Jesuino Takachi Tomita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jesuino Takachi Tomita has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Cleverson Bringhenti
Aeronautics Institute of Technology—ITA, São José dos Campos 12228-900, SP, Brazil
55 shared publications João Roberto Barbosa
Inst Tecnol Aeronaut, Dept Ciencia Tecnol & Aeroespacial, Div Engn Aeronaut & Mecan, Sao Jose Dos Campos, SP, Brazil
9 shared publications- Luiz Henrique Lindquist Whitacker
Turbomachines Department, Aeronautics Institute of Technology, São José dos Campos 12228-900, SP, Brazil
6 shared publications - Ruben Bruno Diaz
Aeronautics Institute of Technology, São José dos Campos 12228-900, Brazil
6 shared publications - Franco Jefferds dos Santos Silva
Aeronautics Institute of Technology (ITA), So Jos dos Campos, São Paulo, Brazil
5 shared publications - Gustavo Bonolo de Campos
Department of Turbomachines, Aeronautic Institute of Technology, 12228-900 São José dos Campos/SP, Brazil
5 shared publications
Latest Publications
- Open Access
- 24 June 2026
- Published by MDPI AG in Preprints.org
The Effects of Axial Slots with Radial Skew Angles on the Performance and Stall Margins in a Transonic Multi-Stage Axial Compressor
In the present study, three-dimensional steady-state Reynolds-Averaged Navier–Stokes (RANS) simulations were performed to investigate the influence of radial skew angle in axial slot casing treatments (CTs) applied to the first rotor of a transonic three-and-a-half-stage axial compressor. The investigation focuses on three skewed slot configurations with radial skew angles of 35°, 45°, and 60°, while the axially aligned slot configuration (0° skew angle), previously reported and validated, is adopted solely as a reference baseline. All configurations share identical geometric proportions, enabling the isolated assessment of skew-angle effects on compressor aerodynamic behavior. The results demonstrate that the radial skew angle significantly influences the balance between stall margin improvement and efficiency variation, with the magnitude of these effects strongly dependent on operating speed. Under off-design operating conditions, skewed axial slots provide substantial stall margin enhancement relative to the smooth casing configuration, with larger skew angles generally yielding greater improvements in compressor stability. Conversely, at the design speed, increasing skew angle is associated with a progressive efficiency penalty, highlighting the trade-off between aerodynamic stability enhancement and additional aerodynamic losses. Among the skewed configurations investigated, the 45° radial skew angle provides the most favorable compromise, delivering consistent stall margin improvement across the examined operating range while preserving compressor efficiency under nominal operating conditions. Overall, the present study demonstrates that radial skew angle constitutes a critical design parameter for axial slot casing treatments in multistage compressors and should therefore be carefully tailored to the intended operating regime. The findings extend the current understanding of axial-slot flow-control mechanisms and provide practical guidance for the aerodynamic design of casing treatments in transonic axial compressors.
- 24 June 2026
- Published by MDPI AG in Preprints.org
Open AccessThe Effects of Axial Slots with Radial Skew Angles on the Performance and Stall Margins in a Transonic Multi-Stage Axial Compressor
In the present study, three-dimensional steady-state Reynolds-Averaged Navier–Stokes (RANS) simulations were performed to investigate the influence of radial skew angle in axial slot casing treatments (CTs) applied to the first rotor of a transonic three-and-a-half-stage axial compressor. The investigation focuses on three skewed slot configurations with radial skew angles of 35°, 45°, and 60°, while the axially aligned slot configuration (0° skew angle), previously reported and validated, is adopted solely as a reference baseline. All configurations share identical geometric proportions, enabling the isolated assessment of skew-angle effects on compressor aerodynamic behavior. The results demonstrate that the radial skew angle significantly influences the balance between stall margin improvement and efficiency variation, with the magnitude of these effects strongly dependent on operating speed. Under off-design operating conditions, skewed axial slots provide substantial stall margin enhancement relative to the smooth casing configuration, with larger skew angles generally yielding greater improvements in compressor stability. Conversely, at the design speed, increasing skew angle is associated with a progressive efficiency penalty, highlighting the trade-off between aerodynamic stability enhancement and additional aerodynamic losses. Among the skewed configurations investigated, the 45° radial skew angle provides the most favorable compromise, delivering consistent stall margin improvement across the examined operating range while preserving compressor efficiency under nominal operating conditions. Overall, the present study demonstrates that radial skew angle constitutes a critical design parameter for axial slot casing treatments in multistage compressors and should therefore be carefully tailored to the intended operating regime. The findings extend the current understanding of axial-slot flow-control mechanisms and provide practical guidance for the aerodynamic design of casing treatments in transonic axial compressors.
