Aparecido Junior de Menezes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aparecido Junior de Menezes has a total of 106 co-authors. Here are the top co-authors by number of shared publications:
- Lucas Repecka Alves
Universidade Federal de São Carlos
14 shared publications - Giovanni Miraveti Carriello
Federal University of Sao Carlos
11 shared publications - Henrique Solowej Medeiros Lopes
Federal University of São Carlos (UFSCar), 110 João Leme dos Santos Rd., Sorocaba, São Paulo 18052-780, Brazil
10 shared publications - Guilherme Manassés Pegoraro
Universidade Federal de São Carlos, Brasil
8 shared publications - Samir Leite Mathias
Research Group of Polymers From Renewable Sources, Department of Physics, Chemistry and Mathematics Federal University of São Carlos Sorocaba Brazil
7 shared publications - Giovanni Pimenta Mambrini
Graduate Program in Materials Science Federal University of Sao Carlos Sorocaba São Paulo Brazil
6 shared publications
Latest Publications
- Open Access
- 8 November 2026
- Published by Wiley in Hydrological Processes
- Vol. 40 (11) , e70775
Physical Structure and Dynamic Wettability Shape Bark Water Uptake and Storage in Amazonian Trees
Tree bark is a hydrologically active interface that can retain water, regulate the establishment of surface flow, and influence rainfall partitioning along stems. However, the physical, chemical, and surface traits associated with bark water uptake and storage remain poorly integrated, particularly for Amazonian trees. We investigated bark from nine Amazonian tree species representing contrasting surface types. Dynamic apparent contact angle was measured on naturally exposed and previously unwetted bark surfaces, followed by quantification of bark thickness, maximum gravimetric water absorbability, areal water‐storage capacity, water‐uptake kinetics over 96 h, and chemical composition. Associations among nine tree‐level bark observations were evaluated using Spearman rank correlations. Initial apparent contact angle and its reduction during the first 30 s varied markedly and did not follow a common pattern, indicating that initial droplet configuration and early dynamic wettability captured different surface responses. Bark thickness was strongly associated with areal water‐storage capacity. Maximum gravimetric absorbability and uptake kinetics also showed contrasting combinations across the bark observations: the time required to reach 50% saturation ( T 50 ) was negatively associated with both maximum gravimetric absorbability and early contact‐angle reduction, whereas initial apparent contact angle showed little relationship with T 50 . The time required to reach 90% saturation ( T 90 ) was weakly associated with the principal storage and wettability traits, indicating that early reservoir filling and the approach to saturation followed different patterns. Chemical composition was selectively associated with surface wettability: acid‐insoluble lignin was negatively related to initial apparent contact angle, whereas hemicellulose was negatively related to early contact‐angle reduction. Chemical traits showed little correspondence with maximum liquid‐water storage. The observed associations suggest that bark hydrological functioning involves complementary dimensions, with physical structure related to areal storage capacity, dynamic wettability associated with early uptake kinetics, and bulk chemical composition related to selected surface‐wetting responses. These findings support a trait‐based interpretation of bark as a dynamic component of canopy water partitioning.
- 8 November 2026
- Published by Wiley in Hydrological Processes
- Vol. 40 (11) , e70775
Open AccessPhysical Structure and Dynamic Wettability Shape Bark Water Uptake and Storage in Amazonian Trees
Tree bark is a hydrologically active interface that can retain water, regulate the establishment of surface flow, and influence rainfall partitioning along stems. However, the physical, chemical, and surface traits associated with bark water uptake and storage remain poorly integrated, particularly for Amazonian trees. We investigated bark from nine Amazonian tree species representing contrasting surface types. Dynamic apparent contact angle was measured on naturally exposed and previously unwetted bark surfaces, followed by quantification of bark thickness, maximum gravimetric water absorbability, areal water‐storage capacity, water‐uptake kinetics over 96 h, and chemical composition. Associations among nine tree‐level bark observations were evaluated using Spearman rank correlations. Initial apparent contact angle and its reduction during the first 30 s varied markedly and did not follow a common pattern, indicating that initial droplet configuration and early dynamic wettability captured different surface responses. Bark thickness was strongly associated with areal water‐storage capacity. Maximum gravimetric absorbability and uptake kinetics also showed contrasting combinations across the bark observations: the time required to reach 50% saturation ( T 50 ) was negatively associated with both maximum gravimetric absorbability and early contact‐angle reduction, whereas initial apparent contact angle showed little relationship with T 50 . The time required to reach 90% saturation ( T 90 ) was weakly associated with the principal storage and wettability traits, indicating that early reservoir filling and the approach to saturation followed different patterns. Chemical composition was selectively associated with surface wettability: acid‐insoluble lignin was negatively related to initial apparent contact angle, whereas hemicellulose was negatively related to early contact‐angle reduction. Chemical traits showed little correspondence with maximum liquid‐water storage. The observed associations suggest that bark hydrological functioning involves complementary dimensions, with physical structure related to areal storage capacity, dynamic wettability associated with early uptake kinetics, and bulk chemical composition related to selected surface‐wetting responses. These findings support a trait‐based interpretation of bark as a dynamic component of canopy water partitioning.
