Alexander Vakhrushev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alexander Vakhrushev has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
- Abdellah Kharicha
Department of Metallurgy Technical University of Leoben Leoben Austria
16 shared publications Ebrahim Karimi-Sibaki
15 shared publications- Menghuai Wu
Department of Metallurgy, University of Leoben, A-8700 Leoben, Austria
15 shared publications Andreas Ludwig
Chair of Simulation and Modeling of Metallurgical Processes, Montanunivesität Leoben, Leoben, Austria
14 shared publicationsMenghuai Wu
14 shared publications- Andreas Ludwig
Department Metallurgy, University of Leoben, Leoben, Austria
11 shared publications
Latest Publications
- Open Access
- 16 September 2026
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 32
Rapid prediction of maximal temperature in liquid-cooled Li-Ion battery modules: a case study using polymeric hollow fiber cooling channels
- 16 September 2026
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 32
Open AccessRapid prediction of maximal temperature in liquid-cooled Li-Ion battery modules: a case study using polymeric hollow fiber cooling channels
- Open Access
- 10 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 31
Quantitative impact of hydrogen on voltage characteristics and arc stability in industrial EAFs and HPSR
- 10 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 31
Open AccessQuantitative impact of hydrogen on voltage characteristics and arc stability in industrial EAFs and HPSR
- Open Access
- 12 March 2026
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 358, 01002
From imaging to simulation: A workflow for converting CT/SEM data into OpenFOAM meshes
CT and SEM imaging often produce complex geometries, such as porous or irregular structures, which pose significant challenges for numerical simulations. In contrast to meshless methods like LBM or SPH, traditional FVM and FEM solvers require a high-quality computational mesh with consistent connectivity — a task that becomes particularly demanding for image-based data.This work presents a practical, step-by-step workflow for converting CT or SEM datasets into simulation-ready meshes for OpenFOAM. Two alternative meshing strategies are introduced, each discussed in terms of workflow complexity, mesh quality, and computational efficiency. The study aims to simplify the integration of experimental imaging and CFD modeling, bridging the gap between real microstructures and numerical analysis.
- 12 March 2026
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 358, 01002
Open AccessFrom imaging to simulation: A workflow for converting CT/SEM data into OpenFOAM meshes
CT and SEM imaging often produce complex geometries, such as porous or irregular structures, which pose significant challenges for numerical simulations. In contrast to meshless methods like LBM or SPH, traditional FVM and FEM solvers require a high-quality computational mesh with consistent connectivity — a task that becomes particularly demanding for image-based data.This work presents a practical, step-by-step workflow for converting CT or SEM datasets into simulation-ready meshes for OpenFOAM. Two alternative meshing strategies are introduced, each discussed in terms of workflow complexity, mesh quality, and computational efficiency. The study aims to simplify the integration of experimental imaging and CFD modeling, bridging the gap between real microstructures and numerical analysis.
- Open Access
- 18 August 2025
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 219
Inverse calculation of local heat transfer coefficient on generic surfaces in OpenFOAM
- 18 August 2025
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 219
Open AccessInverse calculation of local heat transfer coefficient on generic surfaces in OpenFOAM
- Open Access
- 22 June 2025
- Published by Elsevier in International Journal of Thermofluids
- Vol. 28
Magnetohydrodynamics phenomena in continuous casting process under applied electromagnetic braking (EMBr)
- 22 June 2025
- Published by Elsevier in International Journal of Thermofluids
- Vol. 28
Open AccessMagnetohydrodynamics phenomena in continuous casting process under applied electromagnetic braking (EMBr)
- Open Access
- 8 April 2025
- Published by Elsevier in Applied Mathematical Modelling
- Vol. 145
Refraction and reflection patterns of an inclined turbulent conductive jet induced by a local transverse magnetic field
- 8 April 2025
- Published by Elsevier in Applied Mathematical Modelling
- Vol. 145
Open AccessRefraction and reflection patterns of an inclined turbulent conductive jet induced by a local transverse magnetic field
- 1 January 2025
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 12 (1) , 22
Modeling Heat Transfer in Cylindrical Batteries: Spiral-Based Thermal Conductivity Tensor
The Volume 12, published for JFFHMT Journal.
- 1 January 2025
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 12 (1) , 22
Modeling Heat Transfer in Cylindrical Batteries: Spiral-Based Thermal Conductivity Tensor
The Volume 12, published for JFFHMT Journal.
