Sasisanker Padmanabhan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sasisanker Padmanabhan has a total of 108 co-authors. Here are the top co-authors by number of shared publications:
- Alexis T. Bell
University of California
4 shared publications John M. Prausnitz
4 shared publicationsSnehal D. Birajdar
4 shared publicationsZhongguo Liu
University of California
4 shared publications- Anjani J. Varma
Polymer Science & Engineering Division, CSIR-National Chemical Laboratory, Pune 411008, India
3 shared publications H. Weingärtner
Department of Physical Chemistry II, Ruhr-University of Bochum, Building NC 6-25, 44780 Bochum, Germany
3 shared publications
Latest Publications
- 7 January 2026
- Published by Sciencedomain International in Journal of Scientific Research and Reports
- Vol. 32 (1) , 769-786
Process Development for Valorisation of Solid and Liquid Waste Stream in Sugar Factories & Bio-ethanol Industries
The objective of this work is the valorisation of some of the waste streams that are generated post the production of bioethanol in sugar factories and distilleries. Boiler ash and process condensate are the two waste streams chosen for this study. This study reports a new approach on extraction of the important components from the boiler ash, containing mainly potassium, by using another waste stream denoted as process condensate. The study shows that the extraction of potassium with process condensate is possible with around 75% potassium extraction efficiency with 80 % potassium purity in a single extraction method. A chief advantage of the current extraction process is that it generates a good quality of distillate, which can be safely recycled back to the fermentation process. This recycled distillate helps in the savings of an additional equivalent amount of fresh process water required for bioethanol fermentation. Analysis of the process condensate reveals that it contains major volatile acidic inhibitors, like acetic, propionic, butyric, iso-butyric, valeric, and iso-valeric acids. These are the major inhibitors for yeast and reduce the efficiency of the bioethanol fermentation process. Following this potassium extraction process, ~90% of these volatile acids are separated and removed. In addition to all the benefits, the process employed in this work helps remove inhibitors, which are microbial contamination, thereby providing the condensate, which can be effectively and safely used as process water back to the fermentation stream to produce bioethanol.
- 7 January 2026
- Published by Sciencedomain International in Journal of Scientific Research and Reports
- Vol. 32 (1) , 769-786
Process Development for Valorisation of Solid and Liquid Waste Stream in Sugar Factories & Bio-ethanol Industries
The objective of this work is the valorisation of some of the waste streams that are generated post the production of bioethanol in sugar factories and distilleries. Boiler ash and process condensate are the two waste streams chosen for this study. This study reports a new approach on extraction of the important components from the boiler ash, containing mainly potassium, by using another waste stream denoted as process condensate. The study shows that the extraction of potassium with process condensate is possible with around 75% potassium extraction efficiency with 80 % potassium purity in a single extraction method. A chief advantage of the current extraction process is that it generates a good quality of distillate, which can be safely recycled back to the fermentation process. This recycled distillate helps in the savings of an additional equivalent amount of fresh process water required for bioethanol fermentation. Analysis of the process condensate reveals that it contains major volatile acidic inhibitors, like acetic, propionic, butyric, iso-butyric, valeric, and iso-valeric acids. These are the major inhibitors for yeast and reduce the efficiency of the bioethanol fermentation process. Following this potassium extraction process, ~90% of these volatile acids are separated and removed. In addition to all the benefits, the process employed in this work helps remove inhibitors, which are microbial contamination, thereby providing the condensate, which can be effectively and safely used as process water back to the fermentation stream to produce bioethanol.
- Open Access
- 1 January 2026
- Published by SCIE Publishing Limited in Green Chemical Technology
- Vol. 3 (1) , 10023
Demethylation of Lignin from Rice-Straw Biorefinery: An Integrated Chemical and Biochemical Approach
SCIEPublish is an international open-access journal publishing service provider run by SCIE Publishing Limited, dedicated to supporting and inspiring scientists or institutions/societies who aspire to publish high-quality journals.
- 1 January 2026
- Published by SCIE Publishing Limited in Green Chemical Technology
- Vol. 3 (1) , 10023
Open AccessDemethylation of Lignin from Rice-Straw Biorefinery: An Integrated Chemical and Biochemical Approach
SCIEPublish is an international open-access journal publishing service provider run by SCIE Publishing Limited, dedicated to supporting and inspiring scientists or institutions/societies who aspire to publish high-quality journals.
