Rubens de Andrade
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rubens de Andrade has a total of 140 co-authors. Here are the top co-authors by number of shared publications:
- Guilherme Gonçalves Sotelo
Universidade Federal Fluminense (UFF), Niteri, Brazil
39 shared publications - Richard Magdalena Stephan
Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, Brazil
22 shared publications - Felipe Sass
Universidade Federal Fluminense, Niteri, Brazil
17 shared publications - Alexander Polasek
Electric Power Research Center, Brazil
14 shared publications - Bárbara Maria Oliveira Santos
Rio de Janeiro State University, Rio de Janeiro, Brazil
12 shared publications - Wescley Tiago Batista de Sousa
Institute for Technical Physics, Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen, Germany
11 shared publications
Latest Publications
- Open Access
- 27 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
J-A-$\phi$ Formulation Applied to Simulations of Linear Magnetic Bearings
The J-A-$\phi$ formulation has been proposed lately. Its objective is to reduce the computational load of finite element electromagnetic simulations of superconducting devices. This formulation is the combination of the J-A approach, in which the magnetic vector potential, A, and the current density, J, are directly computed; and the use of magnetic scalar potential, $\phi$, in the current-free domains, a technique usually adopted in the H-$\phi$ formulation. This work introduces how to couple the A and $\phi$ fields when one of them is defined in a moving mesh. For proving the proposed methodology, this work applies the J-A-$\phi$ formulation to simulations of superconducting magnetic bearings. Combined with a 2D planar approximation, the formulation is applied to the entire system, including the magnetic guideway and the superconducting domains, with linear vertical and lateral movements. The superconducting domains of choice comprise bulks and stacks of 2G tapes. Levitation and guidance forces are analyzed as results and validated against experimental data when available. This application allows for a deep observation of how the J-A-$\phi$ formulation works alongside finite element mesh movement, which is of extreme importance for designs of devices such as magnetic bearings and electric machinery.
- 27 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Open AccessJ-A-$\phi$ Formulation Applied to Simulations of Linear Magnetic Bearings
The J-A-$\phi$ formulation has been proposed lately. Its objective is to reduce the computational load of finite element electromagnetic simulations of superconducting devices. This formulation is the combination of the J-A approach, in which the magnetic vector potential, A, and the current density, J, are directly computed; and the use of magnetic scalar potential, $\phi$, in the current-free domains, a technique usually adopted in the H-$\phi$ formulation. This work introduces how to couple the A and $\phi$ fields when one of them is defined in a moving mesh. For proving the proposed methodology, this work applies the J-A-$\phi$ formulation to simulations of superconducting magnetic bearings. Combined with a 2D planar approximation, the formulation is applied to the entire system, including the magnetic guideway and the superconducting domains, with linear vertical and lateral movements. The superconducting domains of choice comprise bulks and stacks of 2G tapes. Levitation and guidance forces are analyzed as results and validated against experimental data when available. This application allows for a deep observation of how the J-A-$\phi$ formulation works alongside finite element mesh movement, which is of extreme importance for designs of devices such as magnetic bearings and electric machinery.
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Pulsed Magnetization on Jointless Loops Coil Using Multi-Toroidal Auxiliary Winding
Jointless persistent current coils, known as the crossed loops, have been developed and studied by our group since 2018 and could be an interesting solution for challenges concerning current leads for HTS field coils in electric machine applications. To trap flux in such coils, pulsed field magnetization (PFM) through the armature coils is often employed. In this work, a different PFM is proposed, by taking advantage of the jointless loops geometry. This approach uses a low-current secondary winding magnetically coupled to the coil heads, wound in a toroidal shape, forcing the pulsed magnetic field around the HTS tapes and inducing persistent currents. The main advantage of this idea is that such auxiliary winding could be used as a flux pump for its main coils without the need to reroute the stator source for a re-magnetization process. A prototype of the proposed application is presented in this work. It was verified using finite element simulations then built and tested as a proof of concept. Its behavior is observed and a special attention is given to how the coupling of multiple loops affect the global persistent current of a coil, due to the dependence of the critical current to the magnetic field. The data show the feasibility of the proposed idea and opens another path for improving the HTS crossed-loops machine topology.
