Christopher A. Hone
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Christopher A. Hone has a total of 90 co-authors. Here are the top co-authors by number of shared publications:
- C. Oliver Kappe
Institute of Chemistry, University of Graz, NAWI Graz, Heinrichstrasse 28, 8010 Graz, Austria
32 shared publications - Dominik Polterauer
Center for Continuous Flow Synthesis and Processing (CCFLOW), Research Center Pharmaceutical Engineering GmbH (RCPE), Inffeldgasse 13, Graz 8010, Austria
5 shared publications - Jason D. Williams
Center for Continuous Synthesis and Processing (CCFLOW), Research Center Pharmaceutical Engineering GmbH (RCPE), Inffeldgasse 13, 8010 Graz, Austria
5 shared publications - Peter Sagmeister
Massachusetts Institute of Technology 77 Massachusetts Avenue
5 shared publications Dominique M. Roberge
Advanced Chemistry Technologies, Lonza AG, Visp CH-3930, Switzerland
4 shared publicationsKevin Leslie
Chemical Development, Pharmaceutical Technology & Development, Operations, AstraZeneca, Macclesfield, UK
4 shared publications
Latest Publications
- Open Access
- 5 January 2026
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 11 (4) , 922-931
Indirect hard modeling of low resolution benchtop NMR data for the kinetic fitting of a complex organic reaction
A benchtop NMR instrument in combination with spectral hard modeling enabled monitoring and subsequent kinetic fitting of a chlorination reaction. Different modes were investigated, an NMR tube, re-circulating batch and single pass continuous flow.
- 5 January 2026
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 11 (4) , 922-931
Open AccessIndirect hard modeling of low resolution benchtop NMR data for the kinetic fitting of a complex organic reaction
A benchtop NMR instrument in combination with spectral hard modeling enabled monitoring and subsequent kinetic fitting of a chlorination reaction. Different modes were investigated, an NMR tube, re-circulating batch and single pass continuous flow.
- Open Access
- 3 December 2025
- Published by Royal Society of Chemistry (RSC) in Chemical Science
- Vol. 16 (47) , 22447-22455
Leveraging an intelligent slug flow platform for self-optimization of reaction systems with categorical variables
Using a liquid handler, categorical variables have been investigated in self-optimization. We use an autonomous closed-loop platform to demonstrate a method to encode categorical variables based on simple, physical chemistry-based relationships.
- 3 December 2025
- Published by Royal Society of Chemistry (RSC) in Chemical Science
- Vol. 16 (47) , 22447-22455
Open AccessLeveraging an intelligent slug flow platform for self-optimization of reaction systems with categorical variables
Using a liquid handler, categorical variables have been investigated in self-optimization. We use an autonomous closed-loop platform to demonstrate a method to encode categorical variables based on simple, physical chemistry-based relationships.
- Open Access
- 11 September 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (40) , 33278-33296
FlowMat: a toolbox for modeling flow reactors using physics-based and machine learning approaches for modular simulation, parameter identification, and reactor optimization
This paper introduces a versatile, open-source MATLAB/Simulink toolbox for modeling and optimizing flow reactors. The toolbox features a modular architecture and an intuitive drag-and-drop interface, supporting a range of different modeling approaches, including physics-based, data-driven, and hybrid models such as physics-informed neural networks. We detail the toolbox's implementation and demonstrate its capabilities through real-world applications, including the simulation of flow reactors, identification of reaction parameters using experimental data (e.g., transient data), and optimization of reactor operating points and configurations. Experimental validations illustrate the practical applicability and effectiveness of the toolbox, making it a valuable resource for researchers and engineers in the field with the potential of reducing the cost and time required for parameter determination and reactor optimization.
- 11 September 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (40) , 33278-33296
Open AccessFlowMat: a toolbox for modeling flow reactors using physics-based and machine learning approaches for modular simulation, parameter identification, and reactor optimization
This paper introduces a versatile, open-source MATLAB/Simulink toolbox for modeling and optimizing flow reactors. The toolbox features a modular architecture and an intuitive drag-and-drop interface, supporting a range of different modeling approaches, including physics-based, data-driven, and hybrid models such as physics-informed neural networks. We detail the toolbox's implementation and demonstrate its capabilities through real-world applications, including the simulation of flow reactors, identification of reaction parameters using experimental data (e.g., transient data), and optimization of reactor operating points and configurations. Experimental validations illustrate the practical applicability and effectiveness of the toolbox, making it a valuable resource for researchers and engineers in the field with the potential of reducing the cost and time required for parameter determination and reactor optimization.
- Open Access
- 5 September 2025
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 10 (12) , 2932-2946
Neural tanks-in-series: a physics-guided neural network extension of the tanks-in-series model for enhanced flow reactor and reaction modelling
This paper introduces the neural tanks-in-series (NTiS) model, an extension of the traditional tanks-in-series (TiS) model using physics-guided neural networks (PGNNs).