- Open Access
- 20 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. PP (00189251) , 1-24
Performance Analysis of Hybrid-Electric Propulsion Systems for Regional Commuter Aircraft
Aviation plays a fundamental and valuable role in the modern world, yet it faces significant challenges, including high fuel costs and substantial environmental pollution. These issues have prompted the aviation industry to establish emission standards and develop less-polluting propulsion systems, such as those utilizing synthetic fuels, fuel cells, and electrification. Among these, electrification holds promise as a potential solution for reducing emissions in commuter aircraft, despite the mass limitations posed by batteries. In this study, a methodology was developed and implemented within in-house software to simulate the performance of a commuter aircraft with a hybrid-electric propulsion system. The analysis focused on key metrics like fuel economy and climb time to cruise altitude. The EMB-120 Brasilia was chosen as the base aircraft for this research. Its long-standing use by the Brazilian Air Force (FAB), the authors' extensive familiarity with its performance, and the availability of experimental data for lift and drag coefficients made it an ideal model for our simulations. To evaluate the performance of the hybrid propulsion system and compare it with the standard case, a gas turbine was utilized as the primary engine. Mathematical models were developed for the PW118 gas turbine, which powers the real aircraft that was considered the standard case, and for the PT6A-68C, which was suggested as a substitute for the hybrid system. To evaluate the aircraft's performance, a standard mission was simulated on a short-range route of 926 km (500 NM), flying at an altitude of 7,620 m (25,000 ft), a common mission that is used by Brazilian Air Force. For hybrid simulations, battery packs were tested with specific energies ranging from 0.125 kWh/kg to 0.750 kWh/kg, in multiples of the initial value. Batteries with 0.250 kWh/kg were considered the current state-of-the-art, while the 0.750 kWh/kg packs represent an extreme upper bound associated with far-future technological developments. The results demonstrated significant performance gains depending on the chosen battery technology and the power split, the hybrid system achieved fuel savings of up to 18% to 19% and reduced climb time by 17% to 25%.
- 20 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. PP (00189251) , 1-24
Open AccessPerformance Analysis of Hybrid-Electric Propulsion Systems for Regional Commuter Aircraft
Aviation plays a fundamental and valuable role in the modern world, yet it faces significant challenges, including high fuel costs and substantial environmental pollution. These issues have prompted the aviation industry to establish emission standards and develop less-polluting propulsion systems, such as those utilizing synthetic fuels, fuel cells, and electrification. Among these, electrification holds promise as a potential solution for reducing emissions in commuter aircraft, despite the mass limitations posed by batteries. In this study, a methodology was developed and implemented within in-house software to simulate the performance of a commuter aircraft with a hybrid-electric propulsion system. The analysis focused on key metrics like fuel economy and climb time to cruise altitude. The EMB-120 Brasilia was chosen as the base aircraft for this research. Its long-standing use by the Brazilian Air Force (FAB), the authors' extensive familiarity with its performance, and the availability of experimental data for lift and drag coefficients made it an ideal model for our simulations. To evaluate the performance of the hybrid propulsion system and compare it with the standard case, a gas turbine was utilized as the primary engine. Mathematical models were developed for the PW118 gas turbine, which powers the real aircraft that was considered the standard case, and for the PT6A-68C, which was suggested as a substitute for the hybrid system. To evaluate the aircraft's performance, a standard mission was simulated on a short-range route of 926 km (500 NM), flying at an altitude of 7,620 m (25,000 ft), a common mission that is used by Brazilian Air Force. For hybrid simulations, battery packs were tested with specific energies ranging from 0.125 kWh/kg to 0.750 kWh/kg, in multiples of the initial value. Batteries with 0.250 kWh/kg were considered the current state-of-the-art, while the 0.750 kWh/kg packs represent an extreme upper bound associated with far-future technological developments. The results demonstrated significant performance gains depending on the chosen battery technology and the power split, the hybrid system achieved fuel savings of up to 18% to 19% and reduced climb time by 17% to 25%.
