Katrin Schönfeld
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Katrin Schönfeld has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Michaelis
Technische Universität Dresden
4 shared publications - Hagen Klemm
Fraunhofer Society
3 shared publications Andreas Nöth
2 shared publications- Chokri Cherif
Institute of Textile Machinery and High Performance Material Technology, TUD Dresden University of Technology, 01069 Dresden, Germany
2 shared publications Hagen Klemm
2 shared publicationsJonathan Maier
2 shared publications
Latest Publications
- Open Access
- 15 December 2021
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 52 (12) , 1338-1345
Electrical performance of ZrC ceramics
In the present study it was possible to provide evidence that ZrC ceramics – regarding their electrical‐mechanical and thermal properties – are an attractive substitute for tungsten and molybdenum in the field of refractory materials and heating elements. For this purpose, the heating behavior of ZrC materials was investigated in a specific test stand under high vacuum conditions (10−6 mbar) at temperatures above 2000 °C. In addition, the applicability of ZrC as an electrical heating element was investigated in terms of geometric design and long‐term behavior. Examinations after the heating tests did not reveal any significant changes in the material.
- 15 December 2021
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 52 (12) , 1338-1345
Open AccessElectrical performance of ZrC ceramics
In the present study it was possible to provide evidence that ZrC ceramics – regarding their electrical‐mechanical and thermal properties – are an attractive substitute for tungsten and molybdenum in the field of refractory materials and heating elements. For this purpose, the heating behavior of ZrC materials was investigated in a specific test stand under high vacuum conditions (10−6 mbar) at temperatures above 2000 °C. In addition, the applicability of ZrC as an electrical heating element was investigated in terms of geometric design and long‐term behavior. Examinations after the heating tests did not reveal any significant changes in the material.
- 1 May 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (5) , 2988-2994
Wet chemical deposition of BN, SiC and Si3N4 interphases on SiC fibers
- 1 May 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (5) , 2988-2994
Wet chemical deposition of BN, SiC and Si3N4 interphases on SiC fibers
- Open Access
Delayed Formation of Thermally Grown Oxide in Environmental Barrier Coatings for Non-Oxide Ceramic Matrix Composites
The oxidation and corrosion behavior at elevated temperatures of a SiCF/SiC(N) composite with two plasma-sprayed environmental barrier coating (EBC) systems were studied. After both processes, the formation of a silica-based thermally grown oxide (TGO) layer was observed. The formation of this TGO caused two principal failure mechanisms of the EBC. Firstly, spallation of the EBC induced by stresses from volume expansion and phase transformation to crystalline SiO2 was observed. Water vapor corrosion of the TGO with gap formation in the top region of the TGO was found to be a second failure mechanism. After a burner rig test of the Al2O3-YAG EBC system, this corrosion process was observed at the TGO surface and in the volume of the Al2O3 bond coat. In the case of the second system, Si-Yb2Si2O7/SiC-Yb2SiO5, the formation of the TGO could be delayed by introducing an additional intermediate layer based on Yb2Si2O7 filled with SiC particles. The SiC particles in the intermediate layer were oxidized and served as getter to reduce the permeation of oxidants (O2, H2O) into the material. In this way, the formation of the TGO and the failure mechanisms caused by their formation and growth could be delayed.
Open AccessDelayed Formation of Thermally Grown Oxide in Environmental Barrier Coatings for Non-Oxide Ceramic Matrix Composites
The oxidation and corrosion behavior at elevated temperatures of a SiCF/SiC(N) composite with two plasma-sprayed environmental barrier coating (EBC) systems were studied. After both processes, the formation of a silica-based thermally grown oxide (TGO) layer was observed. The formation of this TGO caused two principal failure mechanisms of the EBC. Firstly, spallation of the EBC induced by stresses from volume expansion and phase transformation to crystalline SiO2 was observed. Water vapor corrosion of the TGO with gap formation in the top region of the TGO was found to be a second failure mechanism. After a burner rig test of the Al2O3-YAG EBC system, this corrosion process was observed at the TGO surface and in the volume of the Al2O3 bond coat. In the case of the second system, Si-Yb2Si2O7/SiC-Yb2SiO5, the formation of the TGO could be delayed by introducing an additional intermediate layer based on Yb2Si2O7 filled with SiC particles. The SiC particles in the intermediate layer were oxidized and served as getter to reduce the permeation of oxidants (O2, H2O) into the material. In this way, the formation of the TGO and the failure mechanisms caused by their formation and growth could be delayed.
