Aydın Rüşen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Aydın Rüşen has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Mehmet Ali Topçu
4 shared publications- Mehmet Ali Topçu
Karamanoğlu Mehmetbey Üniversitesi
4 shared publications Muazzez Çelik Karakaya
3 shared publicationsAhmet Geveci
Department of Metallurgical and Materials Engineering, Middle East Technical University, Ankara, Turkey
2 shared publicationsBora Derin
Department of Metallurgical and Materials Engineering, Istanbul Technical University, Istanbul, Turkey
2 shared publicationsMahmut Sami Alkan
2 shared publications
Latest Publications
- Open Access
Hydrometallurgical Recovery and Sorption Behavior of Rare Earth Elements from Terra Rossa Deposits: Evidence from the Seydişehir–Akseki Region (Türkiye)
Terra rossa (red soils) developed over carbonate terrains represent an unconventional yet potentially valuable secondary source of rare earth elements (REEs) due to enrichment in Fe–Al-rich weathering products. In this study, the hydrometallurgical recovery of REEs from terra rossa samples collected from the Seydişehir–Akseki region (Türkiye) was systematically investigated through acid leaching. Sulfuric acid (H2SO4), hydrochloric acid (HCl), and nitric acid (HNO3) were comparatively evaluated as lixiviants under optimized conditions. A Taguchi L16 orthogonal experimental design was used to assess the effects of acid concentration (1–4 M), temperature (25–95 °C), leaching duration (60–480 min), and solid-to-liquid ratio (1:10–1:40). All three acids achieved high REE recoveries under optimized conditions (4 M, 95 °C, 480 min, and 1:40 S/L). HCl exhibited the highest overall efficiency, yielding recoveries of 93–98%, followed by H2SO4 (89–96%) and HNO3 (88–97%). Statistical analyses indicated that acid type and concentration were the main factors controlling REE dissolution, followed by temperature and leaching duration. Overall, the results confirm that terra rossa deposits constitute an underexplored secondary REE resource and demonstrate that optimized acid leaching is an effective approach for the valorization of weathering-derived materials.
Open AccessHydrometallurgical Recovery and Sorption Behavior of Rare Earth Elements from Terra Rossa Deposits: Evidence from the Seydişehir–Akseki Region (Türkiye)
Terra rossa (red soils) developed over carbonate terrains represent an unconventional yet potentially valuable secondary source of rare earth elements (REEs) due to enrichment in Fe–Al-rich weathering products. In this study, the hydrometallurgical recovery of REEs from terra rossa samples collected from the Seydişehir–Akseki region (Türkiye) was systematically investigated through acid leaching. Sulfuric acid (H2SO4), hydrochloric acid (HCl), and nitric acid (HNO3) were comparatively evaluated as lixiviants under optimized conditions. A Taguchi L16 orthogonal experimental design was used to assess the effects of acid concentration (1–4 M), temperature (25–95 °C), leaching duration (60–480 min), and solid-to-liquid ratio (1:10–1:40). All three acids achieved high REE recoveries under optimized conditions (4 M, 95 °C, 480 min, and 1:40 S/L). HCl exhibited the highest overall efficiency, yielding recoveries of 93–98%, followed by H2SO4 (89–96%) and HNO3 (88–97%). Statistical analyses indicated that acid type and concentration were the main factors controlling REE dissolution, followed by temperature and leaching duration. Overall, the results confirm that terra rossa deposits constitute an underexplored secondary REE resource and demonstrate that optimized acid leaching is an effective approach for the valorization of weathering-derived materials.
- 25 April 2026
- Published by Taylor & Francis in Canadian Metallurgical Quarterly
- p. 1-15
Optimization of acid leaching for rare earth element recovery from red mud using the taguchi method
- 25 April 2026
- Published by Taylor & Francis in Canadian Metallurgical Quarterly
- p. 1-15
Optimization of acid leaching for rare earth element recovery from red mud using the taguchi method
- Open Access
- 19 February 2026
- Published by Springer Nature in JOM
- Vol. 78 (9) , 8305-8323
Selection of Mineral Acids for Extraction of Rare Earth Elements and Critical Metals from Bauxite Ore Using the Taguchi Method
The recovery of rare earth elements (REEs) and critical metals (CRMs) is increasingly important because of the growing industrial demand and resource scarcity. Bauxite, the main source of aluminum, has significant potential for REEs and CRMs. Therefore, in this study, the recovery of these strategic elements from Doğankuzu bauxite (Seydişehir, Turkey) is investigated systematically and comprehensively using three mineral acids (HCl, H 2 SO 4 , HNO 3 ). Seydişehir bauxite samples were subjected to direct mineral acids leaching to investigate the effects of acid concentration, temperature, solid-to-liquid ratio, and leaching time on the extraction efficiency of valuable metals. Process optimization was performed using the Taguchi method, identifying the optimal conditions for maximizing REE and CRM recoveries while minimizing the reagent consumption for each acid. Although individual optimum conditions varied by element, the common optimum conditions (4 M acid, 95°C, 480 min, solid-to-liquid ratio: 1/30 g/mL) provided a consistent basis for comparison. Under optimized conditions, La, Nd, and Pr achieved recoveries > 97% across all systems. Nitric acid generally exhibited a slightly higher recovery rate than other acids for most REEs. The highest recovery for Sc was achieved by sulfuric acid (82%), followed by hydrochloric acid (76%), whereas nitric acid (66%) was comparatively less effective under optimum conditons. In addition, Y remained below 55%, 54%, and 46% for nitric, sulfuric, and hydrochloric acid, respectively. Solubility of major oxides (Al 2 O 3 , SiO 2 , TiO 2 ) is more limited (< 30%) in all lixiviants because of incomplete dissolution of refractory phases, while Fe 2 O 3 has high solubility (~ 95%) in HCl and H 2 SO 4 . The ANOVA-based contribution analysis supports that temperature is the primary driver of REE recovery across all investigated systems, whereas other operational parameters exert only minor and secondary effects. These findings demonstrate the feasibility of bauxite leaching for REE/CRM extraction and highlight its potential integration into alumina production, providing a dual recovery strategy that enhances resource efficiency and supports sustainable supply chains.
