Hiromitsu Kozuka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Hiromitsu Kozuka has a total of 200 co-authors. Here are the top co-authors by number of shared publications:
Sumio Sakka
Fukui Universitu of Technology
32 shared publicationsToshinobu Yoko
Kyoto University
27 shared publications- Hiroaki Uchiyama
Department of Chemistry and Materials Engineering, Kansai University, 3-3-35 Yamate-cho, Suita 564-8680, Japan
21 shared publications Hiroaki Uchiyama
Kansai University
20 shared publicationsGaoling Zhao
9 shared publicationsAkihiro Yamano
Faculty of Engineering Science, Kansai University, Suita , Osaka 564-8680, Japan
8 shared publications
Latest Publications
- Open Access
- 26 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (7) , 5894-5903
Non-stick performance of polymethylsilsesquioxane thin films synthesized by sol–gel spray coating
Polymethylsilsesquioxane (PMSQ) coatings, synthesized via a strongly acidic sol–gel process, exhibited excellent non-stick performance.
- 26 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (7) , 5894-5903
Open AccessNon-stick performance of polymethylsilsesquioxane thin films synthesized by sol–gel spray coating
Polymethylsilsesquioxane (PMSQ) coatings, synthesized via a strongly acidic sol–gel process, exhibited excellent non-stick performance.
- 3 September 2025
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 116 (2) , 1132-1141
Effect of the humidity during spin-coating on the microstructure and porosity of sol–gel-derived zirconia thin films
- 3 September 2025
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 116 (2) , 1132-1141
Effect of the humidity during spin-coating on the microstructure and porosity of sol–gel-derived zirconia thin films
- 1 October 2024
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 16 (1)
Anti‐glare performance of sol‐gel‐derived spray coatings prepared with various water‐to‐alkoxide ratios
We fabricated anti‐glare (AG) coatings on glass sheets by spraying alkoxide‐derived silica sols and demonstrated that the water‐to‐alkoxide ratio is one of the key factors for improving AG performance and sol stability. We synthesized silica sols using tetraethylorthosilicate (TEOS), water, nitric acid, and denatured ethanol and sprayed them on sheets of chemically strengthened glass. The molar ratios of water to TEOS (r) were 3, 7, and 14. The sol with r = 7 provided a higher arithmetic‐mean height (Sa), smaller autocorrelation length (Sal), and better optical properties (lower gloss, higher haze, and lower sparkle level) than the sol with r = 3. An excessive amount of water at r = 14 yielded a large Sal and a high sparkle level. As the storage time of the sols increased, higher r values caused a more pronounced increase in Sa. Although none of the sols showed noticeable temporal changes during dynamic light scattering measurements, solutions with higher r values exhibited a more remarkable reduction in the retention time during liquid chromatography with a styrene‐divinylbenzene matrix. Hence, an excessive amount of water was thought to cause hydrophilization of the polymerized species during storage.
- 1 October 2024
- Published by Wiley in International Journal of Applied Glass Science
- Vol. 16 (1)
Anti‐glare performance of sol‐gel‐derived spray coatings prepared with various water‐to‐alkoxide ratios
We fabricated anti‐glare (AG) coatings on glass sheets by spraying alkoxide‐derived silica sols and demonstrated that the water‐to‐alkoxide ratio is one of the key factors for improving AG performance and sol stability. We synthesized silica sols using tetraethylorthosilicate (TEOS), water, nitric acid, and denatured ethanol and sprayed them on sheets of chemically strengthened glass. The molar ratios of water to TEOS (r) were 3, 7, and 14. The sol with r = 7 provided a higher arithmetic‐mean height (Sa), smaller autocorrelation length (Sal), and better optical properties (lower gloss, higher haze, and lower sparkle level) than the sol with r = 3. An excessive amount of water at r = 14 yielded a large Sal and a high sparkle level. As the storage time of the sols increased, higher r values caused a more pronounced increase in Sa. Although none of the sols showed noticeable temporal changes during dynamic light scattering measurements, solutions with higher r values exhibited a more remarkable reduction in the retention time during liquid chromatography with a styrene‐divinylbenzene matrix. Hence, an excessive amount of water was thought to cause hydrophilization of the polymerized species during storage.