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Pulsed Magnetization on Jointless Loops Coil Using Multi-Toroidal Auxiliary Winding
Jointless persistent current coils, known as the crossed loops, have been developed and studied by our group since 2018 and could be an interesting solution for challenges concerning current leads for HTS field coils in electric machine applications. To trap flux in such coils, pulsed field magnetization (PFM) through the armature coils is often employed. In this work, a different PFM is proposed, by taking advantage of the jointless loops geometry. This approach uses a low-current secondary winding magnetically coupled to the coil heads, wound in a toroidal shape, forcing the pulsed magnetic field around the HTS tapes and inducing persistent currents. The main advantage of this idea is that such auxiliary winding could be used as a flux pump for its main coils without the need to reroute the stator source for a re-magnetization process. A prototype of the proposed application is presented in this work. It was verified using finite element simulations then built and tested as a proof of concept. Its behavior is observed and a special attention is given to how the coupling of multiple loops affect the global persistent current of a coil, due to the dependence of the critical current to the magnetic field. The data show the feasibility of the proposed idea and opens another path for improving the HTS crossed-loops machine topology.
- 24 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
Simulation of Pulsed-Magnetization of HTS Jointless Loops With J-A Formulation With Circuit Coupling and Thermal Modeling
The J-A formulation has been investigated as an easy and fast way to model superconducting systems in finite-element software. It is based on the common A-formulation, but two equations are applied. One to compute the magnetic field, which is the A-formulation equation, and one to compute the current density directly. By doing this, it is possible to use resistivity instead of conductivity to represent the superconductor, thereby eliminating a circular variable problem. This formulation has been investigated in both 2D and 3D, for thin-film approximations and homogenization methods, and the method to couple it with electric circuits has been recently proposed. This work explores it further by using the J-A formulation with circuit coupling and electro-thermal model to compute the thermal behavior of superconducting systems. It is applied to the pulsed-magnetization of HTS jointless loops, a system which has been investigated experimentally in previous works. The system is composed of a transformer with a common copper primary coil and the HTS jointless loop as secondary coil. The HTS loop placed in a nitrogen bath, modeled by the electro-thermal analogy method. An electric circuit is used to model the current continuity of the HTS loop. The J-A formulation computes the current density and the magnetic field. The pulses are investigated with a fixed pulse length and several pulse magnitudes, each in a different simulation. The induced persistent current is compared for all magnitudes, as well as the temperature rise for all layers of the HTS tape.
- 24 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
Simulation of Pulsed-Magnetization of HTS Jointless Loops With J-A Formulation With Circuit Coupling and Thermal Modeling
The J-A formulation has been investigated as an easy and fast way to model superconducting systems in finite-element software. It is based on the common A-formulation, but two equations are applied. One to compute the magnetic field, which is the A-formulation equation, and one to compute the current density directly. By doing this, it is possible to use resistivity instead of conductivity to represent the superconductor, thereby eliminating a circular variable problem. This formulation has been investigated in both 2D and 3D, for thin-film approximations and homogenization methods, and the method to couple it with electric circuits has been recently proposed. This work explores it further by using the J-A formulation with circuit coupling and electro-thermal model to compute the thermal behavior of superconducting systems. It is applied to the pulsed-magnetization of HTS jointless loops, a system which has been investigated experimentally in previous works. The system is composed of a transformer with a common copper primary coil and the HTS jointless loop as secondary coil. The HTS loop placed in a nitrogen bath, modeled by the electro-thermal analogy method. An electric circuit is used to model the current continuity of the HTS loop. The J-A formulation computes the current density and the magnetic field. The pulses are investigated with a fixed pulse length and several pulse magnitudes, each in a different simulation. The induced persistent current is compared for all magnitudes, as well as the temperature rise for all layers of the HTS tape.