- 1 October 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (13) , 3557-3565
Interaction of fiber matrix bonding in SiC/SiC ceramic matrix composites
- 1 October 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (13) , 3557-3565
Interaction of fiber matrix bonding in SiC/SiC ceramic matrix composites
- 1 June 2019
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 809, 421-426
BN-Based Fiber Coatings by Wet-Chemical Coating
Fiber coatings for BN/SiC-and BN/Si3N4-bilayer systems were developed for the use in SiC/SiC composites. All coatings were produced with high process velocities of 500 m/h by a continuous roll-to-roll dip-coating process. The fiber surface was fully covered with a homogeneous coating and without fiber bridging. Tensile tests of fiber bundles were used to examine potential degradation of the fiber properties due to the application of the coatings. The coated fiber bundles showed a reduction of the maximum tensile load to 90.0 % for the BN/Si3N4 and to 86.7 % for the BN/SiC coating in comparison to the fiber bundle in the as-received state. A thermal treatment of the coated fiber bundles up to 1650 °C led to no reduction of their maximum tensile load. SiC/SiC composites were fabricated by polymer infiltration and pyrolysis. The flexural strength and strain of composites with BN/SiC fiber coating were improved to 467 MPa and 0.42 % in comparison to the composites without fiber coating. The composites with BN/SiC coating showed toughened fracture behavior with fiber pull-out effects.
- 1 June 2019
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 809, 421-426
BN-Based Fiber Coatings by Wet-Chemical Coating
Fiber coatings for BN/SiC-and BN/Si3N4-bilayer systems were developed for the use in SiC/SiC composites. All coatings were produced with high process velocities of 500 m/h by a continuous roll-to-roll dip-coating process. The fiber surface was fully covered with a homogeneous coating and without fiber bridging. Tensile tests of fiber bundles were used to examine potential degradation of the fiber properties due to the application of the coatings. The coated fiber bundles showed a reduction of the maximum tensile load to 90.0 % for the BN/Si3N4 and to 86.7 % for the BN/SiC coating in comparison to the fiber bundle in the as-received state. A thermal treatment of the coated fiber bundles up to 1650 °C led to no reduction of their maximum tensile load. SiC/SiC composites were fabricated by polymer infiltration and pyrolysis. The flexural strength and strain of composites with BN/SiC fiber coating were improved to 467 MPa and 0.42 % in comparison to the composites without fiber coating. The composites with BN/SiC coating showed toughened fracture behavior with fiber pull-out effects.
- Open Access
- 16 June 2017
- Published by Tsinghua University Press in Journal of Advanced Ceramics
- Vol. 6 (2) , 165-175
Pressureless sintering of ZrC with variable stoichiometry
This paper presents the experiments on the synthesis of zirconium carbide (ZrC) using carbothermal reduction of zirconia (ZrO2). The ratio of ZrO2:C is used to adapt ZrCxOy with x < 1 or ZrC + C. The modification of ZrCxOy and the total carbon amount allows the use of pressureless sintering method in combination with sintering temperatures ≤ 2000 °C. Fully densified ZrC products are obtained. The relevant details of ZrC formation are investigated by X-ray diffraction (XRD). The sintered products are characterized by XRD, field emission scanning electron microscopy (FESEM), as well as mechanical and electrical methods. XRD and FESEM investigations show that ZrCxOy is formed during the manufacturing process. The grain size and additional zirconia or carbon are related to the ZrO2:C ratio of the starting powder mixture. Bending strength up to 300 MPa, Young’s modulus up to 400 GPa, fracture toughness up to 4.1 MPa·m1/2, and electrical resistance at room temperature around 10−4 Ω·cm are reached by the pressureless sintered ZrC.