- Open Access
High-Pressure Turbine Aerodynamic Enhancement Using Rotor Tip Desensitization Technique
Turbines experience pressure losses from various sources, one of which is the tip leakage flow in the rotor blades. This is one of the main factors responsible for the decrease in turbine efficiency. This leakage is caused by pressure differences between the blade pressure and suction sides. High-pressure turbines with low aspect ratios and high-pressure loading face critical tip clearance losses, impacting turbine performance. One way to reduce tip leakage flow is to apply the desensitization technique to modify the rotor blade tip geometry. This study aims to apply the desensitization technique to the Energy-Efficient Engine developed by NASA. Different Winglet geometries with varying extensions along the blade tip chord (A—, B—, and C—), three types of Squealers with different rim dimensions and cavity heights (Squealer A and B), and the same rim thickness and cavity height of Squealer A with a decreased trailing edge region down to (Squealer C) were numerically tested. Additionally, the study simulates blending Winglet A with Squealer A (Squealer–Winglet A), Squealer A with Winglet B (Squealer–Winglet B), and Winglet A with Squealer B (Squealer–Winglet C). Numerical simulations are conducted and compared with experimental data. Comparing the various geometries at the design-point pressure ratio, the Winglet A configuration demonstrates an increase of in efficiency, Squealer C an increase of , and for cases involving all Squealer–Winglet models, no improvement was obtained. For N at the design-point pressure ratio, Winglet B demonstrates an increase of in efficiency, Squealer C an increase of , and Squealer–Winglet A an increase of . These are interesting results in the case of the engine operating at cruise condition, in which the rotational speed is around N.Open AccessHigh-Pressure Turbine Aerodynamic Enhancement Using Rotor Tip Desensitization Technique
Turbines experience pressure losses from various sources, one of which is the tip leakage flow in the rotor blades. This is one of the main factors responsible for the decrease in turbine efficiency. This leakage is caused by pressure differences between the blade pressure and suction sides. High-pressure turbines with low aspect ratios and high-pressure loading face critical tip clearance losses, impacting turbine performance. One way to reduce tip leakage flow is to apply the desensitization technique to modify the rotor blade tip geometry. This study aims to apply the desensitization technique to the Energy-Efficient Engine developed by NASA. Different Winglet geometries with varying extensions along the blade tip chord (A—, B—, and C—), three types of Squealers with different rim dimensions and cavity heights (Squealer A and B), and the same rim thickness and cavity height of Squealer A with a decreased trailing edge region down to (Squealer C) were numerically tested. Additionally, the study simulates blending Winglet A with Squealer A (Squealer–Winglet A), Squealer A with Winglet B (Squealer–Winglet B), and Winglet A with Squealer B (Squealer–Winglet C). Numerical simulations are conducted and compared with experimental data. Comparing the various geometries at the design-point pressure ratio, the Winglet A configuration demonstrates an increase of in efficiency, Squealer C an increase of , and for cases involving all Squealer–Winglet models, no improvement was obtained. For N at the design-point pressure ratio, Winglet B demonstrates an increase of in efficiency, Squealer C an increase of , and Squealer–Winglet A an increase of . These are interesting results in the case of the engine operating at cruise condition, in which the rotational speed is around N. - Open Access
- 16 September 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 176
