Yu-En Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yu-En Wu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Che-Ming Chang
Department of Electronic Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, Taiwan, R.O.C.
2 shared publicationsKuo Chan Huang
National Kaohsiung First University of Science and Technology
2 shared publicationsKuo-Chan Huang
Department of Electronic Engineering, National Kaohsiung First University of Science and Technology, Taiwan, R.O.C.
2 shared publicationsKuo‐Chan Huang
Department of Electronic Engineering National Kaohsiung First University of Science and Technology Kaohsiung Taiwan
2 shared publications- Shiu-Liang Hsiao
Department of Electronic Engineering, National Kaohsiung University of Science and Technology, Kaohsiung 811213, Taiwan
2 shared publications Bo-Hau Pan
Department of Electronic Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, Taiwan
1 shared publication
Latest Publications
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (12) , 21630-21644
Multifunction Isolated Three-Port Bidirectional DC/DC Converter for Hybrid Energy Systems
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (12) , 21630-21644
Multifunction Isolated Three-Port Bidirectional DC/DC Converter for Hybrid Energy Systems
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Power Electronics Magazine
- Vol. 13 (3) , 26-40
Two Novel Energy Management Control Strategies for Distributed Energy Systems
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Power Electronics Magazine
- Vol. 13 (3) , 26-40
Two Novel Energy Management Control Strategies for Distributed Energy Systems
- Open Access
- 11 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 7, 1635-1651
Modular High-Efficiency Bidirectional Isolated DC/DC Converter With Synchronous Control for Energy Storage System
This study proposes a modular, high-efficiency bidirectional isolated DC/DC converter with synchronous control. The converter adopts a modular design, where the power of a single module is 500 W. Paralleling three modules with synchronous control allows the total power rating of the converter to reach 1.5 kW. The modular architecture allows flexibility to adjust according to the application requirements, thereby reducing the development cost. Both step-up and -down operations only require a single pair of complementary signals, which significantly reduces the control complexity. Furthermore, the design provides electrical isolation, enhancing the operational safety, while some switches achieve zero voltage switching (ZVS), thereby minimizing the switching losses. The feasibility and the correctness of the proposed converter are verified through theoretical analysis, software simulation, and hardware implementation. The experimental results show that the maximum efficiency of a single module reaches 97.12% and 97.11% in the step-up and -down modes, respectively. For the three modules operating in parallel, the maximum efficiency reaches 96.1% and 96% in the step-up and -down modes, respectively.
- 11 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 7, 1635-1651
Open AccessModular High-Efficiency Bidirectional Isolated DC/DC Converter With Synchronous Control for Energy Storage System
This study proposes a modular, high-efficiency bidirectional isolated DC/DC converter with synchronous control. The converter adopts a modular design, where the power of a single module is 500 W. Paralleling three modules with synchronous control allows the total power rating of the converter to reach 1.5 kW. The modular architecture allows flexibility to adjust according to the application requirements, thereby reducing the development cost. Both step-up and -down operations only require a single pair of complementary signals, which significantly reduces the control complexity. Furthermore, the design provides electrical isolation, enhancing the operational safety, while some switches achieve zero voltage switching (ZVS), thereby minimizing the switching losses. The feasibility and the correctness of the proposed converter are verified through theoretical analysis, software simulation, and hardware implementation. The experimental results show that the maximum efficiency of a single module reaches 97.12% and 97.11% in the step-up and -down modes, respectively. For the three modules operating in parallel, the maximum efficiency reaches 96.1% and 96% in the step-up and -down modes, respectively.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Power Electronics Magazine
- Vol. 13 (1) , 38-52
High Step-Up DC–DC Converter With Wide Input Voltage Range and High Voltage Gain Ratio
This article proposes a high step-up dc–dc converter for photovoltaic systems, characterized by a wide input voltage range and high voltage gain ratio. The proposed converter consists of two switches, two sets of coupled inductors, and a multiplier circuit. Both switches are driven by the same pulse-width modulation control signal, enabling a simple control strategy to accommodate a wide input voltage range of 24–48 V. The proposed topology achieves a high voltage gain without requiring an excessively large duty cycle or turn ratio. Additionally, the leakage energy of the coupled inductors is recycled to improve conversion efficiency and mitigate voltage spikes across the switches. A 1-kW converter circuit is implemented, and its feasibility is verified through steady-state analysis, software simulations, and hardware implementation. The maximum efficiencies at input voltages of 24 V, 36 V, and 48 V are 95.56%, 95.8%, and 96.24%, respectively.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Power Electronics Magazine
- Vol. 13 (1) , 38-52
High Step-Up DC–DC Converter With Wide Input Voltage Range and High Voltage Gain Ratio
This article proposes a high step-up dc–dc converter for photovoltaic systems, characterized by a wide input voltage range and high voltage gain ratio. The proposed converter consists of two switches, two sets of coupled inductors, and a multiplier circuit. Both switches are driven by the same pulse-width modulation control signal, enabling a simple control strategy to accommodate a wide input voltage range of 24–48 V. The proposed topology achieves a high voltage gain without requiring an excessively large duty cycle or turn ratio. Additionally, the leakage energy of the coupled inductors is recycled to improve conversion efficiency and mitigate voltage spikes across the switches. A 1-kW converter circuit is implemented, and its feasibility is verified through steady-state analysis, software simulations, and hardware implementation. The maximum efficiencies at input voltages of 24 V, 36 V, and 48 V are 95.56%, 95.8%, and 96.24%, respectively.
