Alper Bereketli
Research Subjects
Alper Bereketli has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Burcu Yeni
Defense Systems Technologies Division, Aselsan Inc., Ankara, Turkey
3 shared publicationsIlkay Yazgi
Defense Systems Technologies Division, Aselsan Inc., Ankara, Turkey
3 shared publications- Mehmet Koseoglu
Department of Computer Engineering, Hacettepe University, Ankara, Turkey
3 shared publications Ahmet Gunes
Underwater Acoustic Systems Engineering, Meteksan Savunma Sanayii A.Ş., Ankara, Turkey
2 shared publicationsMehmet B. Guldogan
Department of Electrical and Electronics Engineering, Turgut Ozal University, 06010 Ankara, Turkey
2 shared publicationsSemih Bilgen
Department of Electrical and Electronics Engineering Middle East Technical University, Ankara, Turkey
2 shared publications
Latest Publications
- 12 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Green Communications and Networking
- Vol. 10, 765-779
A Spatial TDMA-Based Medium Access Control Protocol for Underwater Acoustic Backscatter Networks
Underwater acoustic backscatter networks (UABN) constitute a promising communication paradigm, where battery-free nodes transmit data by modulating and reflecting a fraction of an incident carrier signal from an acoustic source, removing the network lifetime constraint due to depletion of batteries. Recently, solutions have been proposed for the deployment, coverage and link modeling problems in UABN. However, efficient data collection from the sensing region to multiple receivers further requires medium access control (MAC) among nodes. In this paper, a centralized MAC protocol, called UABN-MAC, is proposed for low-latency and reliable data collection in multistatic UABN. UABN-MAC incorporates source-controlled TDMA and does not require time synchronization among nodes. In order to resolve contention among nodes, the source collects information about total propagation delays between itself and the receivers over all nodes. The delay information is gathered through source transmissions and receiver acknowledgment messages. The source uses the collected network information to group nodes into backscatter clusters for sensor data collection at the receivers. Performance evaluations show that UABN-MAC achieves feasible and scalable UABN operation in terms of slot duration, frame length, delay reduction, channel utilization, throughput, and packet delivery ratio. The analysis results also reveal that the protocol is robust against synchronization errors among the source and receivers.
- 12 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Green Communications and Networking
- Vol. 10, 765-779
A Spatial TDMA-Based Medium Access Control Protocol for Underwater Acoustic Backscatter Networks
Underwater acoustic backscatter networks (UABN) constitute a promising communication paradigm, where battery-free nodes transmit data by modulating and reflecting a fraction of an incident carrier signal from an acoustic source, removing the network lifetime constraint due to depletion of batteries. Recently, solutions have been proposed for the deployment, coverage and link modeling problems in UABN. However, efficient data collection from the sensing region to multiple receivers further requires medium access control (MAC) among nodes. In this paper, a centralized MAC protocol, called UABN-MAC, is proposed for low-latency and reliable data collection in multistatic UABN. UABN-MAC incorporates source-controlled TDMA and does not require time synchronization among nodes. In order to resolve contention among nodes, the source collects information about total propagation delays between itself and the receivers over all nodes. The delay information is gathered through source transmissions and receiver acknowledgment messages. The source uses the collected network information to group nodes into backscatter clusters for sensor data collection at the receivers. Performance evaluations show that UABN-MAC achieves feasible and scalable UABN operation in terms of slot duration, frame length, delay reduction, channel utilization, throughput, and packet delivery ratio. The analysis results also reveal that the protocol is robust against synchronization errors among the source and receivers.
- Open Access
- 21 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 123560-123578
Three Dimensional Volume Coverage in Multistatic Sonar Sensor Networks
Recent changes in the design of enemy threats such as submarines and the technological achievements in sensor development have paved the way for multistatic sonar applications, which increase security and situational awareness in underwater tactical operations. Previously, coverage in multistatic sonar sensor networks (MSSN) was studied using Cassini ovals and the traditional sonar detection model in two dimensions without any discussion of the practicability and feasibility in terms of conditions related to the underwater acoustic propagation environment. In this study, a practical three-dimensional MSSN channel model is proposed. The proposed model covers a spectral variation of absorption loss, ambient noise, sound speed profile, and shadow zones. The realistic effects of sound propagation and environmental conditions are modeled and evaluated using Lybin, which is a well-known sonar performance prediction tool. Using the practical MSSN channel model, the number of source-receiver pairs required to cover a three-dimensional MSSN volume is calculated. The impacts of frequency, source-to-receiver distance, and source level are investigated. The results are compared to the Cassini oval and traditional sonar detection models via an error expression derived according to our verified practical model. The results reveal that the inclusion of ambient conditions and sound propagation characteristics in the channel model leads to huge error levels of 4700000% in the Cassini oval model and 170000% in the traditional sonar detection model, depending on frequency. Thus, the applicability of these models in realistic MSSN deployment scenarios is limited.