- 22 July 2024
- Published by Institutul de Chimie Macromoleculara Petru Poni in Cellulose Chemistry and Technology
- Vol. 58 (5-6) , 529-539
ENHANCEMENT OF PHENOLIC CONTENT AND ANTIOXIDANT PROPERTIES THROUGH CHEMICAL AND BIOCHEMICAL REATMENT OF LIGNIN-RICH RICE STRAW RESIDUE
Valorization of lignin in biorefineries is important as this can lead to enhancement of chemical and physical properties of lignin, making it suitable for applications in polymers, composites and adhesives. Lignin valorization requires overcoming recalcitrance and tailoring for different uses. Here, lignin was extracted from rice straw lignin-rich residue at pH 12, using 4% magnesium oxide and 6% sodium hydroxide on a dry w/w basis. The extracted lignin-rich stream, which had a pH in the range of 9-10, was used further for biochemical transformation. Towards that end, Pseudomonas putida, Sphingomonas paucimobilis, Pseudomonas fluorescens and Bacillus tequilensis were screened for their capability of aromatic dye decolourization. The results of the study show an increase in the total phenolic content in lignin between 50% and 55% after 144 h of treatment with Pseudomonas putida. Concomitant with the increase of phenolics, a four-fold increase in antioxidant activity in gallic acid equivalents was also observed when Pseudomonas putida was used.
- 22 July 2024
- Published by Institutul de Chimie Macromoleculara Petru Poni in Cellulose Chemistry and Technology
- Vol. 58 (5-6) , 529-539
ENHANCEMENT OF PHENOLIC CONTENT AND ANTIOXIDANT PROPERTIES THROUGH CHEMICAL AND BIOCHEMICAL REATMENT OF LIGNIN-RICH RICE STRAW RESIDUE
Valorization of lignin in biorefineries is important as this can lead to enhancement of chemical and physical properties of lignin, making it suitable for applications in polymers, composites and adhesives. Lignin valorization requires overcoming recalcitrance and tailoring for different uses. Here, lignin was extracted from rice straw lignin-rich residue at pH 12, using 4% magnesium oxide and 6% sodium hydroxide on a dry w/w basis. The extracted lignin-rich stream, which had a pH in the range of 9-10, was used further for biochemical transformation. Towards that end, Pseudomonas putida, Sphingomonas paucimobilis, Pseudomonas fluorescens and Bacillus tequilensis were screened for their capability of aromatic dye decolourization. The results of the study show an increase in the total phenolic content in lignin between 50% and 55% after 144 h of treatment with Pseudomonas putida. Concomitant with the increase of phenolics, a four-fold increase in antioxidant activity in gallic acid equivalents was also observed when Pseudomonas putida was used.
- 7 September 2016
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 7 (2) , 179-189
Pilot-scale pretreatments of sugarcane bagasse with steam explosion and mineral acid, organic acid, and mixed acids: synergies, enzymatic hydrolysis efficiencies, and structure-morphology correlations
- 7 September 2016
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 7 (2) , 179-189
Pilot-scale pretreatments of sugarcane bagasse with steam explosion and mineral acid, organic acid, and mixed acids: synergies, enzymatic hydrolysis efficiencies, and structure-morphology correlations
- 19 August 2016
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 30 (9) , 7310-7318
Effect of Mixed Acid Catalysis on Pretreatment and Enzymatic Digestibility of Sugar Cane Bagasse
- 19 August 2016
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 30 (9) , 7310-7318
Effect of Mixed Acid Catalysis on Pretreatment and Enzymatic Digestibility of Sugar Cane Bagasse
- Open Access
- 7 June 2016
- Published by Springer Nature in 3 Biotech
- Vol. 6 (2) , 126
Pretreatment and enzymatic process modification strategies to improve efficiency of sugar production from sugarcane bagasse
Pretreatment and enzymatic hydrolysis play a critical role in the economic production of sugars and fuels from lignocellulosic biomass. In this study, we evaluated diverse pilot-scale pretreatments and different post-pretreatment strategies for the production of fermentable sugars from sugarcane bagasse. For the pretreatment of bagasse at pilot-scale level, steam explosion without catalyst and combination of sulfuric and oxalic acids at low and high loadings were used. Subsequently, to enhance the efficiency of enzymatic hydrolysis of the pretreated bagasse, three different post-pretreatment process schemes were investigated. In the first scheme (Scheme 1), enzymatic hydrolysis was conducted on the whole pretreated slurry, without treatments such as washing or solid–liquid