Jean-Yves Trépanier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jean-Yves Trépanier has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Christophe Tribes
Group for Research in Decision Analysis image/svg+xml
5 shared publications M. Reggio
Ecole Polytechnique de Montreal, Montreal, Quebec H3C 3A7, Canada
3 shared publicationsR. Camarero
Ecole Polytechnique de Montreal, Montreal, Quebec H3C 3A7, Canada
3 shared publicationsRicardo Camarero
3 shared publicationsEddy Petro
Ecole Polytechnique de Montréal
2 shared publications- Sébastien Leclaire
Research Center in Industrial Flow Processes (URPEI), Polytechnique Montréal
2 shared publications
Latest Publications
- Open Access
Lattice Boltzmann Model for Rarefied Gaseous Mixture Flows in Three-Dimensional Porous Media Including Knudsen Diffusion
Numerical modeling of gas flows in rarefied regimes is crucial in understanding fluid behavior in microscale applications. Rarefied regimes are characterized by a decrease in molecular collisions, and they lead to unusual phenomena such as gas phase separation, which is not acknowledged in hydrodynamic equations. In this work, numerical investigation of miscible gaseous mixtures in the rarefied regime is performed using a modified lattice Boltzmann model. Slip boundary conditions are adapted to arbitrary geometries. A ray-tracing algorithm-based wall function is implemented to model the non-equilibrium effects in the transition flow regime. The molecular free flow defined by the Knudsen diffusion coefficient is integrated through an effective and asymmetrical binary diffusion coefficient. The numerical model is validated with mass flow measurements through microchannels of different cross-section shapes from the near-continuum to the transition regimes, and gas phase separation is studied within a staggered arrangement of spheres. The influence of porosity and mixture composition on the gas separation effect are analyzed. Numerical results highlight the increase in the degree of gas phase separation with the rarefaction rate and the molecular mass ratio. The various simulations also indicate that geometrical features in porous media have a greater impact on gaseous mixtures’ effective permeability at highly rarefied regimes. Finally, a permeability enhancement factor based on the lightest species of the gaseous mixture is derived.
Open AccessLattice Boltzmann Model for Rarefied Gaseous Mixture Flows in Three-Dimensional Porous Media Including Knudsen Diffusion
Numerical modeling of gas flows in rarefied regimes is crucial in understanding fluid behavior in microscale applications. Rarefied regimes are characterized by a decrease in molecular collisions, and they lead to unusual phenomena such as gas phase separation, which is not acknowledged in hydrodynamic equations. In this work, numerical investigation of miscible gaseous mixtures in the rarefied regime is performed using a modified lattice Boltzmann model. Slip boundary conditions are adapted to arbitrary geometries. A ray-tracing algorithm-based wall function is implemented to model the non-equilibrium effects in the transition flow regime. The molecular free flow defined by the Knudsen diffusion coefficient is integrated through an effective and asymmetrical binary diffusion coefficient. The numerical model is validated with mass flow measurements through microchannels of different cross-section shapes from the near-continuum to the transition regimes, and gas phase separation is studied within a staggered arrangement of spheres. The influence of porosity and mixture composition on the gas separation effect are analyzed. Numerical results highlight the increase in the degree of gas phase separation with the rarefaction rate and the molecular mass ratio. The various simulations also indicate that geometrical features in porous media have a greater impact on gaseous mixtures’ effective permeability at highly rarefied regimes. Finally, a permeability enhancement factor based on the lightest species of the gaseous mixture is derived.