- 21 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 123560-123578
Open AccessThree Dimensional Volume Coverage in Multistatic Sonar Sensor Networks
Recent changes in the design of enemy threats such as submarines and the technological achievements in sensor development have paved the way for multistatic sonar applications, which increase security and situational awareness in underwater tactical operations. Previously, coverage in multistatic sonar sensor networks (MSSN) was studied using Cassini ovals and the traditional sonar detection model in two dimensions without any discussion of the practicability and feasibility in terms of conditions related to the underwater acoustic propagation environment. In this study, a practical three-dimensional MSSN channel model is proposed. The proposed model covers a spectral variation of absorption loss, ambient noise, sound speed profile, and shadow zones. The realistic effects of sound propagation and environmental conditions are modeled and evaluated using Lybin, which is a well-known sonar performance prediction tool. Using the practical MSSN channel model, the number of source-receiver pairs required to cover a three-dimensional MSSN volume is calculated. The impacts of frequency, source-to-receiver distance, and source level are investigated. The results are compared to the Cassini oval and traditional sonar detection models via an error expression derived according to our verified practical model. The results reveal that the inclusion of ambient conditions and sound propagation characteristics in the channel model leads to huge error levels of 4700000% in the Cassini oval model and 170000% in the traditional sonar detection model, depending on frequency. Thus, the applicability of these models in realistic MSSN deployment scenarios is limited.
- 9 March 2022
- Published by Springer Nature in Peer-to-Peer Networking and Applications
- Vol. 15 (3) , 1577-1594
Interference-Free Source Deployment for Coverage in Underwater Acoustic Backscatter Networks
- 9 March 2022
- Published by Springer Nature in Peer-to-Peer Networking and Applications
- Vol. 15 (3) , 1577-1594
Interference-Free Source Deployment for Coverage in Underwater Acoustic Backscatter Networks
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Battery-powered AUV network lifetime under energy constraints
With the recent advances in autonomous underwater vehicle (AUV) technology, it has become feasible to deploy AUV fleets as ad hoc networks for coordinated missions such as remote intelligence, area mapping, and tactical surveillance. In these unattended missions, AUVs are typically sent by a central node, such as a submarine, and they move autonomously. Although there is no need for continuous monitoring of AUV nodes, the central node may occasionally need to broadcast a message to all nodes in the fleet to announce any mission change, such as re-routing or ordering them to return back to the base. However, maximum duration of the mission depends on the lifetime of the AUV network, which is limited by the size and capacity of on-board batteries. This necessitates the detailed analysis of energy consumption characteristics and lifetime constraints in order to avoid operational failure. Here we study the connectivity properties of an energy-constrained ad-hoc AUV network through broadcast simulations. We obtained results with respect to the number of packets transmitted, the total number of nodes, and their mobility characteristics. Our results provide key parameters that must be taken into account in the design and deployment of AUV networks.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Battery-powered AUV network lifetime under energy constraints
With the recent advances in autonomous underwater vehicle (AUV) technology, it has become feasible to deploy AUV fleets as ad hoc networks for coordinated missions such as remote intelligence, area mapping, and tactical surveillance. In these unattended missions, AUVs are typically sent by a central node, such as a submarine, and they move autonomously. Although there is no need for continuous monitoring of AUV nodes, the central node may occasionally need to broadcast a message to all nodes in the fleet to announce any mission change, such as re-routing or ordering them to return back to the base. However, maximum duration of the mission depends on the lifetime of the AUV network, which is limited by the size and capacity of on-board batteries. This necessitates the detailed analysis of energy consumption characteristics and lifetime constraints in order to avoid operational failure. Here we study the connectivity properties of an energy-constrained ad-hoc AUV network through broadcast simulations. We obtained results with respect to the number of packets transmitted, the total number of nodes, and their mobility characteristics. Our results provide key parameters that must be taken into account in the design and deployment of AUV networks.
- 3 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Connectivity analysis of an AUV network with OFDM based communications
Autonomous underwater vehicle (AUV) networks play a crucial role in tactical, commercial, and scientific applications, where reliable and robust communication protocols are needed due to the challenging characteristics of the channel. With this motivation, connectivity of AUV networks in different regions with varying transducer characteristics are analyzed through simulations based on real-life orthogonal frequency division multiplexing (OFDM) based communication experiments over noisy and Doppler-distorted channels. Doppler compensation is performed according to the autocorrelation using the cyclic prefix. Using binary and quadrature phase shift keying (BPSK and QPSK) modulation schemes in conjunction with low density parity check (LDPC) coding, error rate levels are investigated through shallow water pond and at-sea experiments. It is shown that, the utilized transmission scheme is capable of correcting all bit errors among nearly one million bits transmitted up to a distance of 1 km, yielding a payload rate of 15.6 kbps with 4096 subcarriers and QPSK modulation. The simulations provide key parameters that must be taken into account in the design of scalable and connected AUV networks.