- Open Access
- 3 November 2026
- Published by Elsevier in Sustainable Chemistry and Pharmacy
- Vol. 54
Chemical functionalization of cellulose nanofibrils with 2-chloroethylamine hydrochloride
- 3 November 2026
- Published by Elsevier in Sustainable Chemistry and Pharmacy
- Vol. 54
Open AccessChemical functionalization of cellulose nanofibrils with 2-chloroethylamine hydrochloride
- Open Access
- 10 September 2026
- Published by Wiley in Journal of Polymer Science
Leucaena Oil Functionalized With Osmium Tetroxide as a Precursor for Polyol‐Based Polyurethane
The widespread use of polyurethane (PU) in insulation, packaging, and furniture remains heavily dependent on petrochemical polyols, raising sustainability concerns. Renewable, biodegradable, and high‐performance bio‐based polyols therefore remain a strategic research focus. Here, Leucaena leucocephala seed oil (a nonedible, fast‐growing tropical biomass) is extracted by Soxhlet and functionalized via osmylation to produce a hydroxylated polyol suitable for polyurethane synthesis. An osmium tetroxide–pyridine system enables syn‐addition of vicinal diols to unsaturated fatty‐acid chains, increasing hydroxyl functionality Fourier transform infrared spectroscopy, Raman spectroscopy, ultraviolet–visible spectroscopy, differential scanning calorimetry e thermogravimetric/derivative thermogravimetric analysis data support hydroxylation while indicating preservation of the triglyceride backbone. The resulting polyol shows a hydroxyl number of 160–175 mg KOH g −1 , increased viscosity, and higher acidity than the crude oil, consistent with OH incorporation. Thermal analysis reveals two main degradation events ( T max ≈ 391°C–397°C), with residues below 5%. Flexible, open‐cell PUs are produced via the one‐shot method using triethanolamine and 1,4‐diazabicyclo[2.2.2]octane catalysts, showing C/O/N signals and predominantly amorphous X‐ray diffraction profiles. Overall, Leucaena oil emerges as a renewable feedstock for polyol and polyurethane production, supporting reduced petrochemical dependence through biomass valorization.
- 10 September 2026
- Published by Wiley in Journal of Polymer Science
Open AccessLeucaena Oil Functionalized With Osmium Tetroxide as a Precursor for Polyol‐Based Polyurethane
The widespread use of polyurethane (PU) in insulation, packaging, and furniture remains heavily dependent on petrochemical polyols, raising sustainability concerns. Renewable, biodegradable, and high‐performance bio‐based polyols therefore remain a strategic research focus. Here, Leucaena leucocephala seed oil (a nonedible, fast‐growing tropical biomass) is extracted by Soxhlet and functionalized via osmylation to produce a hydroxylated polyol suitable for polyurethane synthesis. An osmium tetroxide–pyridine system enables syn‐addition of vicinal diols to unsaturated fatty‐acid chains, increasing hydroxyl functionality Fourier transform infrared spectroscopy, Raman spectroscopy, ultraviolet–visible spectroscopy, differential scanning calorimetry e thermogravimetric/derivative thermogravimetric analysis data support hydroxylation while indicating preservation of the triglyceride backbone. The resulting polyol shows a hydroxyl number of 160–175 mg KOH g −1 , increased viscosity, and higher acidity than the crude oil, consistent with OH incorporation. Thermal analysis reveals two main degradation events ( T max ≈ 391°C–397°C), with residues below 5%. Flexible, open‐cell PUs are produced via the one‐shot method using triethanolamine and 1,4‐diazabicyclo[2.2.2]octane catalysts, showing C/O/N signals and predominantly amorphous X‐ray diffraction profiles. Overall, Leucaena oil emerges as a renewable feedstock for polyol and polyurethane production, supporting reduced petrochemical dependence through biomass valorization.
