Ghislain Despesse
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ghislain Despesse has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Sebastien Boisseau
Univ. Grenoble Alpes
5 shared publications - Francois Costa
SATIE Laboratory Universit Paris Est Crteil, ENS Paris-Saclay, CNRS, Universit Paris-Saclay, Gif sur Yvette, France
3 shared publications - Mustapha Touhami
CEA-LETI, Grenoble, France
3 shared publications - Rémy Thomas
CEA, LITEN, Université Grenoble Alpes, F-38000 Grenoble, France
3 shared publications - Nicolas Garraud
CEA-Leti (Laboratoire d’Électronique des Technologies de l’Information), Université Grenoble Alpes, 38000 Grenoble, France
2 shared publications - Olivier Freychet
Univ. Grenoble Alpes, CEA, LETI, F-38000 Grenoble, France
2 shared publications
Latest Publications
- 1 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
EMC Conducted Emissions Reduction with Two 50W Symmetric Class DE Inverters Operating in Antiphase at 13.56 MHz
Electromagnetic compatibility (EMC) for very high frequency (VHF) converter topologies is not often discussed in the literature. However, as those converters have industrial applications, like plasma generation or wireless power transfer (WPT), they must comply with EMC regulations. Many solutions exist to avoid or attenuate electromagnetic emissions. In this article, a solution to reduce VHF inverters emissions, that could apply to other kind of converters, is investigated. By using two inverters operating in antiphase, perturbations generated by each inverter in antiphase should cancel-out to an extent. A $2 \times 50\ \mathrm{W}$ symmetric class DE push-pull inverter operating at $\mathbf{1 3. 5 6 M H z}$ is designed and tested to experimentally verify the reduction in conducted emission. A reduction of emissions is observed on the fundamental and odd harmonics, as well as on the peak caused by the switching operation, compared to when both inverters operate in phase.- 1 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
EMC Conducted Emissions Reduction with Two 50W Symmetric Class DE Inverters Operating in Antiphase at 13.56 MHz
Electromagnetic compatibility (EMC) for very high frequency (VHF) converter topologies is not often discussed in the literature. However, as those converters have industrial applications, like plasma generation or wireless power transfer (WPT), they must comply with EMC regulations. Many solutions exist to avoid or attenuate electromagnetic emissions. In this article, a solution to reduce VHF inverters emissions, that could apply to other kind of converters, is investigated. By using two inverters operating in antiphase, perturbations generated by each inverter in antiphase should cancel-out to an extent. A $2 \times 50\ \mathrm{W}$ symmetric class DE push-pull inverter operating at $\mathbf{1 3. 5 6 M H z}$ is designed and tested to experimentally verify the reduction in conducted emission. A reduction of emissions is observed on the fundamental and odd harmonics, as well as on the peak caused by the switching operation, compared to when both inverters operate in phase.- 19 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (5) , 3123-3129
Toward the Understanding on Threshold Voltage Drift Mechanisms in GaN MOSc-HEMTs Through the Influence of Device Architecture
In this article, the impact of device architecture on threshold voltage VTH instabilities during OFF state operation under a high drain voltage stress on GaN-on-Si MOSc HEMTs is thoroughly investigated. Measurement-stress–measurement high-voltage bias temperature instability (HVBTI) technique using ultrafast VGS ramp was used in this study. This measurement technique was carried out on various gate length ( ${L}_{G}$ ), ohmic length (LOHM), and field plate (FP) length. HVBTI transients performed at different ${L}_{G}$ highlight that increasing the gate length induces a better electrostatic control under the gate via a gate shielding. TCAD simulations support the claim that the relaxation peak is linked to the charge redistribution of ionized ${C}_{N}$ (-) traps under the gate. This charge redistribution during the relaxation phase is enhanced using a larger ohmic contact area. The electric field at gate and source FP corners has a strong impact on ionized ${C}_{N}$ acceptor traps located in the GaN:C layer close to the gate and consequently on positive VTH degradation observed for short stress duration. Substrate biasing and TCAD simulations suggest that the ${C}_{N}$ traps’ deionization and trapping in the volume of the gate oxide is related to the presence of free holes in the GaN:C layer.