- 3 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Connectivity analysis of an AUV network with OFDM based communications
Autonomous underwater vehicle (AUV) networks play a crucial role in tactical, commercial, and scientific applications, where reliable and robust communication protocols are needed due to the challenging characteristics of the channel. With this motivation, connectivity of AUV networks in different regions with varying transducer characteristics are analyzed through simulations based on real-life orthogonal frequency division multiplexing (OFDM) based communication experiments over noisy and Doppler-distorted channels. Doppler compensation is performed according to the autocorrelation using the cyclic prefix. Using binary and quadrature phase shift keying (BPSK and QPSK) modulation schemes in conjunction with low density parity check (LDPC) coding, error rate levels are investigated through shallow water pond and at-sea experiments. It is shown that, the utilized transmission scheme is capable of correcting all bit errors among nearly one million bits transmitted up to a distance of 1 km, yielding a payload rate of 15.6 kbps with 4096 subcarriers and QPSK modulation. The simulations provide key parameters that must be taken into account in the design of scalable and connected AUV networks.
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Probabilistic broadcast for dense AUV networks
As the technology behind autonomous underwater vehicles (AUV) becomes more feasible, it is possible to use fleets of AUVs for coordinated missions such as area mapping, surveillance, etc. The AUVs are typically sent by a central node such as a submarine and move autonomously. Although there is no need for continuous monitoring of AUV nodes, the central node may occasionally need to send a broadcast message to all nodes in the fleet to announce a change in mission; e.g. ordering nodes to return back to the base. To address this need, reliable and low-latency broadcast algorithms for underwater networks are needed. Here we investigate the performance of probabilistic broadcast for AUV networks where the AUVs are not aware of locations of their neighbors. Our results indicate that probabilistic broadcast significantly improves average and maximum delay along with energy consumption in comparison to simple flooding especially for dense networks.
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Probabilistic broadcast for dense AUV networks
As the technology behind autonomous underwater vehicles (AUV) becomes more feasible, it is possible to use fleets of AUVs for coordinated missions such as area mapping, surveillance, etc. The AUVs are typically sent by a central node such as a submarine and move autonomously. Although there is no need for continuous monitoring of AUV nodes, the central node may occasionally need to send a broadcast message to all nodes in the fleet to announce a change in mission; e.g. ordering nodes to return back to the base. To address this need, reliable and low-latency broadcast algorithms for underwater networks are needed. Here we investigate the performance of probabilistic broadcast for AUV networks where the AUVs are not aware of locations of their neighbors. Our results indicate that probabilistic broadcast significantly improves average and maximum delay along with energy consumption in comparison to simple flooding especially for dense networks.
- Open Access
- 19 May 2015
- Published by Hindawi Limited in Journal of Sensors
- Vol. 2015, 1-10
Experimental Results for Direction of Arrival Estimation with a Single Acoustic Vector Sensor in Shallow Water
We study the performances of several computationally efficient and simple techniques for estimating direction of arrival (DOA) of an underwater acoustic source using a single acoustic vector sensor (AVS) in shallow water. Underwater AVS is a compact device, which consists of one hydrophone and three accelerometers in a packaged form, measuring scalar pressure and three-dimensional acceleration simultaneously at a single position. A very controlled experimental setup is prepared to test how well-known techniques, namely, arctan-based, intensity-based, time domain beamforming, and frequency domain beamforming methods, perform in estimating DOA of a source in different circumstances. Experimental results reveal that for almost all cases beamforming techniques perform best. Moreover, arctan-based method, which is the simplest of all, provides satisfactory results for practical purposes.
- 19 May 2015
- Published by Hindawi Limited in Journal of Sensors
- Vol. 2015, 1-10
Open AccessExperimental Results for Direction of Arrival Estimation with a Single Acoustic Vector Sensor in Shallow Water
We study the performances of several computationally efficient and simple techniques for estimating direction of arrival (DOA) of an underwater acoustic source using a single acoustic vector sensor (AVS) in shallow water. Underwater AVS is a compact device, which consists of one hydrophone and three accelerometers in a packaged form, measuring scalar pressure and three-dimensional acceleration simultaneously at a single position. A very controlled experimental setup is prepared to test how well-known techniques, namely, arctan-based, intensity-based, time domain beamforming, and frequency domain beamforming methods, perform in estimating DOA of a source in different circumstances. Experimental results reveal that for almost all cases beamforming techniques perform best. Moreover, arctan-based method, which is the simplest of all, provides satisfactory results for practical purposes.