A review of hydrogen aircraft propulsion systems: recent advances and environmental perspectives
- 16 September 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 176
Open AccessA review of hydrogen aircraft propulsion systems: recent advances and environmental perspectives
- Open Access
Performance and Stall Margin Evaluation of Axial Slot Casing Treatment in a Transonic Multistage Compressor
Adverse pressure gradients are intrinsic to compressor flow behavior and are further intensified by secondary effects associated with rotor tip clearance flow interactions. Tip clearance generates leakage flow, which leads to the formation of tip leakage vortices, a major contributor to aerodynamic losses in axial compressors. These vortices significantly influence both compressor performance and operational stability. Extensive prior research has demonstrated that passive casing treatments, particularly axial slots, can substantially improve the stall margin in axial compressors. In this work, the performance of a new casing treatment geometry is investigated using the concept of recirculating flow within semi-circular axial slots. The proposed casing treatment geometry builds upon recent experimental findings involving single-rotor configurations. It was applied to the first rotor row of a three-and-a-half-stage (3.5-stage) axial compressor comprising an inlet guide vane followed by three rotor–stator stages. The numerical model incorporates axial slots with a novel periodic interface approach implemented in a multistage compressor simulation. Three-dimensional steady-state RANS (Reynolds Average Navier-Stokes) simulations were performed to investigate the aerodynamic effects of the casing treatment across various rotational speeds. The results for the casing treatment configuration were compared with those of a baseline smooth casing. The introduction of the new casing treatment produced noticeable modifications to the internal flow structure, particularly in the tip region, resulting in improved overall compressor stability within the operating range of 85 to 100% of design speed.
Open AccessPerformance and Stall Margin Evaluation of Axial Slot Casing Treatment in a Transonic Multistage Compressor
Adverse pressure gradients are intrinsic to compressor flow behavior and are further intensified by secondary effects associated with rotor tip clearance flow interactions. Tip clearance generates leakage flow, which leads to the formation of tip leakage vortices, a major contributor to aerodynamic losses in axial compressors. These vortices significantly influence both compressor performance and operational stability. Extensive prior research has demonstrated that passive casing treatments, particularly axial slots, can substantially improve the stall margin in axial compressors. In this work, the performance of a new casing treatment geometry is investigated using the concept of recirculating flow within semi-circular axial slots. The proposed casing treatment geometry builds upon recent experimental findings involving single-rotor configurations. It was applied to the first rotor row of a three-and-a-half-stage (3.5-stage) axial compressor comprising an inlet guide vane followed by three rotor–stator stages. The numerical model incorporates axial slots with a novel periodic interface approach implemented in a multistage compressor simulation. Three-dimensional steady-state RANS (Reynolds Average Navier-Stokes) simulations were performed to investigate the aerodynamic effects of the casing treatment across various rotational speeds. The results for the casing treatment configuration were compared with those of a baseline smooth casing. The introduction of the new casing treatment produced noticeable modifications to the internal flow structure, particularly in the tip region, resulting in improved overall compressor stability within the operating range of 85 to 100% of design speed.
