Krishnamurthy Nagendra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Krishnamurthy Nagendra has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Danesh K. Tafti
4 shared publications- Danesh K. Tafti
Virginia Polytechnic Institute and State University
4 shared publications Kamal Viswanath
2 shared publicationsA.K. Viswanathan
Modine Manufacturing Company, Racine, WI, USA
1 shared publicationAroon K. Viswanathan
1 shared publicationD. K. Tafti
Virginia Tech 2 Department of Mechanical Engineering Blacksburg, Virginia 24061, USA
1 shared publication
Latest Publications
- 17 June 2019
- Published by ASME International
LES-Conjugate Heat Transfer Analysis of a Ribbed Cooling Passage Using the Immersed Boundary Method
The present study focuses on evaluating fully-coupled conjugate heat transfer simulation in a ribbed cooling passage with a fully developed flow assumption using LES with the immersed boundary method (IBM-LES-CHT). The IBM-LES and the IBM-CHT frameworks are validated prior to the main simulations by simulating purely convective heat transfer in the ribbed duct, and a laminar boundary layer flow over a 2D flat plate with heat conduction, respectively. For the main conjugate simulations, a ribbed duct geometry with a blockage ratio of 0.3 is simulated at a bulk Reynolds number of 10,000 with a conjugate boundary condition applied to the rib surface. The nominal Biot number is kept at 1, which is similar to the comparative experiment. As a means to overcome a large time scale disparity between the fluid and the solid regions, the use of a high artificial solid thermal diffusivity is compared to the physical diffusivity. It is shown that while the diffusivity impacts the instantaneous fluctuations in temperature, heat transfer and Nusselt numbers, it has an insignificantly small effect on the mean Nusselt number. Comparison between IBM-LES-CHT and iso-flux heat transfer simulations shows that the iso-flux case predicts higher local Nusselt numbers at the back face of the rib. Furthermore, the local Nusselt number augmentation ratio (EF) predicted by IBM-LES-CHT is compared to experiment and another LES conjugate simulation. Even though there is a mismatch between IBM-LES-CHT predictions and other two studies at the front face of the rib, the area-averaged EF compares reasonably well in other regions between IBM-LES-CHT prediction and the comparative studies.
- 17 June 2019
- Published by ASME International
LES-Conjugate Heat Transfer Analysis of a Ribbed Cooling Passage Using the Immersed Boundary Method
The present study focuses on evaluating fully-coupled conjugate heat transfer simulation in a ribbed cooling passage with a fully developed flow assumption using LES with the immersed boundary method (IBM-LES-CHT). The IBM-LES and the IBM-CHT frameworks are validated prior to the main simulations by simulating purely convective heat transfer in the ribbed duct, and a laminar boundary layer flow over a 2D flat plate with heat conduction, respectively. For the main conjugate simulations, a ribbed duct geometry with a blockage ratio of 0.3 is simulated at a bulk Reynolds number of 10,000 with a conjugate boundary condition applied to the rib surface. The nominal Biot number is kept at 1, which is similar to the comparative experiment. As a means to overcome a large time scale disparity between the fluid and the solid regions, the use of a high artificial solid thermal diffusivity is compared to the physical diffusivity. It is shown that while the diffusivity impacts the instantaneous fluctuations in temperature, heat transfer and Nusselt numbers, it has an insignificantly small effect on the mean Nusselt number. Comparison between IBM-LES-CHT and iso-flux heat transfer simulations shows that the iso-flux case predicts higher local Nusselt numbers at the back face of the rib. Furthermore, the local Nusselt number augmentation ratio (EF) predicted by IBM-LES-CHT is compared to experiment and another LES conjugate simulation. Even though there is a mismatch between IBM-LES-CHT predictions and other two studies at the front face of the rib, the area-averaged EF compares reasonably well in other regions between IBM-LES-CHT prediction and the comparative studies.
- 1 May 2017
- Published by Elsevier in Powder Technology
- Vol. 313, 332-343
Evaluation of drag correlations using particle resolved simulations of spheres and ellipsoids in assembly
- 1 May 2017
- Published by Elsevier in Powder Technology
- Vol. 313, 332-343
Evaluation of drag correlations using particle resolved simulations of spheres and ellipsoids in assembly
- 1 May 2015
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 84, 463-474
A sub-pore model for multi-scale reaction–diffusion problems in porous media
- 1 May 2015
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 84, 463-474
A sub-pore model for multi-scale reaction–diffusion problems in porous media
- 13 August 2014
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 372 (2022) , 20130322
Large eddy simulation for predicting turbulent heat transfer in gas turbines
Blade cooling technology will play a critical role in the next generation of propulsion and power generation gas turbines. Accurate prediction of blade metal temperature can avoid the use of excessive compressed bypass air and allow higher turbine inlet temperature, increasing fuel efficiency and decreasing emissions. Large eddy simulation (LES) has been established to predict heat transfer coefficients with good accuracy under various non-canonical flows, but is still limited to relatively simple geometries and low Reynolds numbers. It is envisioned that the projected increase in computational power combined with a drop in price-to-performance ratio will make system-level simulations using LES in complex blade geometries at engine conditions accessible to the design process in the coming one to two decades. In making this possible, two key challenges are addressed in this paper: working with complex intricate blade geometries and simulating high-Reynolds-number ( Re ) flows. It is proposed to use the immersed boundary method (IBM) combined with LES wall functions. A ribbed duct at Re =20 000 is simulated using the IBM, and a two-pass ribbed duct is simulated at Re =100 000 with and without rotation (rotation number Ro =0.2) using LES with wall functions. The results validate that the IBM is a viable alternative to body-conforming grids and that LES with wall functions reproduces experimental results at a much lower computational cost.