- Open Access
- 22 June 2026
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 372, 153148
Mechanical performance enhancement of cassava starch and açaí residue films through optimized hydroxypropylation reaction
- 22 June 2026
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 372, 153148
Open AccessMechanical performance enhancement of cassava starch and açaí residue films through optimized hydroxypropylation reaction
- Open Access
- 1 June 2026
- Published by Ion Creanga State Pedagogical University in Acta Et Commentationes Exact and Natural Sciences
- Vol. 21 (1) , 62-68
Optimization of holocellulose extraction from spent coffee grounds using factorial design
Spent coffee grounds (SCG) represent a substantial environmental challenge due to the massive generation of solid waste and its high organic load. However, SCG is a promising source of lignocellulosic biomass for the production of high-value biopolymers. This study aimed to optimize the extraction of holocellulose from SCG via oxidative bleaching using sodium hypochlorite (NaOCl), employing a 2³ factorial design with a central point. The effects of NaOCl concentration (1.0--2.5%), reaction time (15--45 min), and temperature (25--55 °C) on the extraction yield were evaluated. Statistical analysis revealed that temperature was the most significant variable, accounting for approximately 52% of the yield variation, followed by NaOCl concentration (~37%). High temperatures and concentrations led to excessive oxidative degradation and hydrolysis of the polysaccharide chains, drastically reducing yields to below 20%. Conversely, mild conditions resulted in insufficient delignification. The experimental results indicated that the central point conditions (1.75% NaOCl at 40 °C for 30 min) offered the optimal balance, providing a yield of approximately 38% with adequate brightness and reduced degradation. These findings demonstrate the feasibility of using statistical design to obtain holocellulose from SCG for future applications in biocomposites and packaging.
- 1 June 2026
- Published by Ion Creanga State Pedagogical University in Acta Et Commentationes Exact and Natural Sciences
- Vol. 21 (1) , 62-68
Open AccessOptimization of holocellulose extraction from spent coffee grounds using factorial design
Spent coffee grounds (SCG) represent a substantial environmental challenge due to the massive generation of solid waste and its high organic load. However, SCG is a promising source of lignocellulosic biomass for the production of high-value biopolymers. This study aimed to optimize the extraction of holocellulose from SCG via oxidative bleaching using sodium hypochlorite (NaOCl), employing a 2³ factorial design with a central point. The effects of NaOCl concentration (1.0--2.5%), reaction time (15--45 min), and temperature (25--55 °C) on the extraction yield were evaluated. Statistical analysis revealed that temperature was the most significant variable, accounting for approximately 52% of the yield variation, followed by NaOCl concentration (~37%). High temperatures and concentrations led to excessive oxidative degradation and hydrolysis of the polysaccharide chains, drastically reducing yields to below 20%. Conversely, mild conditions resulted in insufficient delignification. The experimental results indicated that the central point conditions (1.75% NaOCl at 40 °C for 30 min) offered the optimal balance, providing a yield of approximately 38% with adequate brightness and reduced degradation. These findings demonstrate the feasibility of using statistical design to obtain holocellulose from SCG for future applications in biocomposites and packaging.
- Open Access
- 1 October 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (40) , 46822-46831
High-Elongation Starch Films by Hydroxypropylation Reaction with Low Glycerol Content
Hydroxypropylation is habitually used to modify starch by grafting bulky side groups onto its hydroxyls, significantly altering its structural, mechanical, and morphological properties. The hydroxypropylation reaction carried out in this study induced the gelatinization of starch, a phenomenon that is rarely observed in the literature due to the reaction conditions. This distinctive outcome is highly promising, as it enables the production of films with a reduced plasticizer content, offering a significant advantage over conventional methods. In this work, the identified presence of poly-(propylene oxide) (PPO) was investigated to enhance the flexibility of hydroxypropylated starch films, increasing elongation at break from 6% to 34% with only 7.5% glycerol (by weight of starch). PPO also accelerated retrogradation kinetics, attributed to its lubricating effect on starch molecules, and altered the surface energy, resulting in an increased polarity at lower molar ratios. These modifications led to films with reduced brittleness and improved mechanical performance. Scanning electron microscopy revealed a transition from brittle surfaces in native starch films to smoother, more ductile surfaces in modified films. This study demonstrates the effectiveness of PPO as a plasticizer, reducing the need for additional plasticizers and energy-intensive processing. These findings highlight the potential of hydroxypropylated starch films for sustainable packaging applications, advancing the development of eco-friendly materials with enhanced properties.