- Open Access
- 4 August 2025
- Published by MDPI AG in Preprints.org
Performance and Stall Margin Evaluation of Axial Slot Casing Treatment in a Transonic Multistage Compressor
Adverse pressure gradients are intrinsic to the flow behavior in compressors and are further ex-acerbated by secondary effects arising from rotor tip clearance flow interactions, a phenomenon common across various turbomachinery configurations, axial and radial. Tip clearance induces leakage flow, which leads to the formation of tip leakage vortices—a principal contributor to aerodynamic losses in axial compressors. These vortices exert a significant impact on both com-pressor performance and the operational stability range. Extensive prior research has demon-strated that passive casing treatments, particularly the implementation of axial slots, can sub-stantially enhance stall margin in axial compressors. The recirculating flow established within semi-circular axial slots acts to mitigate the strength of the tip leakage vortex by redirecting low-momentum leakage flow upstream of the rotor leading edge, thereby introducing a resistance mechanism that suppresses flow leakage through the clearance gap. Many existing studies on axial slot implementation focus predominantly on high-performance single-stage axial compressors. Consequently, there remains a gap in the literature regarding the application and performance implications of such treatments in multi-stage compressor systems. In the present study, a passive casing treatment employing axial slots was integrated into a multi-stage axial compressor. The slot geometry was selected based on recent experimental findings involving single-rotor configura-tions. The casing treatment was applied over the first rotor row in a three-and-a-half-stage (3.5-stage) axial compressor configuration, comprising an inlet guide vane (IGV) followed by three rotor-stator stages. Three-dimensional steady-state numerical simulations were conducted to investigate the aerodynamic effects of the axial slot treatment across various rotational speeds. The results obtained for the slotted configuration were compared against a baseline case featuring a smooth casing. The introduction of axial slots induced noticeable modifications to the internal flow structure, particularly in the tip region, leading to an improvement in overall compressor stability within the operating range between 85% to 100% of design speed. Stall margins improved 3.55% at design speed. Significant stall margin improvement occurred at 95% design speed with ΔSM of 11.24%. At 85% design speed, the efficiency starts to deteriorate and axial slots did not improve the stall margins with ΔSM of -1.03 %.
- 4 August 2025
- Published by MDPI AG in Preprints.org
Open AccessPerformance and Stall Margin Evaluation of Axial Slot Casing Treatment in a Transonic Multistage Compressor
Adverse pressure gradients are intrinsic to the flow behavior in compressors and are further ex-acerbated by secondary effects arising from rotor tip clearance flow interactions, a phenomenon common across various turbomachinery configurations, axial and radial. Tip clearance induces leakage flow, which leads to the formation of tip leakage vortices—a principal contributor to aerodynamic losses in axial compressors. These vortices exert a significant impact on both com-pressor performance and the operational stability range. Extensive prior research has demon-strated that passive casing treatments, particularly the implementation of axial slots, can sub-stantially enhance stall margin in axial compressors. The recirculating flow established within semi-circular axial slots acts to mitigate the strength of the tip leakage vortex by redirecting low-momentum leakage flow upstream of the rotor leading edge, thereby introducing a resistance mechanism that suppresses flow leakage through the clearance gap. Many existing studies on axial slot implementation focus predominantly on high-performance single-stage axial compressors. Consequently, there remains a gap in the literature regarding the application and performance implications of such treatments in multi-stage compressor systems. In the present study, a passive casing treatment employing axial slots was integrated into a multi-stage axial compressor. The slot geometry was selected based on recent experimental findings involving single-rotor configura-tions. The casing treatment was applied over the first rotor row in a three-and-a-half-stage (3.5-stage) axial compressor configuration, comprising an inlet guide vane (IGV) followed by three rotor-stator stages. Three-dimensional steady-state numerical simulations were conducted to investigate the aerodynamic effects of the axial slot treatment across various rotational speeds. The results obtained for the slotted configuration were compared against a baseline case featuring a smooth casing. The introduction of axial slots induced noticeable modifications to the internal flow structure, particularly in the tip region, leading to an improvement in overall compressor stability within the operating range between 85% to 100% of design speed. Stall margins improved 3.55% at design speed. Significant stall margin improvement occurred at 95% design speed with ΔSM of 11.24%. At 85% design speed, the efficiency starts to deteriorate and axial slots did not improve the stall margins with ΔSM of -1.03 %.
