Juan Vargas-Machuca
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Juan Vargas-Machuca has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Alberto M. Coronado
Laboratorio de Sistemas Inteligentes, EPIME, Universidad Nacional Tecnológica de Lima Sur (UNTELS), Lima, Peru
4 shared publications - Fabio C. Zegarra
Laboratorio de Sistemas Inteligentes, EPIME, Universidad Nacional Tecnológica de Lima Sur (UNTELS), Lima, Peru
4 shared publications A. Rojas
National Research Institute, National University of Engineering
1 shared publication- Antoni Mauricio
Universidad Católica San Pablo
1 shared publication - Avid Roman-Gonzalez
Aerospace Sciences & Health Research Laboratory (INCAS-Lab), Universidad Nacional Tecnológica de Lima Sur, Villa el Salvador, Peru
1 shared publication - Carlos Rodrigues Pereira Belchior
Federal University of Rio de Janeiro
1 shared publication
Latest Publications
- 18 October 2023
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
A Comparative Study of CNN, LSTM, BiLSTM, and GRU Architectures for Tool Wear Prediction in Milling Processes
Accurately predicting machine tool wear requires models capable of capturing complex, nonlinear interactions in multivariate time series inputs. Recurrent neural networks (RNNs) are well-suited to this task, owing to their memory mechanisms and capacity to construct highly complex models. In...
- 18 October 2023
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
A Comparative Study of CNN, LSTM, BiLSTM, and GRU Architectures for Tool Wear Prediction in Milling Processes
Accurately predicting machine tool wear requires models capable of capturing complex, nonlinear interactions in multivariate time series inputs. Recurrent neural networks (RNNs) are well-suited to this task, owing to their memory mechanisms and capacity to construct highly complex models. In...
- 25 August 2023
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
Unsupervised and Supervised Machine Learning Methods for Cutting Tool Path Clustering and RUL Estimation in Manufacturing
Machine learning has been widely used in manufacturing, leading to significant advances in diverse problems, including the prediction of wear and remaining useful life (RUL) of machine tools. However, the data used in many cases correspond to simple and stable processes that differ from practical...
- 25 August 2023
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
Unsupervised and Supervised Machine Learning Methods for Cutting Tool Path Clustering and RUL Estimation in Manufacturing
Machine learning has been widely used in manufacturing, leading to significant advances in diverse problems, including the prediction of wear and remaining useful life (RUL) of machine tools. However, the data used in many cases correspond to simple and stable processes that differ from practical...
- 17 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Convolutional Neural Network Classification for Machine Tool Wear Based on Unsupervised Gaussian Mixture Model
In today's manufacturing industry it is of great importance to know the condition of a tool as it wears out. This knowledge allows us to reduce possible errors and failures in the manufacturing process. This work focuses on classifying the level of wear of a machine tool, allowing us to know its current state using measurements of forces and accelerations. First, tool wear levels are obtained by unsupervised learning (through the Gaussian mixture model). Then a convolutional neural network trained directly using the measured time series predicts the level of tool wear. After careful selection of the optimal window length, optimization algorithm, and number of epochs, wear levels were predicted with accuracy greater than 85%.
- 17 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Convolutional Neural Network Classification for Machine Tool Wear Based on Unsupervised Gaussian Mixture Model
In today's manufacturing industry it is of great importance to know the condition of a tool as it wears out. This knowledge allows us to reduce possible errors and failures in the manufacturing process. This work focuses on classifying the level of wear of a machine tool, allowing us to know its current state using measurements of forces and accelerations. First, tool wear levels are obtained by unsupervised learning (through the Gaussian mixture model). Then a convolutional neural network trained directly using the measured time series predicts the level of tool wear. After careful selection of the optimal window length, optimization algorithm, and number of epochs, wear levels were predicted with accuracy greater than 85%.
- 27 October 2021
- Published by Springer Nature in Production Engineering
- Vol. 16 (4) , 465-480
Tool wear and remaining useful life (RUL) prediction based on reduced feature set and Bayesian hyperparameter optimization
- 27 October 2021
- Published by Springer Nature in Production Engineering
- Vol. 16 (4) , 465-480
Tool wear and remaining useful life (RUL) prediction based on reduced feature set and Bayesian hyperparameter optimization
- 1 April 2019
- Published by Elsevier in Applied Thermal Engineering
- Vol. 152, 1-12
Thermoeconomic and environmental analysis and optimization of the supercritical cycle integration in a simple cycle power plant- 1 April 2019
- Published by Elsevier in Applied Thermal Engineering
- Vol. 152, 1-12
Thermoeconomic and environmental analysis and optimization of the supercritical cycle integration in a simple cycle power plant- 1 October 2017
- Published by Elsevier in Energy Conversion and Management
- Vol. 149, 1096-1108
Thermodynamic simulation model for predicting the performance of spark ignition engines using biogas as fuel
- 1 October 2017
- Published by Elsevier in Energy Conversion and Management
- Vol. 149, 1096-1108
Thermodynamic simulation model for predicting the performance of spark ignition engines using biogas as fuel
- 30 September 2017
- Published by Springer Nature in Mechanisms and Machine Science
- p. 305-314
Comparative Study of Autonomous Aerial Navigation Methods Oriented to Environmental Monitoring
- 30 September 2017
- Published by Springer Nature in Mechanisms and Machine Science
- p. 305-314
Comparative Study of Autonomous Aerial Navigation Methods Oriented to Environmental Monitoring