Shamsul Akmar Ab Aziz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shamsul Akmar Ab Aziz has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Mohd Jailani Mohd Nor
Department of Mechanical and Material Engineering National University of Malaysia UKM Bangi Malaysia
6 shared publications Mohd Zaki Nuawi
6 shared publications- Dian Darina Indah Daruis
Faculty of Engineering, Universiti Pertahanan Nasional Malaysia, Kem Sungai Besi, Kuala Lumpur, Malaysia
2 shared publications Abdul Rahim Bahari
Universiti Kebangsaan Malaysia
1 shared publicationAizul Fazli Suhaimi
STRIDE
1 shared publicationDian Darina Indah Daruis
National Defence University of Malaysia (UPNM), Sungai Besi Camp, 57000 Kuala Lumpur, Malaysia
1 shared publication
Latest Publications
- 1 March 2017
- Published by International Institute of Acoustics and Vibration (IIAV) in The International Journal of Acoustics and Vibration
- Vol. 22 (1)
Monitoring Of Hand-Arm Vibration
- 1 March 2017
- Published by International Institute of Acoustics and Vibration (IIAV) in The International Journal of Acoustics and Vibration
- Vol. 22 (1)
Monitoring Of Hand-Arm Vibration
- 1 November 2015
- Published by Oxford University Press (OUP) in Journal of Occupational Health
- Vol. 57 (6) , 513-520
New regression model for predicting hand‐arm vibration (HAV) of Malaysian Army (MA) three‐tonne truck steering wheels
New regression model for predicting hand‐arm vibration (HAV) of Malaysian Army (MA) three‐tonne truck steering wheels: Shamsul Akmar Ab Aziz, et al. Department of Mechanical and Material Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia (UKM), MalaysiaObjective: The objective of this study was to present a new method for determination of hand‐arm vibration (HAV) in Malaysian Army (MA) three‐tonne truck steering wheels based on changes in vehicle speed using regression model and the statistical analysis method known as Integrated Kurtosis‐Based Algorithm for Z‐Notch Filter Technique Vibro (I‐kaz Vibro).Methodology: The test was conducted for two different road conditions, tarmac and dirt roads. HAV exposure was measured using a Brüel & Kjær Type 3649 vibration analyzer, which is capable of recording HAV exposures from steering wheels. The data was analyzed using Ikaz Vibro to determine the HAV values in relation to varying speeds of a truck and to determine the degree of data scattering for HAV data signals.Results: Based on the results obtained, HAV experienced by drivers can be determined using the daily vibration exposure A(8), I‐kaz Vibro coefficient (Ƶv ∞), and the I‐kaz Vibro display. The I‐kaz Vibro displays also showed greater scatterings, indicating that the values of Ƶv ∞ and A(8) were increasing. Prediction of HAV exposure was done using the developed regression model and graphical representations of Ƶv ∞. The results of the regression model showed that Ƶ∞ increased when the vehicle speed and HAV exposure increased.Discussion: For model validation, predicted and measured noise exposures were compared, and high coefficient of correlation (R2) values were obtained, indicating that good agreement was obtained between them. By using the developed regression model, we can easily predict HAV exposure from steering wheels for HAV exposure monitoring.