- 5 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (4) , 1-4
J-A Approach to Simulations of HTS Tapes: How to Couple With Electric Circuits
The J-A formulation or approach, is a set of differential equations that allow simulations of superconducting devices with A-formulation-based modeling without the need to use conductivity, which may cause numerical stability problems in finite element solvers. In this article, a method to couple the J-A approach to electric circuits is presented and discussed. A simple test case of a single tape connected to a circuit is used as a benchmark. Two strategies of physical representation of superconducting tapes are explored. The first, and the simplest, is the approximation of the tape as a thin-film, considering only the superconducting layer. The second strategy applies the thin-film approximation to the entire tape, in order to fully represent the magnetic field of the tape. The ac losses, current density and total current results of both strategies are directly compared with results obtained with the well-established T-A formulation. It is found that all results are totally compatible. The J-A approach is proving to be an interesting alternative if faster computational times are needed in 2-D simulations.
- 5 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (4) , 1-4
J-A Approach to Simulations of HTS Tapes: How to Couple With Electric Circuits
The J-A formulation or approach, is a set of differential equations that allow simulations of superconducting devices with A-formulation-based modeling without the need to use conductivity, which may cause numerical stability problems in finite element solvers. In this article, a method to couple the J-A approach to electric circuits is presented and discussed. A simple test case of a single tape connected to a circuit is used as a benchmark. Two strategies of physical representation of superconducting tapes are explored. The first, and the simplest, is the approximation of the tape as a thin-film, considering only the superconducting layer. The second strategy applies the thin-film approximation to the entire tape, in order to fully represent the magnetic field of the tape. The ac losses, current density and total current results of both strategies are directly compared with results obtained with the well-established T-A formulation. It is found that all results are totally compatible. The J-A approach is proving to be an interesting alternative if faster computational times are needed in 2-D simulations.
- 1 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
Vertical and Horizontal Force Measurements of a Double Crossed Loop
Superconducting coils made from REBCO coated conductors are widely researched for various applications. Amongst the many HTS coil designs in the literature, the double crossed loop (DCL) coils are an interesting possibility for trapped flux and induced current applications, such as magnetic bearings. The DCL coils were proposed, simulated, and tested in small-scale prototypes as proof of concept in previous works. Recent works dealt with the modeling challenges concerning the correct representation of the induced currents. The present study aims to investigate a larger scale magnetic bearing designed and built using DCL coils as a substitute for an existent and validated magnetic bearing made with HTS bulks. The proposed bearing is presented here, where the practical results from the previous study provided guidelines for a better design concerning levitation forces for the DCL coils. The bearing performance is measured via levitation force tests (vertical and lateral displacements) against the permanent magnet assembly from the original bearing. Such results are compared with the previous prototype and allow to verify the DCL coil bearing reliability.
- 1 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
Vertical and Horizontal Force Measurements of a Double Crossed Loop
Superconducting coils made from REBCO coated conductors are widely researched for various applications. Amongst the many HTS coil designs in the literature, the double crossed loop (DCL) coils are an interesting possibility for trapped flux and induced current applications, such as magnetic bearings. The DCL coils were proposed, simulated, and tested in small-scale prototypes as proof of concept in previous works. Recent works dealt with the modeling challenges concerning the correct representation of the induced currents. The present study aims to investigate a larger scale magnetic bearing designed and built using DCL coils as a substitute for an existent and validated magnetic bearing made with HTS bulks. The proposed bearing is presented here, where the practical results from the previous study provided guidelines for a better design concerning levitation forces for the DCL coils. The bearing performance is measured via levitation force tests (vertical and lateral displacements) against the permanent magnet assembly from the original bearing. Such results are compared with the previous prototype and allow to verify the DCL coil bearing reliability.