- 13 August 2014
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 372 (2022) , 20130322
Large eddy simulation for predicting turbulent heat transfer in gas turbines
Blade cooling technology will play a critical role in the next generation of propulsion and power generation gas turbines. Accurate prediction of blade metal temperature can avoid the use of excessive compressed bypass air and allow higher turbine inlet temperature, increasing fuel efficiency and decreasing emissions. Large eddy simulation (LES) has been established to predict heat transfer coefficients with good accuracy under various non-canonical flows, but is still limited to relatively simple geometries and low Reynolds numbers. It is envisioned that the projected increase in computational power combined with a drop in price-to-performance ratio will make system-level simulations using LES in complex blade geometries at engine conditions accessible to the design process in the coming one to two decades. In making this possible, two key challenges are addressed in this paper: working with complex intricate blade geometries and simulating high-Reynolds-number ( Re ) flows. It is proposed to use the immersed boundary method (IBM) combined with LES wall functions. A ribbed duct at Re =20 000 is simulated using the IBM, and a two-pass ribbed duct is simulated at Re =100 000 with and without rotation (rotation number Ro =0.2) using LES with wall functions. The results validate that the IBM is a viable alternative to body-conforming grids and that LES with wall functions reproduces experimental results at a much lower computational cost.
- 1 June 2014
- Published by Elsevier in Journal of Computational Physics
- Vol. 267, 225-246
A new approach for conjugate heat transfer problems using immersed boundary method for curvilinear grid based solvers
- 1 June 2014
- Published by Elsevier in Journal of Computational Physics
- Vol. 267, 225-246
A new approach for conjugate heat transfer problems using immersed boundary method for curvilinear grid based solvers
- 28 February 2014
- Published by ASME International in Journal of Fluids Engineering
- Vol. 136 (4) , 040908
Flows Through Reconstructed Porous Media Using Immersed Boundary Methods
Understanding flow through real porous media is of considerable importance given their significance in a wide range of applications. Direct numerical simulations of such flows are very useful in their fundamental understanding. Past works have focused mainly on ordered and disordered arrays of regular shaped structures such as cylinders or spheres to emulate porous media. More recently, extension of these studies to more realistic pore spaces are available in the literature highlighting the enormous potential of such studies in helping the fundamental understanding of pore-level flow physics. In an effort to advance the simulation of realistic porous media flows further, an immersed boundary method (IBM) framework capable of simulating flows through arbitrary surface contours is used in conjunction with a stochastic reconstruction procedure based on simulated annealing. The developed framework is tested in a two-dimensional channel with two types of porous sections—one created using a random assembly of square blocks and another using the stochastic reconstruction procedure. Numerous simulations are performed to demonstrate the capability of the developed framework. The computed pressure drops across the porous section are compared with predictions from the Darcy–Forchheimer equation for media composed of different structure sizes. Finally, the developed methodology is applied to study CO2 diffusion in porous spherical particles of varying porosities.
- 28 February 2014
- Published by ASME International in Journal of Fluids Engineering
- Vol. 136 (4) , 040908
Flows Through Reconstructed Porous Media Using Immersed Boundary Methods
Understanding flow through real porous media is of considerable importance given their significance in a wide range of applications. Direct numerical simulations of such flows are very useful in their fundamental understanding. Past works have focused mainly on ordered and disordered arrays of regular shaped structures such as cylinders or spheres to emulate porous media. More recently, extension of these studies to more realistic pore spaces are available in the literature highlighting the enormous potential of such studies in helping the fundamental understanding of pore-level flow physics. In an effort to advance the simulation of realistic porous media flows further, an immersed boundary method (IBM) framework capable of simulating flows through arbitrary surface contours is used in conjunction with a stochastic reconstruction procedure based on simulated annealing. The developed framework is tested in a two-dimensional channel with two types of porous sections—one created using a random assembly of square blocks and another using the stochastic reconstruction procedure. Numerous simulations are performed to demonstrate the capability of the developed framework. The computed pressure drops across the porous section are compared with predictions from the Darcy–Forchheimer equation for media composed of different structure sizes. Finally, the developed methodology is applied to study CO2 diffusion in porous spherical particles of varying porosities.