separation. In the second scheme (Scheme 2), the pretreated slurry was first pressure filtered to yield a solid and liquid phase. Following filtration, the separated liquid phase was remixed with the solid wet cake to generate slurry, which was then subsequently used for enzymatic hydrolysis. In the third scheme (Scheme 3), the pretreated slurry was washed with more water and filtered to obtain a solid and liquid phase, in which only the former was subjected to enzymatic hydrolysis. A 10 % higher enzymatic conversion was obtained in Scheme 2 than Scheme 1, while Scheme 3 resulted in only a 5–7 % increase due to additional washing unit operation and solid–liquid separation. Dynamic light scattering experiments conducted on post-pretreated bagasse indicate decrease of particle size due to solid–liquid separation involving pressure filtration provided increased the yield of C6 sugars. It is anticipated that different process modification methods used in this study before the enzymatic hydrolysis step can make the overall cellulosic ethanol process effective and possibly cost effective.
- 7 June 2016
- Published by Springer Nature in 3 Biotech
- Vol. 6 (2) , 126
Open AccessPretreatment and enzymatic process modification strategies to improve efficiency of sugar production from sugarcane bagasse
Pretreatment and enzymatic hydrolysis play a critical role in the economic production of sugars and fuels from lignocellulosic biomass. In this study, we evaluated diverse pilot-scale pretreatments and different post-pretreatment strategies for the production of fermentable sugars from sugarcane bagasse. For the pretreatment of bagasse at pilot-scale level, steam explosion without catalyst and combination of sulfuric and oxalic acids at low and high loadings were used. Subsequently, to enhance the efficiency of enzymatic hydrolysis of the pretreated bagasse, three different post-pretreatment process schemes were investigated. In the first scheme (Scheme 1), enzymatic hydrolysis was conducted on the whole pretreated slurry, without treatments such as washing or solid–liquid separation. In the second scheme (Scheme 2), the pretreated slurry was first pressure filtered to yield a solid and liquid phase. Following filtration, the separated liquid phase was remixed with the solid wet cake to generate slurry, which was then subsequently used for enzymatic hydrolysis. In the third scheme (Scheme 3), the pretreated slurry was washed with more water and filtered to obtain a solid and liquid phase, in which only the former was subjected to enzymatic hydrolysis. A 10 % higher enzymatic conversion was obtained in Scheme 2 than Scheme 1, while Scheme 3 resulted in only a 5–7 % increase due to additional washing unit operation and solid–liquid separation. Dynamic light scattering experiments conducted on post-pretreated bagasse indicate decrease of particle size due to solid–liquid separation involving pressure filtration provided increased the yield of C6 sugars. It is anticipated that different process modification methods used in this study before the enzymatic hydrolysis step can make the overall cellulosic ethanol process effective and possibly cost effective.
- Open Access
- 11 January 2016
- Published by Springer Nature in 3 Biotech
- Vol. 6 (1) , 23
Delignification of miscanthus using ethylenediamine (EDA) with or without ammonia and subsequent enzymatic hydrolysis to sugars
Pretreatment of miscanthus is essential for efficient enzymatic production of cellulosic ethanol. This study reports a possible pretreatment method for miscanthus using aqueous ethylenediamine (EDA) for 30 min at 180 °C with or without ammonia. The mass ratio of miscanthus to EDA was varied from 1:3, 1:1, and 1:0.5, keeping the mass ratio of miscanthus to liquid (EDA + Water) constant at 1:8. The ammonia-to-miscanthus ratio was 1:0.25. After pretreatment with a ratio of 1:3 miscanthus to EDA, about 75 % of the lignin was removed from the raw miscanthus with 90 % retention of cellulose and 50 % of hemicellulose in the recovered solid. Enzymatic hydrolysis of the recovered solid miscanthus gave 63 % glucose and 62 % xylose conversion after 72 h. EDA provides an effective pretreatment for miscanthus, achieving good delignification and enhanced sugar yield by enzyme hydrolysis. Results using aqueous EDA with or without ammonia are much better than those using hot water and compare favorably with those using aqueous ammonia. The delignification efficiency of EDA pretreatment is high compared to that for hot-water pretreatment and is nearly as efficient as that obtained for aqueous-ammonia pretreatment.