- 22 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
Use of the J-A Approach to Model Homogenized 2G Tape Stacks and HTS Bulks
This work explores an easy way to implement a current density focused formulation in commercial software, the J-A approach. The current density and magnetic vector potential are computed directly from the A-formulation, with only differential equations. The J-A has already been applied to simulate only one coated conductor, and the results were similar to the ones presented by the T-A formulation. The present work expands this idea to model bulks and stacks of coated conductors in 2D simulations. The J-A approach is used to compute the current density distribution and the levitation force of bulks and stacks of tapes acting as superconducting magnetic bearings to check the model's applicability. This model includes the complete representation of the magnetic guideway and a moving mesh representing movement between the superconducting region and the magnetic guideway. This approach provides a simple and fast way to investigate the major characteristics of superconducting devices that may be applied in their optimization. The simulated results have agreed with experimental data, which validates the J-A approach for the studied cases.
- 22 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
Use of the J-A Approach to Model Homogenized 2G Tape Stacks and HTS Bulks
This work explores an easy way to implement a current density focused formulation in commercial software, the J-A approach. The current density and magnetic vector potential are computed directly from the A-formulation, with only differential equations. The J-A has already been applied to simulate only one coated conductor, and the results were similar to the ones presented by the T-A formulation. The present work expands this idea to model bulks and stacks of coated conductors in 2D simulations. The J-A approach is used to compute the current density distribution and the levitation force of bulks and stacks of tapes acting as superconducting magnetic bearings to check the model's applicability. This model includes the complete representation of the magnetic guideway and a moving mesh representing movement between the superconducting region and the magnetic guideway. This approach provides a simple and fast way to investigate the major characteristics of superconducting devices that may be applied in their optimization. The simulated results have agreed with experimental data, which validates the J-A approach for the studied cases.
- Open Access
A Review of Technology Readiness Levels for Superconducting Electric Machinery
Superconducting electric machines (SEMs) have the potential to be commercially available in the coming years. This commercialization depends on the availability of high-temperature superconductors (HTS) produced on a large scale. HTSs have high current densities and low losses, making them the leading technology choice for future light and compact high-power-density superconducting rotating machines, with a particular niche for high torque at low frequency. The advantages of SEM in its fully superconducting design or hybrid configuration (conventional stator, superconducting rotor) inherit from the characteristics of the superconductor material. So, they can show greater efficiency at a higher power density and lighter frame than their conventional counterparts for an equivalent power rating. Applications like electric aircraft, naval propulsion, and wind turbines, among others, are likely to use SEMs if the rated power has to be increased beyond what is technically available with conventional technology. In this context, this paper reviews SEMs and their applications. However, it also aims to highlight the main the literature projects with a minimal Technology Readiness Level (TRL) larger than three. Due to the diversity of the superconductors’ characteristics and the variety of machines, the modes of operation of SEMs can be quite distinct from conventional machines. Taking into account such diversity, SEMs are presented and sorted out by their operational principles and the choice of superconducting material. Finally, the future perspectives of SEM are discussed.
Open AccessA Review of Technology Readiness Levels for Superconducting Electric Machinery
Superconducting electric machines (SEMs) have the potential to be commercially available in the coming years. This commercialization depends on the availability of high-temperature superconductors (HTS) produced on a large scale. HTSs have high current densities and low losses, making them the leading technology choice for future light and compact high-power-density superconducting rotating machines, with a particular niche for high torque at low frequency. The advantages of SEM in its fully superconducting design or hybrid configuration (conventional stator, superconducting rotor) inherit from the characteristics of the superconductor material. So, they can show greater efficiency at a higher power density and lighter frame than their conventional counterparts for an equivalent power rating. Applications like electric aircraft, naval propulsion, and wind turbines, among others, are likely to use SEMs if the rated power has to be increased beyond what is technically available with conventional technology. In this context, this paper reviews SEMs and their applications. However, it also aims to highlight the main the literature projects with a minimal Technology Readiness Level (TRL) larger than three. Due to the diversity of the superconductors’ characteristics and the variety of machines, the modes of operation of SEMs can be quite distinct from conventional machines. Taking into account such diversity, SEMs are presented and sorted out by their operational principles and the choice of superconducting material. Finally, the future perspectives of SEM are discussed.