- 19 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (5) , 3123-3129
Toward the Understanding on Threshold Voltage Drift Mechanisms in GaN MOSc-HEMTs Through the Influence of Device Architecture
In this article, the impact of device architecture on threshold voltage VTH instabilities during OFF state operation under a high drain voltage stress on GaN-on-Si MOSc HEMTs is thoroughly investigated. Measurement-stress–measurement high-voltage bias temperature instability (HVBTI) technique using ultrafast VGS ramp was used in this study. This measurement technique was carried out on various gate length ( ${L}_{G}$ ), ohmic length (LOHM), and field plate (FP) length. HVBTI transients performed at different ${L}_{G}$ highlight that increasing the gate length induces a better electrostatic control under the gate via a gate shielding. TCAD simulations support the claim that the relaxation peak is linked to the charge redistribution of ionized ${C}_{N}$ (-) traps under the gate. This charge redistribution during the relaxation phase is enhanced using a larger ohmic contact area. The electric field at gate and source FP corners has a strong impact on ionized ${C}_{N}$ acceptor traps located in the GaN:C layer close to the gate and consequently on positive VTH degradation observed for short stress duration. Substrate biasing and TCAD simulations suggest that the ${C}_{N}$ traps’ deionization and trapping in the volume of the gate oxide is related to the presence of free holes in the GaN:C layer.
- 16 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (8) , 10012-10025
A New Isolated Topology of DC–DC Converter Based on Piezoelectric Resonators
This article presents a new isolated topology of dc–dc converter based on piezoelectric resonators. Contrary to most existing topologies, the proposed one uses the natural isolation of piezoelectric resonators to isolate the converter's output from the input and vice-versa. Considering the resonators’ constraints, our study focuses on the most efficient isolated conversion cycle with zero-voltage switching (ZVS) operations. The case studied is a highly efficient step-down isolated dc–dc converter with a gain ranging from 0 to 1 and an input voltage up to 360 V. The converter uses two piezoelectric resonators working in series. The conversion principle is validated thanks to a prototype operating at a frequency around 95 kHz. Experimental measurements are made on a wide range of input voltage from 12 to 360 V with a conversion ratio of 0.0165 to 0.95. The output power reaches either 179.1 W with an 89% efficiency at 360 V input voltage and 346 V output voltage, or 4.5 W with a 97.2% peak efficiency for a 48 to 45.8 V conversion, using a 25 mm piezoelectric disc with a thickness of 2 and 1 mm, respectively. An efficiency higher than 80% is measured over a wide range of operating points.
- 16 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (8) , 10012-10025
A New Isolated Topology of DC–DC Converter Based on Piezoelectric Resonators
This article presents a new isolated topology of dc–dc converter based on piezoelectric resonators. Contrary to most existing topologies, the proposed one uses the natural isolation of piezoelectric resonators to isolate the converter's output from the input and vice-versa. Considering the resonators’ constraints, our study focuses on the most efficient isolated conversion cycle with zero-voltage switching (ZVS) operations. The case studied is a highly efficient step-down isolated dc–dc converter with a gain ranging from 0 to 1 and an input voltage up to 360 V. The converter uses two piezoelectric resonators working in series. The conversion principle is validated thanks to a prototype operating at a frequency around 95 kHz. Experimental measurements are made on a wide range of input voltage from 12 to 360 V with a conversion ratio of 0.0165 to 0.95. The output power reaches either 179.1 W with an 89% efficiency at 360 V input voltage and 346 V output voltage, or 4.5 W with a 97.2% peak efficiency for a 48 to 45.8 V conversion, using a 25 mm piezoelectric disc with a thickness of 2 and 1 mm, respectively. An efficiency higher than 80% is measured over a wide range of operating points.