- 1 October 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (40) , 46822-46831
Open AccessHigh-Elongation Starch Films by Hydroxypropylation Reaction with Low Glycerol Content
Hydroxypropylation is habitually used to modify starch by grafting bulky side groups onto its hydroxyls, significantly altering its structural, mechanical, and morphological properties. The hydroxypropylation reaction carried out in this study induced the gelatinization of starch, a phenomenon that is rarely observed in the literature due to the reaction conditions. This distinctive outcome is highly promising, as it enables the production of films with a reduced plasticizer content, offering a significant advantage over conventional methods. In this work, the identified presence of poly-(propylene oxide) (PPO) was investigated to enhance the flexibility of hydroxypropylated starch films, increasing elongation at break from 6% to 34% with only 7.5% glycerol (by weight of starch). PPO also accelerated retrogradation kinetics, attributed to its lubricating effect on starch molecules, and altered the surface energy, resulting in an increased polarity at lower molar ratios. These modifications led to films with reduced brittleness and improved mechanical performance. Scanning electron microscopy revealed a transition from brittle surfaces in native starch films to smoother, more ductile surfaces in modified films. This study demonstrates the effectiveness of PPO as a plasticizer, reducing the need for additional plasticizers and energy-intensive processing. These findings highlight the potential of hydroxypropylated starch films for sustainable packaging applications, advancing the development of eco-friendly materials with enhanced properties.
- 16 September 2025
- Published by Elsevier in Science of The Total Environment
- Vol. 1000, 180452
Tree bark actively mediates atmospheric water storage in tropical cloud forests
- 16 September 2025
- Published by Elsevier in Science of The Total Environment
- Vol. 1000, 180452
Tree bark actively mediates atmospheric water storage in tropical cloud forests
- Open Access
- 1 August 2025
- Published by Seven Events in LUMEN ET VIRTUS
- Vol. 16 (51) , e7691
BALANCING FLEXIBILITY AND STRENGTH OF HYDROXYPROPYLATED STARCH/CELLULOSE NANOFIBRILS BIOCOMPOSITES
This study investigates the thermal-mechanical properties of hydroxypropylated starch (HPS) as a plasticizer for conventional thermoplastic starch (TPS) films, reinforced with cellulose nanofibrils (CNF). A previous study showed that hydroxypropylation of starch led to in-situ poly(propylene oxide) (PPO) formation, inducing gelatinization and yielding TPS with significant plasticizing effect. To address this, blending native cassava starch with HPS and incorporating CNF, as well as hydroxypropylated CNF (mCNF), was explored as a sustainable reinforcement strategy. Films were prepared by casting, and their properties were evaluated using tensile strength tests, Fourier-transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TG). Results indicate that the incorporation of unmodified CNF significantly increased the tensile strength of HPS/TPS films, demonstrating its effective reinforcing capability. Conversely, adding mCNF led to a reduction in tensile strength, suggesting that the chemical modification of CNF may hinder its reinforcing efficiency due to altered interactions with the starch matrix. FTIR confirmed molecular interactions, while DSC and TG provided insights into thermal transitions and stability. This research emphasizes the potential of combining HPS, native starch, and CNF to create sustainable, high-performance starch-based biocomposites with reduced synthetic plasticizer content, offering a promising approach for diverse applications.
- 1 August 2025
- Published by Seven Events in LUMEN ET VIRTUS
- Vol. 16 (51) , e7691
Open AccessBALANCING FLEXIBILITY AND STRENGTH OF HYDROXYPROPYLATED STARCH/CELLULOSE NANOFIBRILS BIOCOMPOSITES
This study investigates the thermal-mechanical properties of hydroxypropylated starch (HPS) as a plasticizer for conventional thermoplastic starch (TPS) films, reinforced with cellulose nanofibrils (CNF). A previous study showed that hydroxypropylation of starch led to in-situ poly(propylene oxide) (PPO) formation, inducing gelatinization and yielding TPS with significant plasticizing effect. To address this, blending native cassava starch with HPS and incorporating CNF, as well as hydroxypropylated CNF (mCNF), was explored as a sustainable reinforcement strategy. Films were prepared by casting, and their properties were evaluated using tensile strength tests, Fourier-transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TG). Results indicate that the incorporation of unmodified CNF significantly increased the tensile strength of HPS/TPS films, demonstrating its effective reinforcing capability. Conversely, adding mCNF led to a reduction in tensile strength, suggesting that the chemical modification of CNF may hinder its reinforcing efficiency due to altered interactions with the starch matrix. FTIR confirmed molecular interactions, while DSC and TG provided insights into thermal transitions and stability. This research emphasizes the potential of combining HPS, native starch, and CNF to create sustainable, high-performance starch-based biocomposites with reduced synthetic plasticizer content, offering a promising approach for diverse applications.