- Open Access
Winglet Geometries Applied to Rotor Blades of a Hydraulic Axial Turbine Used as a Turbopump: A Parametric Analysis
Turbines are rotating machines that generate power by the expansion of a fluid; due to their characteristics, these turbomachines are widely applied in aerospace propulsion systems. Due to the clearance between the rotor blade tip and casing, there is a leakage flow from the blade pressure to the suction sides, which generates energy loss. There are different strategies that can be applied to avoid part of this loss; one of them is the application of so-called desensitization techniques. The application of these techniques on gas turbines has been widely evaluated; however, there is a lack of analyses of hydraulic turbines. This study is a continuation of earlier analyses conducted during the first stage of the hydraulic axial turbine used in the low-pressure oxidizer turbopump (LPOTP) of the space shuttle main engine (SSME). The previous work analyzed the application of squealer geometries at the rotor tip. In the present paper, winglet geometry techniques are investigated based on three-dimensional flowfield calculations. The commercial CFX v.19.2 and ICEM v.19.2 software were used, respectively, on the numerical simulations and computational mesh generation. Experimental results published by the National Aeronautics and Space Administration (NASA) and data from previous works were used on the computational model validation. The parametric analysis was conducted by varying the thickness and width of the winglet. The results obtained show that by increasing the winglet thickness, the stage efficiency is also increased. However, the geometric dimension of its width has minimal impact on this result. An average efficiency increase of 2.0% was observed across the entire turbine operational range. In the case of the squealer, for the design point, the maximum efficiency improvement was 1.62%, compared to the current improvement of 2.23% using the winglet desensitization technique. It was found that the proposed geometries application also changes the cavitation occurrence along the stage, which is a relevant result, since it can impact the turbine life cycle.
Open AccessWinglet Geometries Applied to Rotor Blades of a Hydraulic Axial Turbine Used as a Turbopump: A Parametric Analysis
Turbines are rotating machines that generate power by the expansion of a fluid; due to their characteristics, these turbomachines are widely applied in aerospace propulsion systems. Due to the clearance between the rotor blade tip and casing, there is a leakage flow from the blade pressure to the suction sides, which generates energy loss. There are different strategies that can be applied to avoid part of this loss; one of them is the application of so-called desensitization techniques. The application of these techniques on gas turbines has been widely evaluated; however, there is a lack of analyses of hydraulic turbines. This study is a continuation of earlier analyses conducted during the first stage of the hydraulic axial turbine used in the low-pressure oxidizer turbopump (LPOTP) of the space shuttle main engine (SSME). The previous work analyzed the application of squealer geometries at the rotor tip. In the present paper, winglet geometry techniques are investigated based on three-dimensional flowfield calculations. The commercial CFX v.19.2 and ICEM v.19.2 software were used, respectively, on the numerical simulations and computational mesh generation. Experimental results published by the National Aeronautics and Space Administration (NASA) and data from previous works were used on the computational model validation. The parametric analysis was conducted by varying the thickness and width of the winglet. The results obtained show that by increasing the winglet thickness, the stage efficiency is also increased. However, the geometric dimension of its width has minimal impact on this result. An average efficiency increase of 2.0% was observed across the entire turbine operational range. In the case of the squealer, for the design point, the maximum efficiency improvement was 1.62%, compared to the current improvement of 2.23% using the winglet desensitization technique. It was found that the proposed geometries application also changes the cavitation occurrence along the stage, which is a relevant result, since it can impact the turbine life cycle.