- Open Access
- 19 April 2023
- Published by MDPI AG in Electronics
- Vol. 12 (8) , 1929
Comparison between a Cascaded H-Bridge and a Conventional H-Bridge for a 5-kW Grid-Tied Solar Inverter
This paper compares the cost and efficiency of two inverter topologies for a 5-kW grid-connected solar inverter application: the Conventional H-Bridge Inverter (CHB) and the Cascaded H-Bridge Multilevel Inverter (CHBMLI). Emphasis is put on power switches and passive elements with a detailed study of the losses. Both designs respect the same constraints (cost, efficiency, and junction temperature of the transistors) to ensure a fair comparison between both topologies. The work highlights the important parameters when choosing the components (MOSFETs, capacitors, and magnetic cores for the inductors). The DC-link voltage ripple and the output AC current ripple are the key parameters for the design of the passive elements (capacitors and inductors). On top of that, the transistors MOSFETs are chosen, in both topologies, to limit the conduction losses (by selecting the ) and the switching losses (by selecting the and ). Real components are picked in order to make the comparison as complete as possible. Numerical simulations are performed using the MATLAB platform. All equations and parameters are provided. A CHBMLI prototype was built with eight independent H-Bridges to validate the proposed design with thermal and efficiency measurements.- 19 April 2023
- Published by MDPI AG in Electronics
- Vol. 12 (8) , 1929
Open AccessComparison between a Cascaded H-Bridge and a Conventional H-Bridge for a 5-kW Grid-Tied Solar Inverter
This paper compares the cost and efficiency of two inverter topologies for a 5-kW grid-connected solar inverter application: the Conventional H-Bridge Inverter (CHB) and the Cascaded H-Bridge Multilevel Inverter (CHBMLI). Emphasis is put on power switches and passive elements with a detailed study of the losses. Both designs respect the same constraints (cost, efficiency, and junction temperature of the transistors) to ensure a fair comparison between both topologies. The work highlights the important parameters when choosing the components (MOSFETs, capacitors, and magnetic cores for the inductors). The DC-link voltage ripple and the output AC current ripple are the key parameters for the design of the passive elements (capacitors and inductors). On top of that, the transistors MOSFETs are chosen, in both topologies, to limit the conduction losses (by selecting the ) and the switching losses (by selecting the and ). Real components are picked in order to make the comparison as complete as possible. Numerical simulations are performed using the MATLAB platform. All equations and parameters are provided. A CHBMLI prototype was built with eight independent H-Bridges to validate the proposed design with thermal and efficiency measurements. - Open Access
- 1 December 2022
- Published by MDPI AG in Electronics
- Vol. 11 (23) , 3983
Comparison between Piezoelectric Filter and Passive LC Filter in a Class L−Piezo Inverter
This paper presents a comparison between piezoelectric filtering and passive LC filtering integrated into an HF class L−Piezo inverter. This L−Piezo inverter is a variant of class φ2 where the filtering of the second harmonic is carried out by a piezoelectric resonator. Piezoelectric filters are well known in the signal domain (RF filtering), but their use in the field of power electronics, as a temporary energy storage element, is rather recent. In power electronics, piezoelectricity has mainly been used as a transformer, in particular, to greatly increase voltages (backlight applications). A class L−Piezo inverter with Lithium Niobate (LNO) piezoelectric resonator is designed for a switching frequency of 10.4 MHz, an input voltage of 30 V, and an output power of 15 W. To compare these two filtering methods, two prototypes are built, one with piezoelectric filtering and one with passive LC filtering. Measurements show a reduction of 60% of the losses in the filter, while the volume of the filter is reduced by a factor of 50.
- 1 December 2022
- Published by MDPI AG in Electronics
- Vol. 11 (23) , 3983
Open AccessComparison between Piezoelectric Filter and Passive LC Filter in a Class L−Piezo Inverter
This paper presents a comparison between piezoelectric filtering and passive LC filtering integrated into an HF class L−Piezo inverter. This L−Piezo inverter is a variant of class φ2 where the filtering of the second harmonic is carried out by a piezoelectric resonator. Piezoelectric filters are well known in the signal domain (RF filtering), but their use in the field of power electronics, as a temporary energy storage element, is rather recent. In power electronics, piezoelectricity has mainly been used as a transformer, in particular, to greatly increase voltages (backlight applications). A class L−Piezo inverter with Lithium Niobate (LNO) piezoelectric resonator is designed for a switching frequency of 10.4 MHz, an input voltage of 30 V, and an output power of 15 W. To compare these two filtering methods, two prototypes are built, one with piezoelectric filtering and one with passive LC filtering. Measurements show a reduction of 60% of the losses in the filter, while the volume of the filter is reduced by a factor of 50.