- 16 June 2017
- Published by Tsinghua University Press in Journal of Advanced Ceramics
- Vol. 6 (2) , 165-175
Open AccessPressureless sintering of ZrC with variable stoichiometry
This paper presents the experiments on the synthesis of zirconium carbide (ZrC) using carbothermal reduction of zirconia (ZrO2). The ratio of ZrO2:C is used to adapt ZrCxOy with x < 1 or ZrC + C. The modification of ZrCxOy and the total carbon amount allows the use of pressureless sintering method in combination with sintering temperatures ≤ 2000 °C. Fully densified ZrC products are obtained. The relevant details of ZrC formation are investigated by X-ray diffraction (XRD). The sintered products are characterized by XRD, field emission scanning electron microscopy (FESEM), as well as mechanical and electrical methods. XRD and FESEM investigations show that ZrCxOy is formed during the manufacturing process. The grain size and additional zirconia or carbon are related to the ZrO2:C ratio of the starting powder mixture. Bending strength up to 300 MPa, Young’s modulus up to 400 GPa, fracture toughness up to 4.1 MPa·m1/2, and electrical resistance at room temperature around 10−4 Ω·cm are reached by the pressureless sintered ZrC.
- 1 May 2017
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 96, 37-45
Optimization of the temperature program to scale up the stabilization of polyacrylonitrile fibers
- 1 May 2017
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 96, 37-45
Optimization of the temperature program to scale up the stabilization of polyacrylonitrile fibers
- 15 April 2016
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 133 (29)
Characteristics of wet‐spun and thermally treated poly acrylonitrile fibers
The performance of carbon fibers depends on the quality of the precursor and the conditions of the thermal treatment. In detail, for a PAN precursor fiber the viscosity of a spinning dope and the draw ratio during the spinning process needs to be considered. Through wet spinning, different types of PAN precursor fibers with defined spinning parameters, including solid content, solvent content in a bath, and especially draw ratio resulting in defined cross section diameters, were fabricated and analyzed with tensile tests, density investigations, SEM, TGA‐MS, FTIR, and XRD. The results show that the mechanical properties of the fibers correlate to crystallinity. The cross section diameter is strongly related to the morphology of the fibers after thermal treatment. By extending the postdrawing of PAN fibers high tenacities were obtained at the cost of the cross section shape. In addition, TGA measurements reveal trapped residues of the wet spinning process as well as show several chemical reactions takes place at the same time at different temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43698.
- 15 April 2016
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 133 (29)
Characteristics of wet‐spun and thermally treated poly acrylonitrile fibers
The performance of carbon fibers depends on the quality of the precursor and the conditions of the thermal treatment. In detail, for a PAN precursor fiber the viscosity of a spinning dope and the draw ratio during the spinning process needs to be considered. Through wet spinning, different types of PAN precursor fibers with defined spinning parameters, including solid content, solvent content in a bath, and especially draw ratio resulting in defined cross section diameters, were fabricated and analyzed with tensile tests, density investigations, SEM, TGA‐MS, FTIR, and XRD. The results show that the mechanical properties of the fibers correlate to crystallinity. The cross section diameter is strongly related to the morphology of the fibers after thermal treatment. By extending the postdrawing of PAN fibers high tenacities were obtained at the cost of the cross section shape. In addition, TGA measurements reveal trapped residues of the wet spinning process as well as show several chemical reactions takes place at the same time at different temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43698.
- 1 October 2014
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 34 (12) , 2913-2924
Laser-supported joining of SiC-fiber/SiCN ceramic matrix composites fabricated by precursor infiltration
- 1 October 2014
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 34 (12) , 2913-2924
Laser-supported joining of SiC-fiber/SiCN ceramic matrix composites fabricated by precursor infiltration