- 22 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (8) , 1-6
Response of a Trapped Flux Superconducting Motor to Two Drive Methods
This work presents the starting of a trapped flux superconducting motor considering two drive methods: direct starting (using an ac power source) and soft starting (using a frequency inverter). These two methods present different characteristics that are expected to affect the behavior of the superconducting motor. For the direct starting, there is inrush current but no harmonics. On the contrary, for soft starting, there are harmonics but no inrush current. To understand the impacts of the starting current or the harmonics on the performance of superconducting motors, different tests were carried out on a superconducting motor prototype under the aforementioned drive methods. This prototype, using commercial rare-earth barium copper oxide (REBCO) tapes, was first connected to a frequency inverter (harmonics tests), and then to an ac power source (starting current tests) and tested at 77 K in liquid nitrogen. The torque under load variations, mechanical power, losses, and harmonics content of the machine were assessed. Key results showed that the motor losses increase due to a high content of harmonics during the soft starting. Consequently, the torque and the mechanical power decreased significantly compared with the direct starting. Nevertheless, the latter may present some risks for the physical integrity of the rotor as a large transient current can flow in the winding accompanied by higher mechanical stresses. For industrial motors of more outstanding power ratings with a wide range of applications requiring one or the other starting methods, it is necessary to further mature the design with machines of increasing rated power if such devices ought to be used reliably in the industry (in the kW range and above).
- 22 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (8) , 1-6
Response of a Trapped Flux Superconducting Motor to Two Drive Methods
This work presents the starting of a trapped flux superconducting motor considering two drive methods: direct starting (using an ac power source) and soft starting (using a frequency inverter). These two methods present different characteristics that are expected to affect the behavior of the superconducting motor. For the direct starting, there is inrush current but no harmonics. On the contrary, for soft starting, there are harmonics but no inrush current. To understand the impacts of the starting current or the harmonics on the performance of superconducting motors, different tests were carried out on a superconducting motor prototype under the aforementioned drive methods. This prototype, using commercial rare-earth barium copper oxide (REBCO) tapes, was first connected to a frequency inverter (harmonics tests), and then to an ac power source (starting current tests) and tested at 77 K in liquid nitrogen. The torque under load variations, mechanical power, losses, and harmonics content of the machine were assessed. Key results showed that the motor losses increase due to a high content of harmonics during the soft starting. Consequently, the torque and the mechanical power decreased significantly compared with the direct starting. Nevertheless, the latter may present some risks for the physical integrity of the rotor as a large transient current can flow in the winding accompanied by higher mechanical stresses. For industrial motors of more outstanding power ratings with a wide range of applications requiring one or the other starting methods, it is necessary to further mature the design with machines of increasing rated power if such devices ought to be used reliably in the industry (in the kW range and above).