- 1 November 2024
- Published by Avestia Publishing
Spiral Structure of Cylindrical Batteries and its Importance in Modeling of Heat Transfer
- 1 November 2024
- Published by Avestia Publishing
Spiral Structure of Cylindrical Batteries and its Importance in Modeling of Heat Transfer
- Open Access
- 2 May 2024
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 149 (11) , 5229-5238
Case study on thermal management of planar elements with various polymeric heat exchangers: experiment and simulation
A reliable battery thermal management system (BTMS) is essential to ensure proper performance, a long life span and high electric vehicle safety. The primary objective of BTMS is to maintain the cells’ temperature in the range of 15–35 °C while limiting the temperature spread between cells to below 5 °C. Active thermal management with polymeric hollow fibers (PHFs) has been reported in a few articles, but its tremendous flexibility is mainly advantageous for cylindrical cells. Extruded polymeric cold plate heat exchangers with rounded rectangle channels (RRCs) are proposed as a more elegant solution for planar batteries. Heat exchangers using PHFs and RRCs were experimentally compared, with a strong focus on minimizing the maximum temperature and temperature spread of the experimental setup while simultaneously achieving minimal pressure drops. The system behavior with different parameters, including materials, geometry and thermophysical properties, was further studied using properly validated CFD models.
- 2 May 2024
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 149 (11) , 5229-5238
Open AccessCase study on thermal management of planar elements with various polymeric heat exchangers: experiment and simulation
A reliable battery thermal management system (BTMS) is essential to ensure proper performance, a long life span and high electric vehicle safety. The primary objective of BTMS is to maintain the cells’ temperature in the range of 15–35 °C while limiting the temperature spread between cells to below 5 °C. Active thermal management with polymeric hollow fibers (PHFs) has been reported in a few articles, but its tremendous flexibility is mainly advantageous for cylindrical cells. Extruded polymeric cold plate heat exchangers with rounded rectangle channels (RRCs) are proposed as a more elegant solution for planar batteries. Heat exchangers using PHFs and RRCs were experimentally compared, with a strong focus on minimizing the maximum temperature and temperature spread of the experimental setup while simultaneously achieving minimal pressure drops. The system behavior with different parameters, including materials, geometry and thermophysical properties, was further studied using properly validated CFD models.
- Open Access
- 28 March 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (7) , 2831
Exploring Extreme Voltage Events in Hydrogen Arcs within Electric Arc Furnaces
This study highlights the potential utilization of hydrogen gas in electric arc furnaces for achieving cleaner and more sustainable steel production. The application of hydrogen offers a promising path for reducing carbon emissions, enhancing energy efficiency, and advancing the concept of “green steel”. This study employs a 2D axisymmetric induction-based model to simulate an electric arc under atmospheric pressure conditions. We conducted numerical simulations to compare compressible and incompressible models of an electric arc. The impact of compressibility on hydrogen arc characteristics such as arc velocity, temperature distribution, and voltage drop were investigated. Additionally, different applied current arcs were simulated using the compressible model. When compared to an incompressible arc, the compressible arc exhibits a higher voltage drop. This higher voltage drop is associated with lower temperatures and lower arc velocity. A rise in applied current results in an upward trend in the voltage drop and an increase in the arc radius. In addition, the increased applied current increases the probability of voltage fluctuations. The voltage fluctuations tend to become more extreme and exert more stress on the control circuit. This has an impact on emerging electric arc technologies, particularly those involving the use of hydrogen. These fluctuations affect arc stability, heat output, and the overall quality of processes. Thus, the precise prediction of voltage and the ability to stabilize the operation is critical for the successful implementation of new hydrogen technologies.
- 28 March 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (7) , 2831
Open AccessExploring Extreme Voltage Events in Hydrogen Arcs within Electric Arc Furnaces
This study highlights the potential utilization of hydrogen gas in electric arc furnaces for achieving cleaner and more sustainable steel production. The application of hydrogen offers a promising path for reducing carbon emissions, enhancing energy efficiency, and advancing the concept of “green steel”. This study employs a 2D axisymmetric induction-based model to simulate an electric arc under atmospheric pressure conditions. We conducted numerical simulations to compare compressible and incompressible models of an electric arc. The impact of compressibility on hydrogen arc characteristics such as arc velocity, temperature distribution, and voltage drop were investigated. Additionally, different applied current arcs were simulated using the compressible model. When compared to an incompressible arc, the compressible arc exhibits a higher voltage drop. This higher voltage drop is associated with lower temperatures and lower arc velocity. A rise in applied current results in an upward trend in the voltage drop and an increase in the arc radius. In addition, the increased applied current increases the probability of voltage fluctuations. The voltage fluctuations tend to become more extreme and exert more stress on the control circuit. This has an impact on emerging electric arc technologies, particularly those involving the use of hydrogen. These fluctuations affect arc stability, heat output, and the overall quality of processes. Thus, the precise prediction of voltage and the ability to stabilize the operation is critical for the successful implementation of new hydrogen technologies.