- 1 February 2014
- Published by AIP Publishing in Physics of Fluids
- Vol. 26 (2) , 021901
Straight-line climbing flight aerodynamics of a fruit bat
From flight data obtained on a fruit bat, Cynopterus brachyotis, a kinematic model for straight-line flapping motion is extracted and analyzed in a computational fluid dynamics (CFD) framework to gain insight into the complexity of bat flight. The intricate functional mechanics and architecture of the bat wings set it apart from other vertebrate flight. The extracted kinematic model is simulated for a range of Reynolds numbers, to observe the effect these phenomena have on the unsteady transient mechanisms of the flow produced by the flapping wings. The Strouhal number calculated from the data is high indicating that the oscillatory motion dominates the flow physics. From the obtained data, the bat exhibits fine control of its mechanics by actively varying wing camber, wing area, torsional rotation of the wing, forward and backward translational sweep of the wing, and wing conformation to dictate the fluid dynamics. As is common in flapping flight, the primary force generation is through the attached unsteady vortices on the wing surface. The bat through varying the wing camber and the wing area modulates this force output. The power requirement for the kinematics is analyzed and correlated with the aerodynamic performance.
- 1 February 2014
- Published by AIP Publishing in Physics of Fluids
- Vol. 26 (2) , 021901
Straight-line climbing flight aerodynamics of a fruit bat
From flight data obtained on a fruit bat, Cynopterus brachyotis, a kinematic model for straight-line flapping motion is extracted and analyzed in a computational fluid dynamics (CFD) framework to gain insight into the complexity of bat flight. The intricate functional mechanics and architecture of the bat wings set it apart from other vertebrate flight. The extracted kinematic model is simulated for a range of Reynolds numbers, to observe the effect these phenomena have on the unsteady transient mechanisms of the flow produced by the flapping wings. The Strouhal number calculated from the data is high indicating that the oscillatory motion dominates the flow physics. From the obtained data, the bat exhibits fine control of its mechanics by actively varying wing camber, wing area, torsional rotation of the wing, forward and backward translational sweep of the wing, and wing conformation to dictate the fluid dynamics. As is common in flapping flight, the primary force generation is through the attached unsteady vortices on the wing surface. The bat through varying the wing camber and the wing area modulates this force output. The power requirement for the kinematics is analyzed and correlated with the aerodynamic performance.
- 10 January 2014
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Climbing Flight of a Fruit Bat Deconstructed
- 10 January 2014
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Climbing Flight of a Fruit Bat Deconstructed
- 6 November 2013
- Published by WITPRESS LTD.
- p. 1-37
Gas-Side Fouling of Fin Surfaces in Exhaust Gas Recirculators
- 6 November 2013
- Published by WITPRESS LTD.
- p. 1-37
Gas-Side Fouling of Fin Surfaces in Exhaust Gas Recirculators
- 8 July 2012
- Published by ASME International
- p. 1375-1383
Flows Through Reconstructed Porous Media Using Immersed Boundary Methods
Understanding of the flows through real porous media is of considerable importance given their usage in a wide range of applications. Direct numerical simulations of such flows could be vastly informational but are rarely available in literature owing to the difficulty in simulating flows around complex surface contours that generally constitute porous media. In an effort to better the understanding of such flows, an immersed boundary method (IBM) framework capable of simulating flows through arbitrary surface contours is developed. For simulation of realistic porous media, a stochastic reconstruction procedure based on simulated annealing is utilized. Detailed studies to validate the results are undertaken. Further, numerous calculations are performed on flows through two-dimensional porous channels. The obtained results are compared with the analytical results from Darcy-Forchheimer equation. A study of the effect of varying sizes of the porous structures in such flows shows the increasing deviation from Darcy-Forchheimer equation as the size becomes significant in comparison to the channel height highlighting the need for such a framework and more such DNS studies.
- 8 July 2012
- Published by ASME International
- p. 1375-1383
Flows Through Reconstructed Porous Media Using Immersed Boundary Methods
Understanding of the flows through real porous media is of considerable importance given their usage in a wide range of applications. Direct numerical simulations of such flows could be vastly informational but are rarely available in literature owing to the difficulty in simulating flows around complex surface contours that generally constitute porous media. In an effort to better the understanding of such flows, an immersed boundary method (IBM) framework capable of simulating flows through arbitrary surface contours is developed. For simulation of realistic porous media, a stochastic reconstruction procedure based on simulated annealing is utilized. Detailed studies to validate the results are undertaken. Further, numerous calculations are performed on flows through two-dimensional porous channels. The obtained results are compared with the analytical results from Darcy-Forchheimer equation. A study of the effect of varying sizes of the porous structures in such flows shows the increasing deviation from Darcy-Forchheimer equation as the size becomes significant in comparison to the channel height highlighting the need for such a framework and more such DNS studies.