- 1 November 2015
- Published by Oxford University Press (OUP) in Journal of Occupational Health
- Vol. 57 (6) , 513-520
New regression model for predicting hand‐arm vibration (HAV) of Malaysian Army (MA) three‐tonne truck steering wheels
New regression model for predicting hand‐arm vibration (HAV) of Malaysian Army (MA) three‐tonne truck steering wheels: Shamsul Akmar Ab Aziz, et al. Department of Mechanical and Material Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia (UKM), MalaysiaObjective: The objective of this study was to present a new method for determination of hand‐arm vibration (HAV) in Malaysian Army (MA) three‐tonne truck steering wheels based on changes in vehicle speed using regression model and the statistical analysis method known as Integrated Kurtosis‐Based Algorithm for Z‐Notch Filter Technique Vibro (I‐kaz Vibro).Methodology: The test was conducted for two different road conditions, tarmac and dirt roads. HAV exposure was measured using a Brüel & Kjær Type 3649 vibration analyzer, which is capable of recording HAV exposures from steering wheels. The data was analyzed using Ikaz Vibro to determine the HAV values in relation to varying speeds of a truck and to determine the degree of data scattering for HAV data signals.Results: Based on the results obtained, HAV experienced by drivers can be determined using the daily vibration exposure A(8), I‐kaz Vibro coefficient (Ƶv ∞), and the I‐kaz Vibro display. The I‐kaz Vibro displays also showed greater scatterings, indicating that the values of Ƶv ∞ and A(8) were increasing. Prediction of HAV exposure was done using the developed regression model and graphical representations of Ƶv ∞. The results of the regression model showed that Ƶ∞ increased when the vehicle speed and HAV exposure increased.Discussion: For model validation, predicted and measured noise exposures were compared, and high coefficient of correlation (R2) values were obtained, indicating that good agreement was obtained between them. By using the developed regression model, we can easily predict HAV exposure from steering wheels for HAV exposure monitoring.
- Open Access
- 16 April 2014
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 6, 616093
New Regression Models for Predicting Noise Exposure in the Driver's Compartment of Malaysian Army Three-Tonne Trucks
The objective of this study is to present a new method for determination of noise exposure in the driver’s compartment of Malaysian Army (MA) three-tonne trucks based on changing vehicle speed using regression models and the statistical analysis method known as Integrated Kurtosis-based Algorithm for -notch filter (I-kaz). The test was conducted on two different road conditions: tarmac and dirt roads. Noise exposure was measured using a sound level meter which is capable of recording raw sound pressure in Pa, and comparisons were made between the two types of roads. The prediction of noise exposure was done using the developed regression models and 3D graphic representations of the I-kaz coefficient . The results of the regression models show that increases when vehicle speed and noise exposure increase. For model validation, predicted and measured noise exposures were compared, and a relatively good agreement has been obtained between them. It was found that the predictions had high accuracies and low average relative errors. By using the regression models, we can easily predict noise exposure inside the truck driver’s compartment. The proposed models are efficient and can be extended to the automotive industry for noise exposure monitoring.
- 16 April 2014
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 6, 616093
Open AccessNew Regression Models for Predicting Noise Exposure in the Driver's Compartment of Malaysian Army Three-Tonne Trucks
The objective of this study is to present a new method for determination of noise exposure in the driver’s compartment of Malaysian Army (MA) three-tonne trucks based on changing vehicle speed using regression models and the statistical analysis method known as Integrated Kurtosis-based Algorithm for -notch filter (I-kaz). The test was conducted on two different road conditions: tarmac and dirt roads. Noise exposure was measured using a sound level meter which is capable of recording raw sound pressure in Pa, and comparisons were made between the two types of roads. The prediction of noise exposure was done using the developed regression models and 3D graphic representations of the I-kaz coefficient . The results of the regression models show that increases when vehicle speed and noise exposure increase. For model validation, predicted and measured noise exposures were compared, and a relatively good agreement has been obtained between them. It was found that the predictions had high accuracies and low average relative errors. By using the regression models, we can easily predict noise exposure inside the truck driver’s compartment. The proposed models are efficient and can be extended to the automotive industry for noise exposure monitoring.
- 1 December 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 471, 74-80
Study of Noise, Vibration and Harshness (NVH) for Malaysian Army (MA) 3-Tonne Trucks
Moving vehicle will produce dynamic excitation and can be categorized in the study of noise, vibration and harshness (NVH). Studies of NVH can resolve issues associated with the use of a vehicle comfort. Exposure to some level of noise and vibration can be classified as a danger to vehicle passengers if they are exposed in a standard eight-hour time period. Therefore NVH aspect is the most important aspect in selecting a military vehicle other than the factor of safety, reliability, fuel consumption and maintenance costs. This study was carried out on Malaysian Army (MA) 3-tonne truck drivers who are exposed to noise and vibration produced by the truck. Vibration exposure at seat, steering wheel and body floor was measured using tri-axial and single axis accelerometers which were connected to a Brüel & Kjær Type 3649 vibration analyser, while noise exposure was measured at the drivers ear position using a DuO smart noise monitor. From the results obtained, both vibration and noise pressure levels increased proportionally with the increasing speed of the truck. In the long-term, will have an impact on the health of the truck drivers.