- 1 January 2017
- Published by Elsevier in Journal of Computational Physics
- Vol. 329, 16-28
A simple extension of Roe's scheme for real gases
- 1 January 2017
- Published by Elsevier in Journal of Computational Physics
- Vol. 329, 16-28
A simple extension of Roe's scheme for real gases
- 3 November 2015
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 138 (5) , 052604
Undergraduate Project in Compressor Rig Design, Fabrication, and Testing for Complete Engineering Training
An ambitious project in propulsion was introduced as part of the final-year integrator project offerings of the mechanical and aerospace engineering programs at École Polytechnique de Montréal in 2011–2012. It has been running successfully for the past three academic years. The project consists in the design, fabrication, and placement into service of a functional instrumented multistage compressor test rig, including the compressor, for research in compressor aerodynamics. A team of 15–17 senior-year undergraduate engineering students is given a set of design and performance specifications and measurement requirements, an electric motor and drive, a data acquisition system, and some measurement probes. They must complete the project in two semesters with a budget on the order of Can$15,000. The compressor is made from rapid prototyping to keep production cost and time reasonable. However, the required rotation speed of 7200 rpm stretches the limits of the plastic material and presents the same structural challenges as industrial compressors running at higher speeds. The students are split into subteams according to the required disciplines, namely, compressor aerodynamics, general aerodynamics, structures, dynamics, mechanical design and integration, instrumentation, and project management. For the initial phase, which covers the first two months, the students receive short seminars from experts in academia and industry in each discipline and use the knowledge from fundamental engineering courses to analytically model the different components to come up with a preliminary design. In the second phase, covering three to six, the students are trained at commercial simulation tools and use them for detailed analysis to refine and finalize the design. In each of the first two phases, the students present their work in design reviews with a jury made up of engineers from industry and supervising professors. During the final phase, the compressor is built and tested with data acquisition and motor control programs written by the students. Finally, the students present their results with comparison of measured performance with numerical and analytical predictions from the first two phases and hand over their compressor rig with design and test reports as well as a user manual and an assembly/maintenance manual. This complete project allows the students to put into practice virtually all the courses of their undergraduate engineering curriculum while giving them an extensive taste of the rich and intellectually challenging environment of gas turbine and turbomachinery engineering.
- 3 November 2015
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 138 (5) , 052604
Undergraduate Project in Compressor Rig Design, Fabrication, and Testing for Complete Engineering Training
An ambitious project in propulsion was introduced as part of the final-year integrator project offerings of the mechanical and aerospace engineering programs at École Polytechnique de Montréal in 2011–2012. It has been running successfully for the past three academic years. The project consists in the design, fabrication, and placement into service of a functional instrumented multistage compressor test rig, including the compressor, for research in compressor aerodynamics. A team of 15–17 senior-year undergraduate engineering students is given a set of design and performance specifications and measurement requirements, an electric motor and drive, a data acquisition system, and some measurement probes. They must complete the project in two semesters with a budget on the order of Can$15,000. The compressor is made from rapid prototyping to keep production cost and time reasonable. However, the required rotation speed of 7200 rpm stretches the limits of the plastic material and presents the same structural challenges as industrial compressors running at higher speeds. The students are split into subteams according to the required disciplines, namely, compressor aerodynamics, general aerodynamics, structures, dynamics, mechanical design and integration, instrumentation, and project management. For the initial phase, which covers the first two months, the students receive short seminars from experts in academia and industry in each discipline and use the knowledge from fundamental engineering courses to analytically model the different components to come up with a preliminary design. In the second phase, covering three to six, the students are trained at commercial simulation tools and use them for detailed analysis to refine and finalize the design. In each of the first two phases, the students present their work in design reviews with a jury made up of engineers from industry and supervising professors. During the final phase, the compressor is built and tested with data acquisition and motor control programs written by the students. Finally, the students present their results with comparison of measured performance with numerical and analytical predictions from the first two phases and hand over their compressor rig with design and test reports as well as a user manual and an assembly/maintenance manual. This complete project allows the students to put into practice virtually all the courses of their undergraduate engineering curriculum while giving them an extensive taste of the rich and intellectually challenging environment of gas turbine and turbomachinery engineering.
- 1 March 2015
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 28 (2)
Framework for the Robust Design Optimization of an Airframe and its Engines
Optimization studies for the next generation of aircraft and engine families are typically associated with the addition of technological advances to improve fuel efficiency, noise levels, and overall aircraft economics. In the conceptual study phase, the optimization process must address the uncertainties related to the anticipation of market requirements and potential technological advances at the time of entry into service, along with the fidelity of the modeling applied in the analysis. The current paper presents a framework using a robust design optimization methodology to mitigate these uncertainties when an airframe and its engines are designed jointly. The optimization of a 70 passenger aircraft illustrates the approach with a formulation seeking to optimize the design while attenuating its sensitivity to the potentially adverse effects of uncertainties.
- 1 March 2015
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 28 (2)
Framework for the Robust Design Optimization of an Airframe and its Engines
Optimization studies for the next generation of aircraft and engine families are typically associated with the addition of technological advances to improve fuel efficiency, noise levels, and overall aircraft economics. In the conceptual study phase, the optimization process must address the uncertainties related to the anticipation of market requirements and potential technological advances at the time of entry into service, along with the fidelity of the modeling applied in the analysis. The current paper presents a framework using a robust design optimization methodology to mitigate these uncertainties when an airframe and its engines are designed jointly. The optimization of a 70 passenger aircraft illustrates the approach with a formulation seeking to optimize the design while attenuating its sensitivity to the potentially adverse effects of uncertainties.