- 13 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (6) , 6986-7000
A New Topology of DC–DC Converter Based on Piezoelectric Resonator
The emergence of new piezoelectric materials makes it possible to offer high performances in terms of power density and integration. These new materials can be used in dc–dc power converters as a solution to replace the magnetic components and to meet the growing demand for miniaturization, high power density, and high-efficiency applications. This article deals with a new topology of a dc–dc converter based on a piezoelectric resonator. The conversion mechanism based on energy and charge balance is explained in detail through an analytical model and validated by experimental results. A prototype has been designed for an input–output voltage up to 250–125 V and a power range up to 175 W. It provides an efficiency higher than 93% for wide operating points in radial mode vibration. As an example, we have obtained an efficiency of 93.8% for 250–117 V input–output voltage at 50 W output power. In addition, the thickness mode operation is experimentally validated at 1 MHz and exhibited a peak output power of 175 W with an efficiency of 80% for 200–60 V input–output voltage. The experimental results show the promising performances of the proposed dc–dc power converter based on a piezoelectric resonator for high-to-low voltage, high efficiency, and low-to-medium power applications.
- 13 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (6) , 6986-7000
A New Topology of DC–DC Converter Based on Piezoelectric Resonator
The emergence of new piezoelectric materials makes it possible to offer high performances in terms of power density and integration. These new materials can be used in dc–dc power converters as a solution to replace the magnetic components and to meet the growing demand for miniaturization, high power density, and high-efficiency applications. This article deals with a new topology of a dc–dc converter based on a piezoelectric resonator. The conversion mechanism based on energy and charge balance is explained in detail through an analytical model and validated by experimental results. A prototype has been designed for an input–output voltage up to 250–125 V and a power range up to 175 W. It provides an efficiency higher than 93% for wide operating points in radial mode vibration. As an example, we have obtained an efficiency of 93.8% for 250–117 V input–output voltage at 50 W output power. In addition, the thickness mode operation is experimentally validated at 1 MHz and exhibited a peak output power of 175 W with an efficiency of 80% for 200–60 V input–output voltage. The experimental results show the promising performances of the proposed dc–dc power converter based on a piezoelectric resonator for high-to-low voltage, high efficiency, and low-to-medium power applications.
- Open Access
- 6 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 48-51
Piezoelectric stacks to increase the transmitted power of acoustic power transfer through metal walls
Acoustic power transfer is a wireless power transfer technology that enables to supply sensors placed behind metal walls by using acoustic waves generated by piezoelectric transducers positioned on both sides of the wall. The state of the art reports that high levels of powers, up to hundreds of watts, can be transmitted but at the cost of high input voltage levels, making the control electronics complicated, low-efficient and even hazardous. In this paper, we study and validate experimentally the use a piezoelectric stack to generate the acoustic waves to transmit high power levels with low actuation voltages. By using a stack of four piezoelectric disks, the transmitted power is multiplied by 5 compared to a single disk for the same excitation voltage, and the power density is multiplied by 2, reaching 8.2 mW/V2/cm3.
- 6 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 48-51
Open AccessPiezoelectric stacks to increase the transmitted power of acoustic power transfer through metal walls
Acoustic power transfer is a wireless power transfer technology that enables to supply sensors placed behind metal walls by using acoustic waves generated by piezoelectric transducers positioned on both sides of the wall. The state of the art reports that high levels of powers, up to hundreds of watts, can be transmitted but at the cost of high input voltage levels, making the control electronics complicated, low-efficient and even hazardous. In this paper, we study and validate experimentally the use a piezoelectric stack to generate the acoustic waves to transmit high power levels with low actuation voltages. By using a stack of four piezoelectric disks, the transmitted power is multiplied by 5 compared to a single disk for the same excitation voltage, and the power density is multiplied by 2, reaching 8.2 mW/V2/cm3.
