuit or active clamping circuit. All active switches operate at zero-voltage switching on , and all diodes operate at zero-current switching off . This article analyzes the operation modes of the circuit; derives mathematical equations; and designs component parameters. Finally, 180-W prototype circuit was built and tested. The experimental results show that the conversion efficiency at rated power operation is 96.6%; the power factor is as high as 0.996; and the total harmonic distortion of current is 7.18%. The performance is satisfactory and verifies the feasibility of the proposed circuit.

Piezoelectric ceramic actuators utilize an inverse piezoelectric effect to generate high-frequency vibration energy and are widely used in ultrasonic energy conversion circuits. This paper presents a novel drive circuit with input-current shaping (ICS) and soft-switching features which consists of a front AC-DC full-wave bridge rectifier and a rear DC-AC circuit combining a stacked boost converter and a half-bridge resonant inverter for driving a piezoelectric ceramic actuator. To enable ICS functionality in the proposed drive circuit, the inductor of the stacked boost converter sub-circuit is designed to operate in boundary-conduction mode (BCM). In order to allow the two power switches in the proposed drive circuit to achieve zero-voltage switching (ZVS) characteristics, the resonant circuit of the half-bridge resonant inverter sub-circuit is designed as an inductive load. In this paper, a prototype drive circuit for providing piezoelectric ceramic actuators was successfully implemented. Experimental results tested at 110 V input utility voltage show that high power factor (PF > 0.97), low input current total harmonic distortion (THD < 16%), and ZVS characteristics of the power switch were achieved in the prototype drive circuit.

With the global advocacy of green lighting and the urgent need for energy saving and carbon reduction, more and more street lighting applications have entered the era of being replaced by light-emitting diode (LED) lighting sources. This paper presents a new LED streetlight driving circuit applied to a direct current (DC)-input voltage source, which consists of a buck converter combined with a flyback converter to reduce the number of circuit components required and to recover the leakage energy of the transformer to improve energy conversion efficiency. In addition, this study also completed the analysis of the operational principle of the new LED streetlight driving circuit, and developed a prototype LED streetlight driver with DC-input voltage of 48V and output power of 72 W (36 V/2 A). Finally, the measurement results of the prototype circuit show that the output voltage ripple rate was less than 15%, the output current ripple rate was less than 6%, and the circuit efficiency was as high as 91%.

The use of light-emitting diodes (LEDs) in street lighting applications has been greatly welcomed with the current trends of energy saving, environmental protection, carbon reduction, and sustainable development. This paper presents a novel AC-DC LED integrated streetlight driver that combines an interleaved buck converter with a coupled inductor and a half-bridge series resonant converter with a full-bridge rectifier into a single-stage power conversion topology with power factor correction (PFC) and soft switching capabilities. The PFC is achieved by designing the coupling inductor in the interleaved buck converter sub-circuit in discontinuous conduction mode. In addition, the resonant tank in the half-bridge series resonant converter sub-circuit is designed to be similar to an inductive load, thus giving the power switch a zero-voltage switching (ZVS) function, decreasing switching losses and increasing the overall efficiency of the proposed circuit. A prototype circuit of the proposed LED integrated streetlight driver with a power rating of 165 W (235 V/0.7 A) and 110 V input utility voltage has been developed and tested. According to the measurement results, a power factor greater than 0.98, a total harmonic distortion coefficient of the input current less than 3%, and an efficiency greater than 89% were obtained in the AC-DC LED integrated streetlight driver. Therefore, the experimental results are satisfactory and demonstrate the functionality of the proposed AC-DC LED integrated streetlight driver.

The research proposed a novel LED driver with the functions of power-factor correction (PFC) and current balancing. A flyback converter and a Class-D series resonant converter were integrated by sharing an active switch to form a single-stage circuit topology. The flyback converter played the role of a PFC circuit. The component parameters were designed to make the flyback converter to operate at discontinuous-conduction mode (DCM). In this way, the input line current can be sinusoidal, resulting in near unity power factor and low total harmonic distortion in current (THDi). The resonant converter was connected in series with a differential-mode transformer with a turns ratio of 1 to drive four LED strings. The current of the four LED strings will be automatically and evenly balanced by using the 1:1 transformer. This article analyzed the different modes of operation in detail, derived the mathematical equations and designed the parameters of the circuit components. Finally, a 72-W prototype LED driver was implemented and tested. A satisfactory performance has verified the feasibility of the proposed LED driver.