- Open Access
Wide-Input High-Step-Up DC–DC Converter with High Efficiency and High Voltage Gain
This study proposes a wide-input high-step-up DC–DC converter with high efficiency and high voltage conversion ratio. Two coupled inductors were adopted to achieve a parallel-charging and series-discharging energy transfer mechanism, and a voltage multiplier circuit was integrated to increase the voltage gain. The proposed topology uses a single pulse width modulation signal to drive two main switches synchronously, resulting in a low switch count and simple control circuit, concurrently achieving a wide input voltage range of 24 V to 48 V. The proposed converter comprises an active switched inductor combined with a voltage multiplier circuit, achieving a high voltage gain without relying on high duty cycle operation or high-turns-ratio design. The leakage energy of the coupled inductors was recycled through a passive-clamp circuit, effectively suppressing the voltage spikes of the switching devices and reducing their voltage stress. Finally, a 1 kW converter was implemented to verify the feasibility of the proposed topology through steady-state analysis, circuit simulation, and hardware experiments. The maximum efficiencies achieved were 94.7% and 96.2% at input voltages of 24 V and 48 V, respectively.
Open AccessWide-Input High-Step-Up DC–DC Converter with High Efficiency and High Voltage Gain
This study proposes a wide-input high-step-up DC–DC converter with high efficiency and high voltage conversion ratio. Two coupled inductors were adopted to achieve a parallel-charging and series-discharging energy transfer mechanism, and a voltage multiplier circuit was integrated to increase the voltage gain. The proposed topology uses a single pulse width modulation signal to drive two main switches synchronously, resulting in a low switch count and simple control circuit, concurrently achieving a wide input voltage range of 24 V to 48 V. The proposed converter comprises an active switched inductor combined with a voltage multiplier circuit, achieving a high voltage gain without relying on high duty cycle operation or high-turns-ratio design. The leakage energy of the coupled inductors was recycled through a passive-clamp circuit, effectively suppressing the voltage spikes of the switching devices and reducing their voltage stress. Finally, a 1 kW converter was implemented to verify the feasibility of the proposed topology through steady-state analysis, circuit simulation, and hardware experiments. The maximum efficiencies achieved were 94.7% and 96.2% at input voltages of 24 V and 48 V, respectively.
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- p. 1
Multifunctional High Step-Up Nonisolated Three-Port DC-DC Converter for Hybrid Energy Systems
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- p. 1
Open AccessMultifunctional High Step-Up Nonisolated Three-Port DC-DC Converter for Hybrid Energy Systems
- Open Access
- 1 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 1724-1736
Wide-Range Input-Isolated DC–DC Ultrahigh-Step-Down Converter Containing Buck and Half-Bridge Topologies for Low-Power Applications
- 1 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 1724-1736
Open AccessWide-Range Input-Isolated DC–DC Ultrahigh-Step-Down Converter Containing Buck and Half-Bridge Topologies for Low-Power Applications
- 4 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (2) , 953-962
A Novel Single-Switch High Step-Up DC-DC Converter With High-Voltage Conversion Ratio
This paper proposes a novel high step-up DC-DC converter comprising a single switch and a three-winding coupled inductor. By using only one switch, the proposed converter simplifies control by requiring only one set of PWM signals and eliminates the need for operating at extremely high duty cycles or high turns ratios to achieve the desired gain ratio. Moreover, the converter achieves remarkable voltage gain through a voltage multiplier cell and a three-winding coupled inductor. This paper employed a 500W high step-up converter to confirm the correctness and feasibility of the proposed converter through steady-state analysis, software simulations, and hardware implementation. The measured maximum efficiency reached 95.8% when operated under 150W.