- 19 February 2026
- Published by Springer Nature in JOM
- Vol. 78 (9) , 8305-8323
Open AccessSelection of Mineral Acids for Extraction of Rare Earth Elements and Critical Metals from Bauxite Ore Using the Taguchi Method
The recovery of rare earth elements (REEs) and critical metals (CRMs) is increasingly important because of the growing industrial demand and resource scarcity. Bauxite, the main source of aluminum, has significant potential for REEs and CRMs. Therefore, in this study, the recovery of these strategic elements from Doğankuzu bauxite (Seydişehir, Turkey) is investigated systematically and comprehensively using three mineral acids (HCl, H 2 SO 4 , HNO 3 ). Seydişehir bauxite samples were subjected to direct mineral acids leaching to investigate the effects of acid concentration, temperature, solid-to-liquid ratio, and leaching time on the extraction efficiency of valuable metals. Process optimization was performed using the Taguchi method, identifying the optimal conditions for maximizing REE and CRM recoveries while minimizing the reagent consumption for each acid. Although individual optimum conditions varied by element, the common optimum conditions (4 M acid, 95°C, 480 min, solid-to-liquid ratio: 1/30 g/mL) provided a consistent basis for comparison. Under optimized conditions, La, Nd, and Pr achieved recoveries > 97% across all systems. Nitric acid generally exhibited a slightly higher recovery rate than other acids for most REEs. The highest recovery for Sc was achieved by sulfuric acid (82%), followed by hydrochloric acid (76%), whereas nitric acid (66%) was comparatively less effective under optimum conditons. In addition, Y remained below 55%, 54%, and 46% for nitric, sulfuric, and hydrochloric acid, respectively. Solubility of major oxides (Al 2 O 3 , SiO 2 , TiO 2 ) is more limited (< 30%) in all lixiviants because of incomplete dissolution of refractory phases, while Fe 2 O 3 has high solubility (~ 95%) in HCl and H 2 SO 4 . The ANOVA-based contribution analysis supports that temperature is the primary driver of REE recovery across all investigated systems, whereas other operational parameters exert only minor and secondary effects. These findings demonstrate the feasibility of bauxite leaching for REE/CRM extraction and highlight its potential integration into alumina production, providing a dual recovery strategy that enhances resource efficiency and supports sustainable supply chains.
- 20 November 2025
- Published by Elsevier in Minerals Engineering
- Vol. 236
Extraction of critical elements from red mud as polymetallic source by solvometallurgical method
- 20 November 2025
- Published by Elsevier in Minerals Engineering
- Vol. 236
Extraction of critical elements from red mud as polymetallic source by solvometallurgical method
- 18 October 2025
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 42 (6) , 4085-4102
Comparison of Rare Earth Elements Recovery from Red Mud by Two Different Roasting-Leaching Methods: A Case Study of Seydişehir, Türkiye
- 18 October 2025
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 42 (6) , 4085-4102
Comparison of Rare Earth Elements Recovery from Red Mud by Two Different Roasting-Leaching Methods: A Case Study of Seydişehir, Türkiye
- 8 September 2025
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 11 (4) , 4256-4271
Solvometallurgical Recovery of Zinc and Lead from Çin–Kur Leaching Residue Using Deep Eutectic Solvent
- 8 September 2025
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 11 (4) , 4256-4271
Solvometallurgical Recovery of Zinc and Lead from Çin–Kur Leaching Residue Using Deep Eutectic Solvent
- 21 July 2022
- Published by Springer Nature
- p. 100-109
A Sample Study for Determining Energy Consumption Values in Public Buildings: Central Anatolia Region
- 21 July 2022
- Published by Springer Nature
- p. 100-109
A Sample Study for Determining Energy Consumption Values in Public Buildings: Central Anatolia Region
- 1 November 2021
- Published by Elsevier in Hydrometallurgy
- Vol. 205, 105732
Processing of anode slime with deep eutectic solvents as a green leachant
- 1 November 2021
- Published by Elsevier in Hydrometallurgy
- Vol. 205, 105732
Processing of anode slime with deep eutectic solvents as a green leachant
- 10 May 2021
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 36 (1) , 105-120
Bakır Anot Çamurundan Bakırın Liçinde Düşük Ötektik Noktalı Çözücü Kullanımının Araştırılması
Bu çalışmada, pirometalurjik yöntemle metalik bakır üretiminin elektrokazanım aşamasında ortaya çıkan anot çamurundan bakır geri kazanımı üzerine çevre ve insan sağlığına duyarlı düşük ötektik noktalı çözücü (DES) kullanımı araştırılmıştır. Taguchi optimizasyon yöntemi kullanılarak liç sıcaklığı, liç süresi ve katı/sıvı oranı deneysel parametrelerin bakır geri kazanımı üzerine etkisi incelenmiştir. Kolin klorür (ChCl) ve ürenin 1:2 molar oranda karıştırılmasıyla hazırlanan DES çözücüsü ile yapılan liç işlemleri sonunda optimum şartlar; 95 oC’liç sıcaklığı, 2 saat liç süresi ve 1/20 katı/sıvı oranı olarak belirlenmiş ve bu şartlarda %98 bakır geri kazanımı elde edilmiştir. Yapılan bu çalışma ile ChCl-üre karışımıyla hazırlanan DES çözücüsünün anot çamurundan bakır geri kazanımı için çevreci bir çözücü adayı olabileceği ortaya konulmuştur.
