Antonio P. Rodrigues
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Antonio P. Rodrigues has a total of 98 co-authors. Here are the top co-authors by number of shared publications:
- Jorge Sousa
Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa, Portugal
35 shared publications - Bruno Goncalves
Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa, Portugal
34 shared publications - Carlos A. F. Varandas
Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, 1049-001, Portugal
32 shared publications - António Joaquim Nunes Batista
Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa, Portugal
30 shared publications - Miguel Correia
Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa, Portugal
30 shared publications - Bernardo Brotas Carvalho
Instituto de Plasmas e Fusão Nuclear Instituto Superior Técnico, Lisbon, Portugal
25 shared publications
Latest Publications
- 1 November 2019
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 14 (11) , C11025
MTCA control and data acquisition platform for Plasma Diagnostics
- 1 November 2019
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 14 (11) , C11025
MTCA control and data acquisition platform for Plasma Diagnostics
- 1 April 2018
- Published by Elsevier in Fusion Engineering and Design
- Vol. 129, 247-252
On the control system preparation for ELM pacing with vertical kicks experiments at TCV
- 1 April 2018
- Published by Elsevier in Fusion Engineering and Design
- Vol. 129, 247-252
On the control system preparation for ELM pacing with vertical kicks experiments at TCV
- 1 March 2018
- Published by Elsevier in Fusion Engineering and Design
- Vol. 128, 138-142
Taking advantage of the intercommunication features of IPMCs in ATCA CDAQ systems
- 1 March 2018
- Published by Elsevier in Fusion Engineering and Design
- Vol. 128, 138-142
Taking advantage of the intercommunication features of IPMCs in ATCA CDAQ systems
- 1 November 2017
- Published by Elsevier in Fusion Engineering and Design
- Vol. 124, 1187-1190
Interfacing ATCA Hot-Swap with PCIe Hot-Plug for high-availability instrumentation in critical systems
- 1 November 2017
- Published by Elsevier in Fusion Engineering and Design
- Vol. 124, 1187-1190
Interfacing ATCA Hot-Swap with PCIe Hot-Plug for high-availability instrumentation in critical systems
- 1 November 2017
- Published by Elsevier in Fusion Engineering and Design
- Vol. 123, 732-736
EPICS device support for an ATCA CDAQ Board with hot-plug capabilities
- 1 November 2017
- Published by Elsevier in Fusion Engineering and Design
- Vol. 123, 732-736
EPICS device support for an ATCA CDAQ Board with hot-plug capabilities
- 1 November 2017
- Published by Elsevier in Fusion Engineering and Design
- Vol. 123, 703-706
PCIe hot-plug event handling tasks using PICMG standard interrupt mechanism for ATCA based instrumentation
- 1 November 2017
- Published by Elsevier in Fusion Engineering and Design
- Vol. 123, 703-706
PCIe hot-plug event handling tasks using PICMG standard interrupt mechanism for ATCA based instrumentation
- 27 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 63 (3) , 1645-1649
FPGA Remote Update for Nuclear Environments
In recent years there has been a growing interest to use reconfigurable modules, based on field-programmable gate array (FPGA) devices, in nuclear environments. One of the requirements for these types of modules, when operating in complex future nuclear power experiments, is their remote update capability. The operational needs of pulsed fusion reactors will lead to a large production of very high energy neutrons (MeV range). The current procurement policies for nuclear installations do not allow exposure of electronics to radiation, except following very strict rules. However, considering the “as low as (is) reasonably achievable” (ALARA) principle with respect to human exposure to radiation, the access to cubicles might be restricted, requiring the remote update of FPGA codes. FPGAs are volatile devices, and their programming code is usually stored in dedicated flash memories for proper configuration during module power-on. This paper presents an alternative method for FPGA remote update, capable to store new FPGA codes in inboard Serial Peripheral Interface (SPI) flash memories. The new method, based on the Xilinx Quick Boot application note and adapted to PCIe protocol, was developed with the KC705 Evaluation Kit from Xilinx and successfully tested in the in-house Advanced Mezzanine Card (AMC) prototype, installed on the ATCA-PTSW-AMC4 carrier module from the ITER Fast Plant System Controller catalogue.