- 4 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (2) , 953-962
A Novel Single-Switch High Step-Up DC-DC Converter With High-Voltage Conversion Ratio
This paper proposes a novel high step-up DC-DC converter comprising a single switch and a three-winding coupled inductor. By using only one switch, the proposed converter simplifies control by requiring only one set of PWM signals and eliminates the need for operating at extremely high duty cycles or high turns ratios to achieve the desired gain ratio. Moreover, the converter achieves remarkable voltage gain through a voltage multiplier cell and a three-winding coupled inductor. This paper employed a 500W high step-up converter to confirm the correctness and feasibility of the proposed converter through steady-state analysis, software simulations, and hardware implementation. The measured maximum efficiency reached 95.8% when operated under 150W.
- 13 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (5) , 5037-5051
Dual-Input Interleaved Bidirectional DC–DC Converter for Light Electric Vehicles
This paper proposes a dual-input interleaved bidirectional DC-DC converter for light electric vehicles (EVs). The low-voltage side of the proposed converter consists of batteries and supercapacitors (UCs). One set of complementary PWN signals with a phase difference of 180° is used to control the switch of the proposed converter to achieve the desired voltage gain with a fixed duty cycle. Hence, compared to the interleaved topology realized by converters in parallel, the proposed converter can achieve low-side current continuity and reduce the input current ripple by using the complementary PWN signals strategies. Moreover, the voltage gain can be further improved by adjusting the turns ratio of the coupled inductor of the converter, meanwhile, the voltage stress on the switches can be reduced. The operational principles of the proposed converter are introduced. An experimental bidirectional converter with 500W is implemented to verify the feasibility of the proposed bidirectional converters. The test results show that the highest efficiency of the step-up and step-down modes is 98% and 96.9%, respectively.
- 13 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (5) , 5037-5051
Dual-Input Interleaved Bidirectional DC–DC Converter for Light Electric Vehicles
This paper proposes a dual-input interleaved bidirectional DC-DC converter for light electric vehicles (EVs). The low-voltage side of the proposed converter consists of batteries and supercapacitors (UCs). One set of complementary PWN signals with a phase difference of 180° is used to control the switch of the proposed converter to achieve the desired voltage gain with a fixed duty cycle. Hence, compared to the interleaved topology realized by converters in parallel, the proposed converter can achieve low-side current continuity and reduce the input current ripple by using the complementary PWN signals strategies. Moreover, the voltage gain can be further improved by adjusting the turns ratio of the coupled inductor of the converter, meanwhile, the voltage stress on the switches can be reduced. The operational principles of the proposed converter are introduced. An experimental bidirectional converter with 500W is implemented to verify the feasibility of the proposed bidirectional converters. The test results show that the highest efficiency of the step-up and step-down modes is 98% and 96.9%, respectively.
- Open Access
High Efficiency and High Voltage Conversion Ratio Bidirectional Isolated DC–DC Converter for Energy Storage Systems
In this paper, a novel high-efficiency bidirectional isolated DC–DC converter that can be applied to an energy storage system for battery charging and discharging is proposed. By integrating a coupled inductor and switched-capacitor voltage doubler, the proposed converter can achieve isolation and bidirectional power flow. The proposed topology comprises five switches and a common core coupled inductor that uses only a set of complementary pulse-width-modulated signals to control and achieve high voltage gain without requiring high turn ratios or excessive duty cycles. Moreover, the proposed topology can recover the leakage inductance energy to improve the conversion efficiency. The main switches exhibit zero-voltage switching, which reduces the switching losses. A 500-W bidirectional converter is used to verify the feasibility of the proposed bidirectional converter through theoretical analysis and experiments. The experimental results indicate that the highest efficiency of the proposed converter in the step-up and step-down modes is 97.59% and 96.5%, respectively.
Open AccessHigh Efficiency and High Voltage Conversion Ratio Bidirectional Isolated DC–DC Converter for Energy Storage Systems
In this paper, a novel high-efficiency bidirectional isolated DC–DC converter that can be applied to an energy storage system for battery charging and discharging is proposed. By integrating a coupled inductor and switched-capacitor voltage doubler, the proposed converter can achieve isolation and bidirectional power flow. The proposed topology comprises five switches and a common core coupled inductor that uses only a set of complementary pulse-width-modulated signals to control and achieve high voltage gain without requiring high turn ratios or excessive duty cycles. Moreover, the proposed topology can recover the leakage inductance energy to improve the conversion efficiency. The main switches exhibit zero-voltage switching, which reduces the switching losses. A 500-W bidirectional converter is used to verify the feasibility of the proposed bidirectional converter through theoretical analysis and experiments. The experimental results indicate that the highest efficiency of the proposed converter in the step-up and step-down modes is 97.59% and 96.5%, respectively.