- 8 September 2013
- Published by Springer Nature in Journal of Scientific Computing
- Vol. 59 (3) , 545-573
High Order Spatial Generalization of 2D and 3D Isotropic Discrete Gradient Operators with Fast Evaluation on GPUs
- 8 September 2013
- Published by Springer Nature in Journal of Scientific Computing
- Vol. 59 (3) , 545-573
High Order Spatial Generalization of 2D and 3D Isotropic Discrete Gradient Operators with Fast Evaluation on GPUs
- 11 September 2012
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Conceptual Design Framework for Blended Wing Body Aircraft
- 11 September 2012
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Conceptual Design Framework for Blended Wing Body Aircraft
- Open Access
- 1 January 2011
- Published by Wiley in Modelling and Simulation in Engineering
- Vol. 2011 (1)
Comparison of Two Models for Radiative Heat Transfer in High Temperature Thermal Plasmas
Numerical simulation of the arc‐flow interaction in high‐voltage circuit breakers requires a radiation model capable of handling high‐temperature participating thermal plasmas. The modeling of the radiative transfer plays a critical role in the overall accuracy of such CFD simulations. As a result of the increase of computational power, CPU intensive methods based on the radiative transfer equation, leading to more accurate results, are now becoming attractive alternatives to current approximate models. In this paper, the predictive capabilities of the finite volume method (RTE‐FVM) and the P1 model are investigated. A systematic comparison between these two models and analytical solutions are presented for a variety of relevant test cases. Two implementations of each approach are compared, and a critical evaluation is presented.
- 1 January 2011
- Published by Wiley in Modelling and Simulation in Engineering
- Vol. 2011 (1)
Open AccessComparison of Two Models for Radiative Heat Transfer in High Temperature Thermal Plasmas
Numerical simulation of the arc‐flow interaction in high‐voltage circuit breakers requires a radiation model capable of handling high‐temperature participating thermal plasmas. The modeling of the radiative transfer plays a critical role in the overall accuracy of such CFD simulations. As a result of the increase of computational power, CPU intensive methods based on the radiative transfer equation, leading to more accurate results, are now becoming attractive alternatives to current approximate models. In this paper, the predictive capabilities of the finite volume method (RTE‐FVM) and the P1 model are investigated. A systematic comparison between these two models and analytical solutions are presented for a variety of relevant test cases. Two implementations of each approach are compared, and a critical evaluation is presented.
- 1 December 2006
- Published by Springer Nature in Optimization and Engineering
- Vol. 7 (4) , 479-500
Variable-fidelity optimization: Efficiency and robustness
- 1 December 2006
- Published by Springer Nature in Optimization and Engineering
- Vol. 7 (4) , 479-500
Variable-fidelity optimization: Efficiency and robustness
- 26 September 2006
- Published by Springer Nature
- p. 415-421
A NURBS-Based Shape Optimization Method for Hydraulic Turbine Stay Vane
- 26 September 2006
- Published by Springer Nature
- p. 415-421
A NURBS-Based Shape Optimization Method for Hydraulic Turbine Stay Vane
- 1 December 2005
- Published by Taylor & Francis in Engineering Optimization
- Vol. 37 (8) , 775-796
Decomposition of multidisciplinary optimization problems: formulations and application to a simplified wing design
Several formulations for solving multidisciplinary design optimization (MDO) problems are presented and applied to a test case. Two bi-level hierarchical decomposition approaches are compared with two classical single-level approaches without decomposition of the optimization problem. A methodology to decompose MDO problems and a new formulation based on this decomposition are proposed. The problem considered here for validation of the different formulations involves the shape and structural optimization of a conceptual wing model. The efficiency of the design strategies are compared on the basis of optimization results.
- 1 December 2005
- Published by Taylor & Francis in Engineering Optimization
- Vol. 37 (8) , 775-796
Decomposition of multidisciplinary optimization problems: formulations and application to a simplified wing design
Several formulations for solving multidisciplinary design optimization (MDO) problems are presented and applied to a test case. Two bi-level hierarchical decomposition approaches are compared with two classical single-level approaches without decomposition of the optimization problem. A methodology to decompose MDO problems and a new formulation based on this decomposition are proposed. The problem considered here for validation of the different formulations involves the shape and structural optimization of a conceptual wing model. The efficiency of the design strategies are compared on the basis of optimization results.