- 1 December 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 471, 74-80
Study of Noise, Vibration and Harshness (NVH) for Malaysian Army (MA) 3-Tonne Trucks
Moving vehicle will produce dynamic excitation and can be categorized in the study of noise, vibration and harshness (NVH). Studies of NVH can resolve issues associated with the use of a vehicle comfort. Exposure to some level of noise and vibration can be classified as a danger to vehicle passengers if they are exposed in a standard eight-hour time period. Therefore NVH aspect is the most important aspect in selecting a military vehicle other than the factor of safety, reliability, fuel consumption and maintenance costs. This study was carried out on Malaysian Army (MA) 3-tonne truck drivers who are exposed to noise and vibration produced by the truck. Vibration exposure at seat, steering wheel and body floor was measured using tri-axial and single axis accelerometers which were connected to a Brüel & Kjær Type 3649 vibration analyser, while noise exposure was measured at the drivers ear position using a DuO smart noise monitor. From the results obtained, both vibration and noise pressure levels increased proportionally with the increasing speed of the truck. In the long-term, will have an impact on the health of the truck drivers.
- 1 December 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 471, 156-160
Correlation between Whole Body Vibration Exposure and I-KazTM 3D Coefficient for Malaysian Army 3-Tonne Truck Drivers
Exposure to high levels of whole body vibration (WBV) from the seat can present risks to health and safety and cause injuries to drivers. This study presents a study on WBV exposure to Malaysian Army 3-tonne truck drivers using the method defined in International Standard ISO 2631-1:1997. The vehicle that was chosen for this study was based on the highest number of vehicles available within the Malaysian Army services. 3-tonne truck is the most widely used in Malaysian Army services. WBV from the drivers were measured using tri-axial accelerometer and was connected to Brüel & Kjær Vibration Analyser Type 3649, which is capable to produce raw data to calculate the vibration dose value (VDV). The raw data from each axis were analyzed using statistical analysis method, Integrated Kurtosis Algorithm for Z-notch Filter (I-kazTM) 3D to determine the vibration values in relation to varying speed of the vehicle. Based on the results, WBV experienced by the drivers can be presented in VDV and I-kazTM 3D coefficient which the value will increase proportional to the truck speed.
- 1 December 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 471, 156-160
Correlation between Whole Body Vibration Exposure and I-KazTM 3D Coefficient for Malaysian Army 3-Tonne Truck Drivers
Exposure to high levels of whole body vibration (WBV) from the seat can present risks to health and safety and cause injuries to drivers. This study presents a study on WBV exposure to Malaysian Army 3-tonne truck drivers using the method defined in International Standard ISO 2631-1:1997. The vehicle that was chosen for this study was based on the highest number of vehicles available within the Malaysian Army services. 3-tonne truck is the most widely used in Malaysian Army services. WBV from the drivers were measured using tri-axial accelerometer and was connected to Brüel & Kjær Vibration Analyser Type 3649, which is capable to produce raw data to calculate the vibration dose value (VDV). The raw data from each axis were analyzed using statistical analysis method, Integrated Kurtosis Algorithm for Z-notch Filter (I-kazTM) 3D to determine the vibration values in relation to varying speed of the vehicle. Based on the results, WBV experienced by the drivers can be presented in VDV and I-kazTM 3D coefficient which the value will increase proportional to the truck speed.
- 1 April 2012
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 165, 323-329
Design of Special Purpose off Road Vehicle (SPORV) for Unmanned Ground Vehicle Application
This paper describes the design of a Special Purpose Off Road Vehicle which was developed as the main body for an Unmanned Ground Vehicle. The stringent requirement for off-road capabilities and the need to incorporate a plethora of vision based sensing mechanism was the main design criteria that were fulfilled by the Special Purpose Off Road Vehicle. The Special Purpose Off Road Vehicle is incorporated with a host of actuators, instrumentation and drive circuits, Data Acquisition System and remote communication and control module. The Special Purpose Off Road Vehicle is also equipped with an onboard 2 GHZ Pentium Core 2 Duo Processor Class PC that serves as the main controller when it is operated in the UGV mode. The final prototype unit of the Special Purpose Off Road Vehicle was successfully designed, developed and fabricated according to the set requirement and is used as a research prototype unit at Science and Technology Research Institute for Defence, Ministry Of Defence, Malaysia.