- Open Access
- 9 May 2025
- Published by Disciplinarum Scientia: Serie Ciencias Naturais e Tecnologicas in Disciplinarum Scientia - Ciências Naturais e Tecnológicas
- Vol. 26 (2) , 171-180
Effect of chain extender on post-consumer polyethylene terephtalate (PET): a comparison with virgin pet
This study aimed to investigate the impact of a chain extender on the thermal properties of recycled polyethylene terephthalate (PET) compared to virgin PET. FTIR analysis revealed no changes in the chemical structure of PET after the addition of the extender. DSC analysis results showed that post-consumer PET with the extender exhibited a glass transition temperature (Tg) similar to that of virgin PET, indicating possible crosslinking. All PET materials displayed cold crystallization behavior, with differences observed between virgin and recycled PET. It is concluded that the chain extender modified the thermal properties of recycled PET, suggesting that it may influence the quality of recycled materials.
- 9 May 2025
- Published by Disciplinarum Scientia: Serie Ciencias Naturais e Tecnologicas in Disciplinarum Scientia - Ciências Naturais e Tecnológicas
- Vol. 26 (2) , 171-180
Open AccessEffect of chain extender on post-consumer polyethylene terephtalate (PET): a comparison with virgin pet
This study aimed to investigate the impact of a chain extender on the thermal properties of recycled polyethylene terephthalate (PET) compared to virgin PET. FTIR analysis revealed no changes in the chemical structure of PET after the addition of the extender. DSC analysis results showed that post-consumer PET with the extender exhibited a glass transition temperature (Tg) similar to that of virgin PET, indicating possible crosslinking. All PET materials displayed cold crystallization behavior, with differences observed between virgin and recycled PET. It is concluded that the chain extender modified the thermal properties of recycled PET, suggesting that it may influence the quality of recycled materials.
- Open Access
- 20 March 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (12) , 12543-12552
Gelatinized Cassava Starch Obtained via Low Molar Ratio Hydroxypropylation Reaction
Hydroxypropylated starch was successfully synthesized, aiming to address the limitations of native starch, such as poor mechanical properties and water sensitivity, which hinder its application in biodegradable polymers. The modification process, conducted at 115-135 °C with propylene oxide (PO) molar ratios of 0.4-0.8 [PO molecule per OH of starch], effectively disrupted the native starch structure. FTIR and 13C NMR confirmed methyl group incorporation, with lower temperatures and higher PO ratios yielding greater modification. SEM and XRD analyses demonstrated complete gelatinization; although some short-range order structures are present, long-range structures were eliminated, while DSC confirmed the absence of gelatinization peaks. TGA revealed the integration of lower molecular weight molecules, suggesting PPO homopolymerization within the starch granules. These structural transformations enhance the feasibility of producing hydroxypropylated starch films with reduced plasticizer content and energy requirements, offering a novel approach to improving starch-based materials for biodegradable applications.
- 20 March 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (12) , 12543-12552
Open AccessGelatinized Cassava Starch Obtained via Low Molar Ratio Hydroxypropylation Reaction
Hydroxypropylated starch was successfully synthesized, aiming to address the limitations of native starch, such as poor mechanical properties and water sensitivity, which hinder its application in biodegradable polymers. The modification process, conducted at 115-135 °C with propylene oxide (PO) molar ratios of 0.4-0.8 [PO molecule per OH of starch], effectively disrupted the native starch structure. FTIR and 13C NMR confirmed methyl group incorporation, with lower temperatures and higher PO ratios yielding greater modification. SEM and XRD analyses demonstrated complete gelatinization; although some short-range order structures are present, long-range structures were eliminated, while DSC confirmed the absence of gelatinization peaks. TGA revealed the integration of lower molecular weight molecules, suggesting PPO homopolymerization within the starch granules. These structural transformations enhance the feasibility of producing hydroxypropylated starch films with reduced plasticizer content and energy requirements, offering a novel approach to improving starch-based materials for biodegradable applications.