George Vicatos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
George Vicatos has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
A. Bennett
1 shared publication- Deon de Beer
Centre for Rapid Prototyping and Manufacturing, Central University of Technology, Bloemfontein, South Africa
1 shared publication E. Krafft
1 shared publicationGerrie Booysen
Central University of Technology, Bloemfontein, Free State, South Africa
1 shared publicationKeith Hosking
Grootte Schuur and Vincent Palotti Hospitals, Cape Town, South Africa
1 shared publicationLudrick Barnard
Central University of Technology, Bloemfontein, Free State, South Africa
1 shared publication
Latest Publications
- Open Access
- 1 August 2010
- Published by Academy of Science of South Africa in Journal of Energy in Southern Africa
- Vol. 21 (3) , 16-22
Comparison between two different solution-pumping methods in absorption refrigeration machines
This paper presents a pumping method in absorp-tion refrigeration where a vapour-driven pump is to replace the electricity-driven pump. The vapour pump is driven by a fraction of the generator’s hot, high-pressure, vapour mixture. The refrigerator is thus exclusively heat-powered and rendered inde-pendent of the availability of electricity as the main energy source. The design and operation of the vapour pump is presented. The results obtained by a computer simulation program show a decrease in performance (COP), which is confirmed by the data obtained from a 1 kW cooling capacity refrigerator. Peak performances occur at higher generator tem-peratures when compared to a cycle using an elec-tricity-driven pump
- 1 August 2010
- Published by Academy of Science of South Africa in Journal of Energy in Southern Africa
- Vol. 21 (3) , 16-22
Open AccessComparison between two different solution-pumping methods in absorption refrigeration machines
This paper presents a pumping method in absorp-tion refrigeration where a vapour-driven pump is to replace the electricity-driven pump. The vapour pump is driven by a fraction of the generator’s hot, high-pressure, vapour mixture. The refrigerator is thus exclusively heat-powered and rendered inde-pendent of the availability of electricity as the main energy source. The design and operation of the vapour pump is presented. The results obtained by a computer simulation program show a decrease in performance (COP), which is confirmed by the data obtained from a 1 kW cooling capacity refrigerator. Peak performances occur at higher generator tem-peratures when compared to a cycle using an elec-tricity-driven pump
- Open Access
- 1 August 2007
- Published by Academy of Science of South Africa in Journal of Energy in Southern Africa
- Vol. 18 (4) , 49-57
Multiple lift tube pumps boost refrigeration capacity in absorption plants
The technology of the diffusion absorption refriger-ator is receiving renewed attention due to its ability to use exclusively, low-grade heat to produce cool-ing or heating. Its capacity, however, has been large-ly restricted to small domestic-type units because of the flow rate limitations imposed by its single lift-tube pump. To increase its refrigeration capacity, a multiple lift-tube bubble pump can be used, in order to increase the volume flow rates of the fluids, which are directly related to the amount of refriger-ant produced. Testing on a diffusion absorption plant using a multiple lift tube bubble pump, and the effects of additional tubes on the system’s per-formance have been recorded. Although a full range of heat inputs could not be implemented, because of the limitations of the components of the unit itself, it was observed that the refrigeration cooling capacity was increased without a significant drop in Coefficient of Performance (COP). It was concluded that the multiple lift tube bubble pump has no limitation to the fluid flow rate and depends solely on the amount of heat input. This gives the freedom to design the lift tube pump according to the refrigeration demand of the unit, and not the other way round which is the current approach by the manufacturers world wide.
- 1 August 2007
- Published by Academy of Science of South Africa in Journal of Energy in Southern Africa
- Vol. 18 (4) , 49-57
Open AccessMultiple lift tube pumps boost refrigeration capacity in absorption plants
The technology of the diffusion absorption refriger-ator is receiving renewed attention due to its ability to use exclusively, low-grade heat to produce cool-ing or heating. Its capacity, however, has been large-ly restricted to small domestic-type units because of the flow rate limitations imposed by its single lift-tube pump. To increase its refrigeration capacity, a multiple lift-tube bubble pump can be used, in order to increase the volume flow rates of the fluids, which are directly related to the amount of refriger-ant produced. Testing on a diffusion absorption plant using a multiple lift tube bubble pump, and the effects of additional tubes on the system’s per-formance have been recorded. Although a full range of heat inputs could not be implemented, because of the limitations of the components of the unit itself, it was observed that the refrigeration cooling capacity was increased without a significant drop in Coefficient of Performance (COP). It was concluded that the multiple lift tube bubble pump has no limitation to the fluid flow rate and depends solely on the amount of heat input. This gives the freedom to design the lift tube pump according to the refrigeration demand of the unit, and not the other way round which is the current approach by the manufacturers world wide.
- 3 April 2007
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 13 (2) , 107-114
Using RP to promote collaborative design of customised medical implants
Purpose: The last decade has seen major advances in rapid prototyping (RP), with it becoming a multi‐disciplinary technology, crossing various research fields, and connecting continents. Process and material advancements open up new applications and manufacturing (through RP) is serving non‐traditional industries. RP technology is used to support rapid product development (RPD). The purpose of this paper is to describe how the Integrated Product Development research group of the Central University of Technology, Free State, South Africa is applying various CAD/CAM/RP technologies to support a medical team from the Grootte Schuur and Vincent Palotti hospitals in Cape Town, to save limbs – as a last resort at a stage where conventional medical techniques or practices may not apply any longer.Design/methodology/approach: The paper uses action research to justify the proposal of a new method to use CAD/CAM/RP related technologies to substitute lost/damaged bone regions through the use of CT to CAD to.STL manipulation.Findings: A case study where RP related technologies were used to support medical product development for a patient with severe injuries from a road accident is discussed.Originality/value: The paper considers current available technologies, and discusses new advancements in direct metal freeform fabrication, and its potential to revolutionise the medical industry.
- 3 April 2007
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 13 (2) , 107-114
Using RP to promote collaborative design of customised medical implants
Purpose: The last decade has seen major advances in rapid prototyping (RP), with it becoming a multi‐disciplinary technology, crossing various research fields, and connecting continents. Process and material advancements open up new applications and manufacturing (through RP) is serving non‐traditional industries. RP technology is used to support rapid product development (RPD). The purpose of this paper is to describe how the Integrated Product Development research group of the Central University of Technology, Free State, South Africa is applying various CAD/CAM/RP technologies to support a medical team from the Grootte Schuur and Vincent Palotti hospitals in Cape Town, to save limbs – as a last resort at a stage where conventional medical techniques or practices may not apply any longer.Design/methodology/approach: The paper uses action research to justify the proposal of a new method to use CAD/CAM/RP related technologies to substitute lost/damaged bone regions through the use of CT to CAD to.STL manipulation.Findings: A case study where RP related technologies were used to support medical product development for a patient with severe injuries from a road accident is discussed.Originality/value: The paper considers current available technologies, and discusses new advancements in direct metal freeform fabrication, and its potential to revolutionise the medical industry.