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Piezoelectric Materials for the DC-DC Converters Based on Piezoelectric Resonators
This paper presents a generic representation of the six switching sequences of the dc-dc converters based on piezoelectric resonators. In addition, the estimation of current density and voltage limitations of lead zirconate titanate and lithium niobate resonators are given. A comparison between these piezoelectric materials is carried out. Then, we propose a lithium niobate-based piezoelectric resonator design that reduces spurious modes, while providing a quality factor of 3700 and an electromechanical coupling factor k t 2 of 25.5 %. Experimental results demonstrate the operating principle for input-output voltage of 60-20 V around 6 MHz for a wide power range 2-32 W. A peak efficiency of 93.6 % is obtained at 16 W. A power density of 128 W/cm 3 for the designed resonator is reached for input-output voltage of 60-20 V.
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Piezoelectric Materials for the DC-DC Converters Based on Piezoelectric Resonators
This paper presents a generic representation of the six switching sequences of the dc-dc converters based on piezoelectric resonators. In addition, the estimation of current density and voltage limitations of lead zirconate titanate and lithium niobate resonators are given. A comparison between these piezoelectric materials is carried out. Then, we propose a lithium niobate-based piezoelectric resonator design that reduces spurious modes, while providing a quality factor of 3700 and an electromechanical coupling factor k t 2 of 25.5 %. Experimental results demonstrate the operating principle for input-output voltage of 60-20 V around 6 MHz for a wide power range 2-32 W. A peak efficiency of 93.6 % is obtained at 16 W. A power density of 128 W/cm 3 for the designed resonator is reached for input-output voltage of 60-20 V.
- 24 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (3) , 2508-2512
Operating Frequency Prediction of Piezoelectric DC–DC Converters
Piezoelectric dc–dc converters operate between the series and parallel frequencies of the piezoelectric resonator to achieve soft switching and energy-balance conditions. This letter presents an experimentally validated model to accurately predict the operating frequency, the switching angles, and the piezoelectric current for any six-phase piezoelectric dc–dc converter. This model reduces the transient simulation's calculation time to reach the steady state. It can be used to initially setup the switching angles in the experiment or to predict the high-frequency spectrum generated by the converter cycle.
- 24 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (3) , 2508-2512
Operating Frequency Prediction of Piezoelectric DC–DC Converters
Piezoelectric dc–dc converters operate between the series and parallel frequencies of the piezoelectric resonator to achieve soft switching and energy-balance conditions. This letter presents an experimentally validated model to accurately predict the operating frequency, the switching angles, and the piezoelectric current for any six-phase piezoelectric dc–dc converter. This model reduces the transient simulation's calculation time to reach the steady state. It can be used to initially setup the switching angles in the experiment or to predict the high-frequency spectrum generated by the converter cycle.
- Open Access
- 11 January 2021
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 12 (1) , 10
Performance Analysis of a Novel High Frequency Self-Reconfigurable Battery
Self-reconfigurable battery architectures have gained a lot of interest recently in the literature, with more and more advanced functionalities. This paper describes the performance analysis of our proposed High Frequency Self-Reconfigurable Battery (HF SRB). To evaluate specific features with long-term dependencies of our system, a full functional behavioral simulator was developed. A comparison with a real 128-level HF SRB validated the simulator operation. The balancing performances obtained on vehicle test cycles showed the cell capacity discrepancy that the HF SRB is capable of handling in a single complete charge or discharge cycle. The magnitude of this gap demonstrated the extent to which the HF SRB is capable of operating with second life cells or even different chemistry mixes.
- 11 January 2021
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 12 (1) , 10
Open AccessPerformance Analysis of a Novel High Frequency Self-Reconfigurable Battery
Self-reconfigurable battery architectures have gained a lot of interest recently in the literature, with more and more advanced functionalities. This paper describes the performance analysis of our proposed High Frequency Self-Reconfigurable Battery (HF SRB). To evaluate specific features with long-term dependencies of our system, a full functional behavioral simulator was developed. A comparison with a real 128-level HF SRB validated the simulator operation. The balancing performances obtained on vehicle test cycles showed the cell capacity discrepancy that the HF SRB is capable of handling in a single complete charge or discharge cycle. The magnitude of this gap demonstrated the extent to which the HF SRB is capable of operating with second life cells or even different chemistry mixes.