Paul Elliott Specht

A series of Versalink® P1000 and Mondur CD (polymers of approximately 1000 amu) polyurea samples were loaded with ceria (CeO2) nanoparticles and carbon nanotubes (CNTs), shocked using direct laser impulse testing, and their response was measured by photonic Doppler velocimetry. A novel method for a near universally applicable ablation layer was employed by depositing titanium onto one side of the polyurea nanocomposite disk, followed by a reflective layer of aluminum on the reverse side via sputter deposition. Relative to the 73.6% baseline attenuation of pure P1000 polyurea, nanoparticle addition increased incident-pressure attenuation to up to 88.3%. The ceria nanocomposites exhibited a decreased Hugoniot elastic limit, indicating increased quantities of micropores and microfracture sites to facilitate shock hysteresis. In contrast, CNT nanocomposites displayed an increased initial shock without a visible plastic deformation peak, followed by a slower secondary hysteresis wave as CNT loading increased. These findings can guide the development of composite dampeners for synthetic armors and similar applications.

A new continuum-based mesoscale modeling approach for shock-induced chemical reactions (SICRs) in Ni+Al multilayers is demonstrated in Sandia’s shock physics hydrocode, CTH. The approach utilizes Arrhenius-type kinetics and artificial thermal conduction. Our work builds upon previous efforts to parameterize equations of state for NixAly [J. Appl. Phys. 137, 075102 (2025)], as well as simulations of inert shocks in realistic 2D microstructures [J. Appl. Phys. 137, 225301 (2025)]. To calibrate the reaction kinetics, pairs of the reaction coordinate, R′, vs time are extracted from the molecular dynamics (MD) literature. Here, the MD-informed kinetics are used to simulate the dynamic evolution of pressure and temperature in 2D mesoscale simulations. Overall, the MD-informed kinetics obtained for planar interfaces are too slow, as initial reaction is not observed on a nanosecond time scale. Even with quasi-periodic shock focusing leading to the formation of so-called “hot-spots,” the hot spots are unable to grow and coalesce using the fitted Arrhenius rate constants. However, by increasing the rate constants by two orders of magnitude, SICRs are observed at a shock pressure near 30 GPa, which is supported by experiments. Consequently, these mesoscale simulations suggest that unresolved shear-based mechanical mixing might possibly account for the discrepancies in kinetic rates, with shock-generated intense perturbations, interfacial vortical flows, and elevated temperatures serving as favorable reaction conditions. Future work will calibrate a shear-dependent reaction rate from the MD simulations with realistic interfaces that are wavy, diffuse, and disordered.

This study investigates the inert Hugoniot response, mechanical ignition, and reaction dynamics of Ni(V)+Al multilayers during longitudinal, laser-driven shock compression experiments. Ni(V)+Al multilayers, known for their self-propagating exothermic reactions, were subjected to longitudinal stresses exceeding 50 GPa using the laser shock facility within the Dynamic Compression Sector (DCS) at the Advanced Photon Source (APS). In situ x-ray diffraction (XRD) revealed that Ni(V) and Al were not in equilibrium during compression, with stress discrepancies attributed to twinning, grain structure effects, and/or dislocation density. However, the measured inert Hugoniot closely matched prior experimental and computational studies, confirming the utility of XRD for measuring the equation of state of thin, complex materials. Additionally, reaction was observed at significantly higher stresses than reported previously using laser-launched flyers. This discrepancy suggests a strong influence of externally imposed shear stress on reaction thresholds, which likely arose from deviations in flyer planarity during past experiments. Full reaction of the multilayer occurred within 40 ns after shock-wave passage, evidenced by complete melting of the constituents. Eulerian hydrocode simulations replicated experimental conditions, providing insights into equilibrium dynamics and experimental artifacts. The results highlight how even small shear forces facilitate ignition in Ni(V)+Al multilayers at lower stresses.

Mesoscale modeling of shock waves in Ni+Al multilayers poses significant challenges that are due, in part, to shock-induced chemical reactions. Current modeling approaches utilize reactive molecular dynamics (MD), but they are limited to resolving domains of only a few hundred nanometers. In contrast, actual multilayer superlattices can be tens of micrometers thick, and they exhibit non-ideal (i.e., wavy) interfaces. The second part of our research builds upon previous work developing physically based, thermodynamically complete equations of state for various Ni and Al intermetallic compositions. Here, we introduce a novel workflow for high-fidelity mesoscale simulations of Ni+Al multilayers using a continuum hydrocode. By increasing the simulation domain size beyond MD limitations (e.g., 2×6μm2) and incorporating explicit interfacial roughness, we investigate the shock response of Ni+Al multilayers at previously unexplored scales. Our experimental design encompasses nine multilayer geometries with varying roughness amplitudes and tilt angles (θ=15°, 30°, and 45°), alongside 19 flyer impact velocities ranging from 0.3 to 3.0 km/s, resulting in a total of 171 high-fidelity simulations. The bulk shock state from inert 2D mesoscale simulations aligns with the law of mixtures, while temperature and pressure fluctuations strongly correlate with multilayer geometry types. A new metric dubbed the “hot spot probability integral” shows a greater dependence on a tilt angle than interfacial roughness.

The eutectic alloy AlSi10Mg is commonly used for additive manufacturing (AM), as its high Si content improves printability. This abundance of Si forms Si-rich precipitates whose structure is heavily dependent on the thermal history and have been shown to strongly influence its mechanical properties. In this presentation we present the results of experiments to study the effect of the Si-structure on the equation of state and spallation strength of AM AlSi10Mg.