- Open Access
- 12 March 2025
- Published by MDPI AG in Preprints.org
Winglet Geometries Applied in Rotor Blades of a Hydraulic Axial Turbine Used as Turbopump: A Parametric Analysis
Turbines are rotating machines that generate power by the expansion of a fluid; due to their characteristic these turbomachines are widely applied in the aerospace propulsion systems. Since due to the clearance between rotor blade tip and casing, there is a leakage flow from blade pressure to suction sides, which generates an energy loss. There are different strategies that can be applied to avoid part of this loss, one of them is by the application of the called desensitization techniques. The application of these techniques on gas turbines have been widely evaluated, however, there is a lack of these analyzes for hydraulic turbines. This work is a sequence of previous analyzes developed for the first stage of the hydraulic axial turbine used on the Space Shuttle Main Engine (SSME) Low Pressure Oxidizer Turbopump (LPOTP). The last work analyzed the application of squealer geometries at rotor tip. In the present paper, the winglet geometry techniques were investigated based on three-dimensional flowfield calculation. The commercial CFX v.19.2 and ICEM v.19.2 software were used, respectively, on the numerical simulations and computational meshes generation. Experimental results published by the National Aeronautics and Space Administration (NASA), and data from previous works, were used on the computational model validation. The parametric analysis was done by the variation in the winglet thickness and width. The results obtained shown that increasing the winglet thickness, the stage efficiency is also increased. However, its width geometrical dimension almost does not impact this result. It was verified an efficiency increase of 2.0%, over the entire turbine operational range. It was found that the proposed geometries application also changes the cavitation occurrence along the stage, which is a relevant result, since it can impact the turbine life cycle.
- 12 March 2025
- Published by MDPI AG in Preprints.org
Open AccessWinglet Geometries Applied in Rotor Blades of a Hydraulic Axial Turbine Used as Turbopump: A Parametric Analysis
Turbines are rotating machines that generate power by the expansion of a fluid; due to their characteristic these turbomachines are widely applied in the aerospace propulsion systems. Since due to the clearance between rotor blade tip and casing, there is a leakage flow from blade pressure to suction sides, which generates an energy loss. There are different strategies that can be applied to avoid part of this loss, one of them is by the application of the called desensitization techniques. The application of these techniques on gas turbines have been widely evaluated, however, there is a lack of these analyzes for hydraulic turbines. This work is a sequence of previous analyzes developed for the first stage of the hydraulic axial turbine used on the Space Shuttle Main Engine (SSME) Low Pressure Oxidizer Turbopump (LPOTP). The last work analyzed the application of squealer geometries at rotor tip. In the present paper, the winglet geometry techniques were investigated based on three-dimensional flowfield calculation. The commercial CFX v.19.2 and ICEM v.19.2 software were used, respectively, on the numerical simulations and computational meshes generation. Experimental results published by the National Aeronautics and Space Administration (NASA), and data from previous works, were used on the computational model validation. The parametric analysis was done by the variation in the winglet thickness and width. The results obtained shown that increasing the winglet thickness, the stage efficiency is also increased. However, its width geometrical dimension almost does not impact this result. It was verified an efficiency increase of 2.0%, over the entire turbine operational range. It was found that the proposed geometries application also changes the cavitation occurrence along the stage, which is a relevant result, since it can impact the turbine life cycle.
- Open Access
An Evaluation of Passive Wall Treatment with Circumferential Grooves at the Casing of the First and Second Blade Rotor Rows of a High-Performance Multi-Stage Axial Compressor
The internal losses in the tip clearance region strongly influence the compressor performance and its operational range. Previous research proved that passive wall treatments with circumferential grooves in axial compressors effectively increase the compressor stall margin. The vortex generated inside the circumferential grooves creates a resistance to the flow that leaks into the tip clearance region of the compressor. However, most works found in the literature on circumferential grooves in axial compressors deal only with high-performance single-stage axial compressors. Therefore, there is a need to investigate and analyze the behavior of circumferential grooves in a multi-stage environment. In the present work, a passive wall treatment with circumferential grooves was implemented in a multi-stage axial compressor. Different configurations of circumferential grooves were created at the casing of the first and second rotor rows used in a four-stage axial flow compressor. Numerical simulations were performed to evaluate the influence of the circumferential grooves on the performance of a multi-stage axial compressor. The results obtained after the simulations for the different circumferential groove configurations were compared with the results obtained for the compressor without casing treatment (smooth wall) for different rotational speeds. Furthermore, the complete compressor map characteristics were simulated for the different casing treatment configurations, and the results were compared with the compressor characteristics of the smooth wall case. The passive wall treatment with circumferential grooves produced changes in the multi-stage axial compressor flow field, especially in the tip clearance region, improving the compressor stability mainly for part load speeds.