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A comparative study on the performances of the DF techniques using a single acoustic vector sensor
Underwater acoustic vector sensors (AVS) are devices which can measure scalar pressure and three dimensional acceleration or particle velocity with only one sensor. Direction of an acoustic target can be estimated by these four measured scalar values. Techniques based on either closed-form expressions or beamforming can be carried out for direction finding by using the axial projections of the gradient vector of the pressure from the target. In this work, the performances of direction of arrival (DOA) estimation techniques for a single underwater AVS are analyzed in detail under the effects of various error sources such as imperfect projections and ambient noise.
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A comparative study on the performances of the DF techniques using a single acoustic vector sensor
Underwater acoustic vector sensors (AVS) are devices which can measure scalar pressure and three dimensional acceleration or particle velocity with only one sensor. Direction of an acoustic target can be estimated by these four measured scalar values. Techniques based on either closed-form expressions or beamforming can be carried out for direction finding by using the axial projections of the gradient vector of the pressure from the target. In this work, the performances of direction of arrival (DOA) estimation techniques for a single underwater AVS are analyzed in detail under the effects of various error sources such as imperfect projections and ambient noise.
- 1 April 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 289-292
Analysis of direction finding techniques using a single underwater acoustic vector sensor
Underwater acoustic vector sensors (AVS) are devices which can measure scalar pressure and three dimensional acceleration or particle velocity with only one sensor. Bearing estimation for the target can be accomplished by these four measured scalar values. Algorithms based on closed-form expressions or beamforming can be carried out for direction finding by using the axial projections of the gradient vector of the pressure from the target. In this work, the performances of direction of arrival estimation algorithms for underwater acoustic vector sensors are analyzed in detail under the effects of various error sources such as imperfect projections and ambient noise.
- 1 April 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 289-292
Analysis of direction finding techniques using a single underwater acoustic vector sensor
Underwater acoustic vector sensors (AVS) are devices which can measure scalar pressure and three dimensional acceleration or particle velocity with only one sensor. Bearing estimation for the target can be accomplished by these four measured scalar values. Algorithms based on closed-form expressions or beamforming can be carried out for direction finding by using the axial projections of the gradient vector of the pressure from the target. In this work, the performances of direction of arrival estimation algorithms for underwater acoustic vector sensors are analyzed in detail under the effects of various error sources such as imperfect projections and ambient noise.
- 1 June 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 26-33
Cross Layer Power Adaptive CSMA/CA for Sink Powered Underwater Acoustic Sensor Networks
The term Sink Powered Underwater Acoustic Sensor Networks (SPUASN) refers to a special configuration within the recent Remotely Powered Underwater Acoustic Sensor Networks (RPUASN) paradigm, where the data sink supplies energy to battery-free sensors that constitute the network. In this paper, we introduce the Cross Layer Power Adaptive CSMA/CA (X-PACCA) protocol for SPUASN. Fully free from energy constraints of traditional protocols, X-PACCA integrates MAC, network, and transport layer functionalities. Packet relaying/routing is based on CSMA/CA backoff window size adjustment according to harvested power levels at nodes. End-to-end reliability is enhanced via acknowledgments sent by the sink. Congestion is avoided via prevention of redundant packet forwarding. Neither global network information nor synchronization is required at nodes. It is shown that, with appropriate selection of protocol parameters, X-PACCA achieves low end-to-end latency and high packet delivery performance.
- 1 June 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 26-33
Cross Layer Power Adaptive CSMA/CA for Sink Powered Underwater Acoustic Sensor Networks
The term Sink Powered Underwater Acoustic Sensor Networks (SPUASN) refers to a special configuration within the recent Remotely Powered Underwater Acoustic Sensor Networks (RPUASN) paradigm, where the data sink supplies energy to battery-free sensors that constitute the network. In this paper, we introduce the Cross Layer Power Adaptive CSMA/CA (X-PACCA) protocol for SPUASN. Fully free from energy constraints of traditional protocols, X-PACCA integrates MAC, network, and transport layer functionalities. Packet relaying/routing is based on CSMA/CA backoff window size adjustment according to harvested power levels at nodes. End-to-end reliability is enhanced via acknowledgments sent by the sink. Congestion is avoided via prevention of redundant packet forwarding. Neither global network information nor synchronization is required at nodes. It is shown that, with appropriate selection of protocol parameters, X-PACCA achieves low end-to-end latency and high packet delivery performance.