- 1 April 2012
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 165, 323-329
Design of Special Purpose off Road Vehicle (SPORV) for Unmanned Ground Vehicle Application
This paper describes the design of a Special Purpose Off Road Vehicle which was developed as the main body for an Unmanned Ground Vehicle. The stringent requirement for off-road capabilities and the need to incorporate a plethora of vision based sensing mechanism was the main design criteria that were fulfilled by the Special Purpose Off Road Vehicle. The Special Purpose Off Road Vehicle is incorporated with a host of actuators, instrumentation and drive circuits, Data Acquisition System and remote communication and control module. The Special Purpose Off Road Vehicle is also equipped with an onboard 2 GHZ Pentium Core 2 Duo Processor Class PC that serves as the main controller when it is operated in the UGV mode. The final prototype unit of the Special Purpose Off Road Vehicle was successfully designed, developed and fabricated according to the set requirement and is used as a research prototype unit at Science and Technology Research Institute for Defence, Ministry Of Defence, Malaysia.
- 1 April 2012
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 165, 165-169
Noise, Vibration and Harshness (NVH) Study on Malaysian Armed Forces (MAF) Tactical Vehicle
Noise, Vibration and Harshness (NVH) is the study and modification of the noise and vibration characteristics of vehicles, particularly cars and trucks. NVH parameters which consist of noise (unwanted sound), vibration (mechanical oscillation) and harshness (severity or discomfort of noise or vibration) need to be evaluated in order to improve comfort and safety levels for vehicle occupants. In this paper, NVH study was conducted on Malaysian Armed Forces (MAF) tactical vehicles in order to ensure that the vehicles meet the requirements of the Occupational Safety and Health Administration (OSHA) and Directive 2002/44/EC. The project aim was to identify the preferable solution that can improve the NVH parameters of the vehicles in accordance to the standard and test protocols. A 4x4 Troop Transporter vehicle which carried 8 persons at the rear cabin was used in the NVH testing. The vibration parameters studied are hand arm vibration (HAV), focussing on vibration on the steering wheels of the vehicle, and whole body vibration (WBV), focussing on vibration on the seats. For noise, it was measured at the driver cabin and rear cabin of the vehicles. From the results, the HAV value for driver during idle speed was found to be higher than the others velocity. For WBV, vibration value for passenger 1 in rear cabin was highest compared to the other WBV test points.
- 1 April 2012
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 165, 165-169
Noise, Vibration and Harshness (NVH) Study on Malaysian Armed Forces (MAF) Tactical Vehicle
Noise, Vibration and Harshness (NVH) is the study and modification of the noise and vibration characteristics of vehicles, particularly cars and trucks. NVH parameters which consist of noise (unwanted sound), vibration (mechanical oscillation) and harshness (severity or discomfort of noise or vibration) need to be evaluated in order to improve comfort and safety levels for vehicle occupants. In this paper, NVH study was conducted on Malaysian Armed Forces (MAF) tactical vehicles in order to ensure that the vehicles meet the requirements of the Occupational Safety and Health Administration (OSHA) and Directive 2002/44/EC. The project aim was to identify the preferable solution that can improve the NVH parameters of the vehicles in accordance to the standard and test protocols. A 4x4 Troop Transporter vehicle which carried 8 persons at the rear cabin was used in the NVH testing. The vibration parameters studied are hand arm vibration (HAV), focussing on vibration on the steering wheels of the vehicle, and whole body vibration (WBV), focussing on vibration on the seats. For noise, it was measured at the driver cabin and rear cabin of the vehicles. From the results, the HAV value for driver during idle speed was found to be higher than the others velocity. For WBV, vibration value for passenger 1 in rear cabin was highest compared to the other WBV test points.