Open AccessAn Evaluation of Passive Wall Treatment with Circumferential Grooves at the Casing of the First and Second Blade Rotor Rows of a High-Performance Multi-Stage Axial Compressor
The internal losses in the tip clearance region strongly influence the compressor performance and its operational range. Previous research proved that passive wall treatments with circumferential grooves in axial compressors effectively increase the compressor stall margin. The vortex generated inside the circumferential grooves creates a resistance to the flow that leaks into the tip clearance region of the compressor. However, most works found in the literature on circumferential grooves in axial compressors deal only with high-performance single-stage axial compressors. Therefore, there is a need to investigate and analyze the behavior of circumferential grooves in a multi-stage environment. In the present work, a passive wall treatment with circumferential grooves was implemented in a multi-stage axial compressor. Different configurations of circumferential grooves were created at the casing of the first and second rotor rows used in a four-stage axial flow compressor. Numerical simulations were performed to evaluate the influence of the circumferential grooves on the performance of a multi-stage axial compressor. The results obtained after the simulations for the different circumferential groove configurations were compared with the results obtained for the compressor without casing treatment (smooth wall) for different rotational speeds. Furthermore, the complete compressor map characteristics were simulated for the different casing treatment configurations, and the results were compared with the compressor characteristics of the smooth wall case. The passive wall treatment with circumferential grooves produced changes in the multi-stage axial compressor flow field, especially in the tip clearance region, improving the compressor stability mainly for part load speeds.
- 10 February 2023
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 15 (4) , 1-29
Modeling an Evaporative Cooling System to Improve Gas Turbines Performance
Evaporative cooling systems are commonly used in thermoelectric plants to cool the air at gas turbines inlet, improving the performance of these engines. Normally, the evaporative cooling is modeled as adiabatic saturation and, in this case, the water-air equilibrium temperature depends only on the atmospheric air properties. However, other factors such as the water temperature that supplies the equipment and the ratio between the mass flow rates of water and air, also affect the equilibrium conditions of these systems. This work presents three methodologies to calculate the air temperature in equilibrium state, considering all the factors mentioned. The methodologies were implemented in a computer program written in fortran. In all cases tested, the results obtained by the three models showed high convergence. As an example, for 70 different sets of inputs, the absolute and relative differences of the results were below 0.3236 °C and 1.2480%, respectively. A statistical study, also on this sample of results, revealed that, for a confidence level of 99%, the hypothesis of the equivalence between the methods cannot be rejected.
- 10 February 2023
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 15 (4) , 1-29
Modeling an Evaporative Cooling System to Improve Gas Turbines Performance
Evaporative cooling systems are commonly used in thermoelectric plants to cool the air at gas turbines inlet, improving the performance of these engines. Normally, the evaporative cooling is modeled as adiabatic saturation and, in this case, the water-air equilibrium temperature depends only on the atmospheric air properties. However, other factors such as the water temperature that supplies the equipment and the ratio between the mass flow rates of water and air, also affect the equilibrium conditions of these systems. This work presents three methodologies to calculate the air temperature in equilibrium state, considering all the factors mentioned. The methodologies were implemented in a computer program written in fortran. In all cases tested, the results obtained by the three models showed high convergence. As an example, for 70 different sets of inputs, the absolute and relative differences of the results were below 0.3236 °C and 1.2480%, respectively. A statistical study, also on this sample of results, revealed that, for a confidence level of 99%, the hypothesis of the equivalence between the methods cannot be rejected.