Irina Golubeva
Research Subjects
Irina Golubeva has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Yuriy Prokopenko
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
17 shared publications - Victor Kazmirenko
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
14 shared publications - Yuriy Poplavko
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
9 shared publications - Artem Serhiyovych Chernov
Національний технічний університет України «Київський політехнічний інститут імені Ігоря Сікорського
5 shared publications D. Smigin
National Technical University of Ukraine, 37, Peremogi Ave., Kiev, 03056, Ukraine
2 shared publicationsKostiantyn Savin
Department of Physical and Biomedical Electronics, National Technical University of Ukraine “KPI”, Kyiv, Ukraine
2 shared publications
Latest Publications
- 10 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 58, 155-159
Micromechanically Tunable Slotline as Part of the Filter Based on the Coplanar Waveguide with Defected Ground Structure
A new equivalent model of the defected ground structure for the CPW based filter is presented. The defected ground structure is considered as a short-ended slotline stubbed in the ground electrodes of the CPW line. Calculation of the filter's S-parameters could be performed by using the equivalent parameters of the line, such as effective dielectric permittivity and characteristic impedance. Both effective dielectric permittivity and characteristic impedance are obtained by using 2D finite element method applied to the cross-section of the line. Two ways for tuning slotline equivalent parameters are proposed. The simulation results of the proposed equivalent model are in good agreement with the 3D simulations. Such a method could be applied for the structures with various geometries and electro-physical parameters.
- 10 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 58, 155-159
Micromechanically Tunable Slotline as Part of the Filter Based on the Coplanar Waveguide with Defected Ground Structure
A new equivalent model of the defected ground structure for the CPW based filter is presented. The defected ground structure is considered as a short-ended slotline stubbed in the ground electrodes of the CPW line. Calculation of the filter's S-parameters could be performed by using the equivalent parameters of the line, such as effective dielectric permittivity and characteristic impedance. Both effective dielectric permittivity and characteristic impedance are obtained by using 2D finite element method applied to the cross-section of the line. Two ways for tuning slotline equivalent parameters are proposed. The simulation results of the proposed equivalent model are in good agreement with the 3D simulations. Such a method could be applied for the structures with various geometries and electro-physical parameters.
- 26 June 2020
- Published by Allerton Press in Radioelectronics and Communications Systems
- Vol. 63 (6) , 281-288
Complex Effective Dielectric Permittivity and Characteristic Impedance of Tunable Coplanar Line
An analysis of complex dielectric permittivity and characteristic impedance of micromechanically tunable coplanar line is presented. The coplanar line para
- 26 June 2020
- Published by Allerton Press in Radioelectronics and Communications Systems
- Vol. 63 (6) , 281-288
Complex Effective Dielectric Permittivity and Characteristic Impedance of Tunable Coplanar Line
An analysis of complex dielectric permittivity and characteristic impedance of micromechanically tunable coplanar line is presented. The coplanar line para
- 21 June 2020
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Известия высших учебных заведений. Радиоэлектроника
- Vol. 63 (6) , 331-342
Комплексная диэлектрическая проницаемость и характеристическое сопротивление перестраиваемой копланарной линии
Комплексная диэлектрическая проницаемость и характеристическое сопротивление перестраиваемой копланарной линии
- 21 June 2020
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Известия высших учебных заведений. Радиоэлектроника
- Vol. 63 (6) , 331-342
Комплексная диэлектрическая проницаемость и характеристическое сопротивление перестраиваемой копланарной линии
Комплексная диэлектрическая проницаемость и характеристическое сопротивление перестраиваемой копланарной линии
- Open Access
- 31 October 2019
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Microsystems, Electronics and Acoustics
- Vol. 24 (5) , 6-17
One-Dimensional Non-Uniform Dielectric Structure as Tunable Resonator
Одновимірна неоднорідна діелектрична структура, як перелаштовуваний резонатор
- 31 October 2019
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Microsystems, Electronics and Acoustics
- Vol. 24 (5) , 6-17
Open AccessOne-Dimensional Non-Uniform Dielectric Structure as Tunable Resonator
Одновимірна неоднорідна діелектрична структура, як перелаштовуваний резонатор
- Open Access
- 28 December 2018
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Microsystems, Electronics and Acoustics
- Vol. 23 (6) , 13-21
Tunable Coplanar Waveguide
Перелаштовувана копланарна лінія
- 28 December 2018
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Microsystems, Electronics and Acoustics
- Vol. 23 (6) , 13-21
Open AccessTunable Coplanar Waveguide
Перелаштовувана копланарна лінія
- 1 February 2018
- Published by Allerton Press in Radioelectronics and Communications Systems
- Vol. 61 (2) , 72-79
Complex Effective Dielectric Permittivity of Micromechanically Tunable Microstrip Lines
It is considered an influence of physical-topological parameters of controlled microstrip lines where characteristics modification is achieved by signal electrode movement over the substrate on...