- 11 January 2016
- Published by Springer Nature in 3 Biotech
- Vol. 6 (1) , 23
Open AccessDelignification of miscanthus using ethylenediamine (EDA) with or without ammonia and subsequent enzymatic hydrolysis to sugars
Pretreatment of miscanthus is essential for efficient enzymatic production of cellulosic ethanol. This study reports a possible pretreatment method for miscanthus using aqueous ethylenediamine (EDA) for 30 min at 180 °C with or without ammonia. The mass ratio of miscanthus to EDA was varied from 1:3, 1:1, and 1:0.5, keeping the mass ratio of miscanthus to liquid (EDA + Water) constant at 1:8. The ammonia-to-miscanthus ratio was 1:0.25. After pretreatment with a ratio of 1:3 miscanthus to EDA, about 75 % of the lignin was removed from the raw miscanthus with 90 % retention of cellulose and 50 % of hemicellulose in the recovered solid. Enzymatic hydrolysis of the recovered solid miscanthus gave 63 % glucose and 62 % xylose conversion after 72 h. EDA provides an effective pretreatment for miscanthus, achieving good delignification and enhanced sugar yield by enzyme hydrolysis. Results using aqueous EDA with or without ammonia are much better than those using hot water and compare favorably with those using aqueous ammonia. The delignification efficiency of EDA pretreatment is high compared to that for hot-water pretreatment and is nearly as efficient as that obtained for aqueous-ammonia pretreatment.
- 1 September 2015
- Published by Elsevier in Separation and Purification Technology
- Vol. 151, 115-123
Continuous predispersed solvent extraction process for the downstream separation of 2,3-butanediol from fermentation broth
- 1 September 2015
- Published by Elsevier in Separation and Purification Technology
- Vol. 151, 115-123
Continuous predispersed solvent extraction process for the downstream separation of 2,3-butanediol from fermentation broth
- 1 September 2015
- Published by Elsevier in Process Biochemistry
- Vol. 50 (9) , 1449-1458
Continuous countercurrent liquid–liquid extraction method for the separation of 2,3-butanediol from fermentation broth using n-butanol and phosphate salt
- 1 September 2015
- Published by Elsevier in Process Biochemistry
- Vol. 50 (9) , 1449-1458
Continuous countercurrent liquid–liquid extraction method for the separation of 2,3-butanediol from fermentation broth using n-butanol and phosphate salt
- 23 March 2015
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 114 (12) , 128101
Orientational Alignment of Amyloidogenic Proteins in Pre-Aggregated Solutions
In the present study we combine dielectric relaxation spectroscopy with generalized Born simulations to explore the role of orientational order for protein aggregation in solutions of bovine pancreatic insulin at various conditions. Under aggregation-prone conditions at low , insulin monomers prefer antiparallel dipole alignments, which are consistent with the orientation of the monomeric subunits in the dimer structure. This alignment is also true for two dimers, suggesting that already at moderate protein concentrations the species assemble in equilibrium clusters, in which the molecules adopt preferred orientations also found for the protomers of the corresponding oligomers.- 23 March 2015
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 114 (12) , 128101
Orientational Alignment of Amyloidogenic Proteins in Pre-Aggregated Solutions
In the present study we combine dielectric relaxation spectroscopy with generalized Born simulations to explore the role of orientational order for protein aggregation in solutions of bovine pancreatic insulin at various conditions. Under aggregation-prone conditions at low , insulin monomers prefer antiparallel dipole alignments, which are consistent with the orientation of the monomeric subunits in the dimer structure. This alignment is also true for two dimers, suggesting that already at moderate protein concentrations the species assemble in equilibrium clusters, in which the molecules adopt preferred orientations also found for the protomers of the corresponding oligomers.