- 5 September 2025
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 10 (12) , 2932-2946
Open AccessNeural tanks-in-series: a physics-guided neural network extension of the tanks-in-series model for enhanced flow reactor and reaction modelling
This paper introduces the neural tanks-in-series (NTiS) model, an extension of the traditional tanks-in-series (TiS) model using physics-guided neural networks (PGNNs).
- Open Access
- 15 May 2025
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 27 (23) , 6787-6795
Two-step continuous flow aerobic oxidation of cannabidiol to cannabinoquinone derivatives
A two-step continuous flow oxidation procedure is presented for the preparation of Etrinabdione, a cannabidiol quinone derivative. Etrinabdione is currently undergoing clinical trials for the treatment of peripheral artery disease. Both steps described herein utilize molecular oxygen as a green and inexpensive stoichiometric oxidant. Initially, the two-steps were optimized separately. The first step is a very fast oxidation process to form quinonoid derivative HU-331 and includes an in situ quench for the safe handling of peroxy intermediates. The second step is a segmented flow oxidative amination to afford Etrinabdione. The two steps can be run either separately or telescoped by incorporating a gravity-based continuous separation. The two steps were telescoped to afford Etrinabdione in 98% yield. The process mass intensity (PMI) was significantly reduced when compared to an existing batch protocol. The second step was also adapted for the preparation of two additional cannabidiol quinone analogs. The described protocol significantly improves the efficiency, safety and scalability when compared to existing batch protocols.
- 15 May 2025
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 27 (23) , 6787-6795
Open AccessTwo-step continuous flow aerobic oxidation of cannabidiol to cannabinoquinone derivatives
A two-step continuous flow oxidation procedure is presented for the preparation of Etrinabdione, a cannabidiol quinone derivative. Etrinabdione is currently undergoing clinical trials for the treatment of peripheral artery disease. Both steps described herein utilize molecular oxygen as a green and inexpensive stoichiometric oxidant. Initially, the two-steps were optimized separately. The first step is a very fast oxidation process to form quinonoid derivative HU-331 and includes an in situ quench for the safe handling of peroxy intermediates. The second step is a segmented flow oxidative amination to afford Etrinabdione. The two steps can be run either separately or telescoped by incorporating a gravity-based continuous separation. The two steps were telescoped to afford Etrinabdione in 98% yield. The process mass intensity (PMI) was significantly reduced when compared to an existing batch protocol. The second step was also adapted for the preparation of two additional cannabidiol quinone analogs. The described protocol significantly improves the efficiency, safety and scalability when compared to existing batch protocols.
- Open Access
- 17 March 2025
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 15 (9) , 2783-2793
Catalytic static mixers enable the continuous hydrogenation of cannabidiol and tetrahydrocannabinol
In this work, we investigated the catalytic hydrogenation of cannabidiol (CBD), delta-8-tetrahydrocannabinol (Δ8-THC) and delta-9-tetrahydrocannabinol (Δ9-THC) by using catalytic static mixer (CSM) technology within a shell-and-tube reactor. Hydrogenation of these compounds is typically reported in batch at milligram quantities and affords a mixture of products. We were interested in developing a robust preparative-scale synthesis of 8,9-dihydrocannabidiol (H2CBD) and tetrahydrocannabidiol (H4CBD) from CBD, and hexahydrocannabinol (HHC) from Δ8-THC and Δ9-THC. We examined the influence of different noble metal-based CSMs (Pt/alumina, Pd/alumina, Pd-electroplated and Ru/alumina) and different operating conditions on the reaction performance. Pd/alumina CSMs were found to be unsuitable due to the formation of impurities, which partly arose due to double bond isomerization. Pd-electroplated CSMs displayed very low activity. Ru/alumina CSMs were observed to undergo rapid catalyst deactivation. Pt/alumina CSMs displayed high activity and good selectivity, even though signs of deactivation were still present at temperatures higher than 80 °C. We linked this deactivation to a combined influence of internal mass transfer limitation and accumulation of adsorbed molecules on the metal surface. After a careful fine-tuning of the operating conditions over Pt/alumina CSMs, we could obtain H2CBD, H4CBD and HHC in high yield from the corresponding cannabinoid derivative. Kinetic modeling and parameter fitting were successfully performed for the hydrogenation of CBD, which incorporated catalyst deactivation. Catalytic static mixer (CSM) technology is therefore demonstrated to be an industrially viable solution for the hydrogenation of cannabinoid derivatives.