- 1 February 2018
- Published by Allerton Press in Radioelectronics and Communications Systems
- Vol. 61 (2) , 72-79
Complex Effective Dielectric Permittivity of Micromechanically Tunable Microstrip Lines
It is considered an influence of physical-topological parameters of controlled microstrip lines where characteristics modification is achieved by signal electrode movement over the substrate on...
- 1 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 124-127
Tunability limits of the microstrip line with electromechanical control
The paper presents study of the tunable microstrip line with electromechanical control. The study derives dependencies of the effective permittivity and insertion loss on combination of substrate material properties and device dimensions. Asymptotic boundaries for effective permittivity and loss are derived.
- 1 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 124-127
Tunability limits of the microstrip line with electromechanical control
The paper presents study of the tunable microstrip line with electromechanical control. The study derives dependencies of the effective permittivity and insertion loss on combination of substrate material properties and device dimensions. Asymptotic boundaries for effective permittivity and loss are derived.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 520-522
A novel concept for the tunable cavity combline resonator
This paper presents a novel design of the cavity combline resonator. The resonator shows an extremely high sensitivity to the air gap thickness and high-Q performance. The design is well suited for electromechanical tuning. The results of the finite integration technique simulations are discussed. The influence of the resonator dimensions on the frequency tuning efficiency and the Q factor are presented.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 520-522
A novel concept for the tunable cavity combline resonator
This paper presents a novel design of the cavity combline resonator. The resonator shows an extremely high sensitivity to the air gap thickness and high-Q performance. The design is well suited for electromechanical tuning. The results of the finite integration technique simulations are discussed. The influence of the resonator dimensions on the frequency tuning efficiency and the Q factor are presented.
- 1 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Calculation of quality factor of tunable shielded cylindrical metal-dielectric resonator using mode matching technique
The paper discusses quality factor of shielded cylindrical metal-dielectric resonator tuned by means of variable air gap between resonator's base and shield. Mode matching technique was used to estimate resonator's quality factor taking into account dielectric and metal losses. It was shown that metal and dielectric losses decrease in case of the air gap inclusion.
- 1 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Calculation of quality factor of tunable shielded cylindrical metal-dielectric resonator using mode matching technique
The paper discusses quality factor of shielded cylindrical metal-dielectric resonator tuned by means of variable air gap between resonator's base and shield. Mode matching technique was used to estimate resonator's quality factor taking into account dielectric and metal losses. It was shown that metal and dielectric losses decrease in case of the air gap inclusion.
- 1 April 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 97-100
Loss in tunable microstrip lines
Electromagnetic energy loss in the micro-mechanically tunable microstrip line is studied including dielectric loss in substrate's medium and ohmic loss in metal electrodes. When total loss in the device is relatively small, loss mechanisms contribute additively, so complex effective permittivity can be used to account both phenomena. This simplifies analysis and design of tunable microstrip lines. It is shown that with micro-mechanical tuning both dielectric and metal loss decrease comparing to those of conventional line.
- 1 April 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 97-100
Loss in tunable microstrip lines
Electromagnetic energy loss in the micro-mechanically tunable microstrip line is studied including dielectric loss in substrate's medium and ohmic loss in metal electrodes. When total loss in the device is relatively small, loss mechanisms contribute additively, so complex effective permittivity can be used to account both phenomena. This simplifies analysis and design of tunable microstrip lines. It is shown that with micro-mechanical tuning both dielectric and metal loss decrease comparing to those of conventional line.