- 27 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 63 (3) , 1645-1649
FPGA Remote Update for Nuclear Environments
In recent years there has been a growing interest to use reconfigurable modules, based on field-programmable gate array (FPGA) devices, in nuclear environments. One of the requirements for these types of modules, when operating in complex future nuclear power experiments, is their remote update capability. The operational needs of pulsed fusion reactors will lead to a large production of very high energy neutrons (MeV range). The current procurement policies for nuclear installations do not allow exposure of electronics to radiation, except following very strict rules. However, considering the “as low as (is) reasonably achievable” (ALARA) principle with respect to human exposure to radiation, the access to cubicles might be restricted, requiring the remote update of FPGA codes. FPGAs are volatile devices, and their programming code is usually stored in dedicated flash memories for proper configuration during module power-on. This paper presents an alternative method for FPGA remote update, capable to store new FPGA codes in inboard Serial Peripheral Interface (SPI) flash memories. The new method, based on the Xilinx Quick Boot application note and adapted to PCIe protocol, was developed with the KC705 Evaluation Kit from Xilinx and successfully tested in the in-house Advanced Mezzanine Card (AMC) prototype, installed on the ATCA-PTSW-AMC4 carrier module from the ITER Fast Plant System Controller catalogue.
- 29 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 62 (6) , 3126-3133
An Optimal Real-Time Controller for Vertical Plasma Stabilization
Modern Tokamaks have evolved from the initial axisymmetric circular plasma shape to an elongated axisymmetric plasma shape that improves the energy confinement, which is one of the key factors to improve fusion reactor performance. However, the elongated plasma cross section introduces a vertical instability that requires a real-time feedback control loop to stabilize the plasma vertical position and velocity. At the Tokamak à Configuration Variable (TCV) in-vessel poloidal field coils driven by fast switching power supplies are used to stabilize highly elongated plasmas. TCV plasma experiments have used a PID algorithm based controller to correct the plasma vertical position. In late 2013 experiments a new optimal real-time controller was tested improving the stability of the plasma. This contribution describes the new optimal real-time controller developed. The choice of the model that describes the plasma response to the actuators is discussed. The high order model that is initially implemented needs the application of a mathematical order reduction and the validation of the new reduced model. The lower order model is used to derive the time optimal control law. A new method for the construction of the switching curves of a bang-bang controller is presented that is based on the state-space trajectories that optimize the time to target of the system. The final control algorithm and its implementation are described and preliminary experimental results are discussed.
- 29 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 62 (6) , 3126-3133
An Optimal Real-Time Controller for Vertical Plasma Stabilization
Modern Tokamaks have evolved from the initial axisymmetric circular plasma shape to an elongated axisymmetric plasma shape that improves the energy confinement, which is one of the key factors to improve fusion reactor performance. However, the elongated plasma cross section introduces a vertical instability that requires a real-time feedback control loop to stabilize the plasma vertical position and velocity. At the Tokamak à Configuration Variable (TCV) in-vessel poloidal field coils driven by fast switching power supplies are used to stabilize highly elongated plasmas. TCV plasma experiments have used a PID algorithm based controller to correct the plasma vertical position. In late 2013 experiments a new optimal real-time controller was tested improving the stability of the plasma. This contribution describes the new optimal real-time controller developed. The choice of the model that describes the plasma response to the actuators is discussed. The high order model that is initially implemented needs the application of a mathematical order reduction and the validation of the new reduced model. The lower order model is used to derive the time optimal control law. A new method for the construction of the switching curves of a bang-bang controller is presented that is based on the state-space trajectories that optimize the time to target of the system. The final control algorithm and its implementation are described and preliminary experimental results are discussed.
- 1 October 2015
- Published by Elsevier in Fusion Engineering and Design
- Vol. 96-97, 760-764
Precision Time Protocol support hardware for ATCA control and data acquisition system
- 1 October 2015
- Published by Elsevier in Fusion Engineering and Design
- Vol. 96-97, 760-764
Precision Time Protocol support hardware for ATCA control and data acquisition system
- 1 October 2015
- Published by Elsevier in Fusion Engineering and Design
- Vol. 96-97, 738-741
PCI express hotplug implementation for ATCA based instrumentation
- 1 October 2015
- Published by Elsevier in Fusion Engineering and Design
- Vol. 96-97, 738-741
PCI express hotplug implementation for ATCA based instrumentation