- 17 March 2025
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 15 (9) , 2783-2793
Open AccessCatalytic static mixers enable the continuous hydrogenation of cannabidiol and tetrahydrocannabinol
In this work, we investigated the catalytic hydrogenation of cannabidiol (CBD), delta-8-tetrahydrocannabinol (Δ8-THC) and delta-9-tetrahydrocannabinol (Δ9-THC) by using catalytic static mixer (CSM) technology within a shell-and-tube reactor. Hydrogenation of these compounds is typically reported in batch at milligram quantities and affords a mixture of products. We were interested in developing a robust preparative-scale synthesis of 8,9-dihydrocannabidiol (H2CBD) and tetrahydrocannabidiol (H4CBD) from CBD, and hexahydrocannabinol (HHC) from Δ8-THC and Δ9-THC. We examined the influence of different noble metal-based CSMs (Pt/alumina, Pd/alumina, Pd-electroplated and Ru/alumina) and different operating conditions on the reaction performance. Pd/alumina CSMs were found to be unsuitable due to the formation of impurities, which partly arose due to double bond isomerization. Pd-electroplated CSMs displayed very low activity. Ru/alumina CSMs were observed to undergo rapid catalyst deactivation. Pt/alumina CSMs displayed high activity and good selectivity, even though signs of deactivation were still present at temperatures higher than 80 °C. We linked this deactivation to a combined influence of internal mass transfer limitation and accumulation of adsorbed molecules on the metal surface. After a careful fine-tuning of the operating conditions over Pt/alumina CSMs, we could obtain H2CBD, H4CBD and HHC in high yield from the corresponding cannabinoid derivative. Kinetic modeling and parameter fitting were successfully performed for the hydrogenation of CBD, which incorporated catalyst deactivation. Catalytic static mixer (CSM) technology is therefore demonstrated to be an industrially viable solution for the hydrogenation of cannabinoid derivatives.
- 15 January 2025
- Published by American Chemical Society (ACS) in Organic Process Research & Development
- Vol. 29 (2) , 363-372
Can a Simple Surrogate Model System Be Used to Develop a Continuous Flow Packed Bed Hydrogenation for a Complex Molecule?
- 15 January 2025
- Published by American Chemical Society (ACS) in Organic Process Research & Development
- Vol. 29 (2) , 363-372
Can a Simple Surrogate Model System Be Used to Develop a Continuous Flow Packed Bed Hydrogenation for a Complex Molecule?
- 8 July 2024
- Published by American Chemical Society (ACS) in Organic Process Research & Development
- Vol. 28 (7) , 2919-2927
Deoxyfluorination of Ketones with Sulfur Tetrafluoride (SF4) and Dialkylamines in Continuous Flow Mode
- 8 July 2024
- Published by American Chemical Society (ACS) in Organic Process Research & Development
- Vol. 28 (7) , 2919-2927
Deoxyfluorination of Ketones with Sulfur Tetrafluoride (SF4) and Dialkylamines in Continuous Flow Mode
- 3 July 2024
- Published by American Chemical Society (ACS) in Organic Process Research & Development
- Vol. 28 (7) , 2928-2934
Design of Experiments-Based Optimization of an Electrochemical Decarboxylative Alkylation Using a Spinning Cylinder Electrode Reactor
- 3 July 2024
- Published by American Chemical Society (ACS) in Organic Process Research & Development
- Vol. 28 (7) , 2928-2934
Design of Experiments-Based Optimization of an Electrochemical Decarboxylative Alkylation Using a Spinning Cylinder Electrode Reactor
- Open Access
- 24 April 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Design of Experiments-Based Optimization of an ElectrochemicalDecarboxylative Alkylation using a Spinning Cylinder ElectrodeReactor
A design of experiments model has been developed to optimize an electrochemical protocol for the decarboxylative N-alkylation of pyrazole in a spinning cylinder electrode reactor. The electrochemical reaction requires the incorporation of molecular sieves as an additive to ensure the absence of moisture and prevent potential electrode corrosion issues. The spinning cylinder electrode reactor proved to be an idea platform to scale up this transformation, involving a suspension of solid particles, to multigram scales. The reaction model, which showed an excellent fitting with the experimental data, provided insights on the effect of important electrolysis parameters unique to this reactor design, such as the electrode spinning speed, on the reaction conversion and selectivity. Furthermore, the design of experiments also supplied optimal electrolysis parameters for this complex multivariable reaction system, resulting in full conversion of the substrate and excellent selectivity for a 600 mL volume reaction in recirculation flow mode, with 94% isolated yield for the target N-alkylated product.
- 24 April 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessDesign of Experiments-Based Optimization of an ElectrochemicalDecarboxylative Alkylation using a Spinning Cylinder ElectrodeReactor
A design of experiments model has been developed to optimize an electrochemical protocol for the decarboxylative N-alkylation of pyrazole in a spinning cylinder electrode reactor. The electrochemical reaction requires the incorporation of molecular sieves as an additive to ensure the absence of moisture and prevent potential electrode corrosion issues. The spinning cylinder electrode reactor proved to be an idea platform to scale up this transformation, involving a suspension of solid particles, to multigram scales. The reaction model, which showed an excellent fitting with the experimental data, provided insights on the effect of important electrolysis parameters unique to this reactor design, such as the electrode spinning speed, on the reaction conversion and selectivity. Furthermore, the design of experiments also supplied optimal electrolysis parameters for this complex multivariable reaction system, resulting in full conversion of the substrate and excellent selectivity for a 600 mL volume reaction in recirculation flow mode, with 94% isolated yield for the target N-alkylated product.