- 5 May 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (9) , 5749-5761
Highly crystalline yttria‐stabilized zirconia and titania thin films on plastic substrates via sol‐gel transfer process
We prepared yttria‐stabilized zirconia (YSZ) and titania crystalline thin films on polycarbonate (PC) substrates by the sol‐gel transfer technique that we have developed recently. Precursor gel films were deposited by spin‐coating on a polyimide/polyvinylpyrrolidone mixture layer on Si(100) substrates, and then were calcined at 600°C. The spin‐coating and the calcination were cycled, followed by final firing at 600–1000°C, to obtain 140–190 nm thick, YSZ and titania crystalline thin films. The film densification progressed as the final firing temperature increased, where the porosity calculated from the refractive index decreased down to a few percent. The film thus obtained was heated at 190°C on a hot plate, and a PC substrate was pressed on the film to transfer it to the PC substrate. The transferability quantified by image analysis of the film area was found to be significantly different between the YSZ and titania films. In the case of YSZ films, the area of silicon that was fractured and adhered to the transferred film increased significantly with increasing firing temperature, leading to a decrease down to 0% in the fraction of the successful transfer area without such a damage. On the other hand, the fraction of the successful transfer area remained around 90% irrespective of the firing temperature for the titania films. The surface of the titania films that were fired at 800–1000°C and transferred to PC substrates had voids of several tens nm scale, which may have been formed during anatase‐to‐rutile phase transformation. We thought that the reduced titania/Si(100) contact area due to such void formation facilitated the delamination of the titania films from Si(100) substrates. High temperature firing, which promotes crystallization and densification of films, thus affects differently the film transferability to plastic substrates, depending on the type of films. The work also suggested possible use of titania films as release‐assisting layers.
- 5 May 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (9) , 5749-5761
Highly crystalline yttria‐stabilized zirconia and titania thin films on plastic substrates via sol‐gel transfer process
We prepared yttria‐stabilized zirconia (YSZ) and titania crystalline thin films on polycarbonate (PC) substrates by the sol‐gel transfer technique that we have developed recently. Precursor gel films were deposited by spin‐coating on a polyimide/polyvinylpyrrolidone mixture layer on Si(100) substrates, and then were calcined at 600°C. The spin‐coating and the calcination were cycled, followed by final firing at 600–1000°C, to obtain 140–190 nm thick, YSZ and titania crystalline thin films. The film densification progressed as the final firing temperature increased, where the porosity calculated from the refractive index decreased down to a few percent. The film thus obtained was heated at 190°C on a hot plate, and a PC substrate was pressed on the film to transfer it to the PC substrate. The transferability quantified by image analysis of the film area was found to be significantly different between the YSZ and titania films. In the case of YSZ films, the area of silicon that was fractured and adhered to the transferred film increased significantly with increasing firing temperature, leading to a decrease down to 0% in the fraction of the successful transfer area without such a damage. On the other hand, the fraction of the successful transfer area remained around 90% irrespective of the firing temperature for the titania films. The surface of the titania films that were fired at 800–1000°C and transferred to PC substrates had voids of several tens nm scale, which may have been formed during anatase‐to‐rutile phase transformation. We thought that the reduced titania/Si(100) contact area due to such void formation facilitated the delamination of the titania films from Si(100) substrates. High temperature firing, which promotes crystallization and densification of films, thus affects differently the film transferability to plastic substrates, depending on the type of films. The work also suggested possible use of titania films as release‐assisting layers.
- 28 December 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 314
Glass transition of amorphous materials composed of organically modified metal oxo-oligomers
- 28 December 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 314
Glass transition of amorphous materials composed of organically modified metal oxo-oligomers
- 18 February 2023
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 114 (1) , 65-74
Bendability of polycrystalline titania thin films fabricated on plastic substrates by the sol–gel transfer technique via firing at temperatures over 600 °C
- 18 February 2023
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 114 (1) , 65-74
Bendability of polycrystalline titania thin films fabricated on plastic substrates by the sol–gel transfer technique via firing at temperatures over 600 °C
- 22 June 2022
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 104 (3) , 673-684
Fundamental properties of alkoxide-derived titania gel films providing plastics surface with high refractive index
- 22 June 2022
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 104 (3) , 673-684
Fundamental properties of alkoxide-derived titania gel films providing plastics surface with high refractive index
- 20 May 2022
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 104 (3) , 478-483
Preparation of transparent and mechanically hard inorganic-organic hybrid thick films from 3-glycidoxypropyltrimethoxysilane and zirconium propoxide
- 20 May 2022
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 104 (3) , 478-483
Preparation of transparent and mechanically hard inorganic-organic hybrid thick films from 3-glycidoxypropyltrimethoxysilane and zirconium propoxide