- 6 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (7) , 1-5
Performance Comparison of Superconducting Machines With Induction Motors
The demand for high power density electrical machines grows in aircraft and ships for their propulsion systems. Superconducting machines can be an attractive alternative for these applications. In this context, the present work presents a study comparing a superconducting motor with a squirrel-cage induction motor operating at room and cryogenic temperatures. The superconducting electric machine uses 2G tapes stacked on the rotor. The study is based on experiments with bench prototypes of conventional induction motors and superconducting motors having equal dimensions. The rotor is composed of three superconducting tape rows, which are stacked in a spiral shape around a soft ferromagnetic core. The operating principle of this machine considers the interaction of the rotating field produced by the stator with the magnetic field trapped in the superconducting tapes stacked in the rotor. A commercial 0.5-hp squirrel-cage induction motor was adapted for the tests in different circumstances for operation in an extensive temperature range. The induction machine was tested at liquid nitrogen temperature and room temperature. The results of all prototypes were compared. The authors observed that, up to 80% of the rated load, the superconducting machine works in a synchronous regime, and for higher torque’s levels, it is asynchronous. Besides, it increased the torque 1.24 times and 2.43 times for the induction motor operating at room temperature and 77 K, respectively. The results showed that this superconducting machine has the potential for high power density applications.
- 6 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (7) , 1-5
Performance Comparison of Superconducting Machines With Induction Motors
The demand for high power density electrical machines grows in aircraft and ships for their propulsion systems. Superconducting machines can be an attractive alternative for these applications. In this context, the present work presents a study comparing a superconducting motor with a squirrel-cage induction motor operating at room and cryogenic temperatures. The superconducting electric machine uses 2G tapes stacked on the rotor. The study is based on experiments with bench prototypes of conventional induction motors and superconducting motors having equal dimensions. The rotor is composed of three superconducting tape rows, which are stacked in a spiral shape around a soft ferromagnetic core. The operating principle of this machine considers the interaction of the rotating field produced by the stator with the magnetic field trapped in the superconducting tapes stacked in the rotor. A commercial 0.5-hp squirrel-cage induction motor was adapted for the tests in different circumstances for operation in an extensive temperature range. The induction machine was tested at liquid nitrogen temperature and room temperature. The results of all prototypes were compared. The authors observed that, up to 80% of the rated load, the superconducting machine works in a synchronous regime, and for higher torque’s levels, it is asynchronous. Besides, it increased the torque 1.24 times and 2.43 times for the induction motor operating at room temperature and 77 K, respectively. The results showed that this superconducting machine has the potential for high power density applications.
- 18 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (5) , 1-4
2-D Modeling of HTS Coils With $T$-$A$ Formulation: How to Handle Different Coupling ScenariosNumerical models based on the finite-element method are popular tools for investigating the macroscopic electromagnetic behavior of high-temperature superconductor (HTS) applications. This article explains how to use the$T$ -$A$ formulation in COMSOL Multiphysics for modeling HTS coils in 2-D with different coupling scenarios between the turns. First we consider a racetrack coil wound from one piece of superconducting tape. Then, we consider a coil obtained by winding a cable composed of different HTS tapes. In the latter case, the tape turns are either electrically connected along their entire length or just at the two ends of the coil: in the model, these two different types of electrical connection are implemented with the help of the electrical circuit module. The current density distributions and the ac losses of the coils in the different coupling scenarios are compared and discussed. The limits of applicability of the presented approach are pointed out. The model is developed for the straight section of racetrack coils, but can be easily adapted to axisymmetric geometries.- 18 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (5) , 1-4
2-D Modeling of HTS Coils With $T$-$A$ Formulation: How to Handle Different Coupling ScenariosNumerical models based on the finite-element method are popular tools for investigating the macroscopic electromagnetic behavior of high-temperature superconductor (HTS) applications. This article explains how to use the$T$ -$A$ formulation in COMSOL Multiphysics for modeling HTS coils in 2-D with different coupling scenarios between the turns. First we consider a racetrack coil wound from one piece of superconducting tape. Then, we consider a coil obtained by winding a cable composed of different HTS tapes. In the latter case, the tape turns are either electrically connected along their entire length or just at the two ends of the coil: in the model, these two different types of electrical connection are implemented with the help of the electrical circuit module. The current density distributions and the ac losses of the coils in the different coupling scenarios are compared and discussed. The limits of applicability of the presented approach are pointed out. The model is developed for the straight section of racetrack coils, but can be easily adapted to axisymmetric geometries.