- 10 May 2021
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 36 (1) , 105-120
Bakır Anot Çamurundan Bakırın Liçinde Düşük Ötektik Noktalı Çözücü Kullanımının Araştırılması
Bu çalışmada, pirometalurjik yöntemle metalik bakır üretiminin elektrokazanım aşamasında ortaya çıkan anot çamurundan bakır geri kazanımı üzerine çevre ve insan sağlığına duyarlı düşük ötektik noktalı çözücü (DES) kullanımı araştırılmıştır. Taguchi optimizasyon yöntemi kullanılarak liç sıcaklığı, liç süresi ve katı/sıvı oranı deneysel parametrelerin bakır geri kazanımı üzerine etkisi incelenmiştir. Kolin klorür (ChCl) ve ürenin 1:2 molar oranda karıştırılmasıyla hazırlanan DES çözücüsü ile yapılan liç işlemleri sonunda optimum şartlar; 95 oC’liç sıcaklığı, 2 saat liç süresi ve 1/20 katı/sıvı oranı olarak belirlenmiş ve bu şartlarda %98 bakır geri kazanımı elde edilmiştir. Yapılan bu çalışma ile ChCl-üre karışımıyla hazırlanan DES çözücüsünün anot çamurundan bakır geri kazanımı için çevreci bir çözücü adayı olabileceği ortaya konulmuştur.
- 31 December 2020
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 28 (3) , 308-320
INVESTIGATION OF USE OF DEEP EUTETIC SOLVENT ON COPPER RECOVERY FROM COPPER ANODE SLAG
Bu çalışmada, ikincil kaynaklardan bakır tel üretimi yapan bir firmadan temin edilen bakır anot cürufundan bakır geri kazanımı için çevre ve insan sağlığına duyarlı düşük erime noktalı çözücü kullanımı araştırılmıştır. Bakır anot cürufunun fiziksel, kimyasal ve mineralojik karakterizasyonu öncesinde yapılan öğütme işleminde cüruf içindeki metalik bakırın bir kısmı fiziksel olarak ayrılmıştır. Liç deneylerinde son yıllarda hidrometalurjik süreçlerde kullanılan kolin klorür (ChCl) ve üre (1:2) ile hazırlanan düşük erime noktalı solvent çevre duyarlı çözücü olarak kullanılmıştır. Liç deneylerinin sonuçlarına göre fiziksel olarak anot cürufundan ayrılmayan bakır 72 saatlik reaksiyon süresi, 95 oC’lik liç sıcaklığı ve 1/20 katı/sıvı oranı şartlarındaki liç işlemi ile %90 üzerinde ekstrakte edilmiştir. Liç deneylerinden sonrasında çözeltideki demir çözünürlüğünün oldukça düşük seviyede kaldığı görülmüştür. Çalışmada elde edilen sonuçlara göre fiziksel olarak ayırma ve sonrasında ChCl-üre karışımıyla hazırlanan düşük erime noktalı çözücü kullanılarak yapılan liç işlemleri ile bakır anot cürufundan bakır geri kazanımı için çevreci bir çözücü adayı olabileceği ortaya konmuştur.
- 31 December 2020
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 28 (3) , 308-320
INVESTIGATION OF USE OF DEEP EUTETIC SOLVENT ON COPPER RECOVERY FROM COPPER ANODE SLAG
Bu çalışmada, ikincil kaynaklardan bakır tel üretimi yapan bir firmadan temin edilen bakır anot cürufundan bakır geri kazanımı için çevre ve insan sağlığına duyarlı düşük erime noktalı çözücü kullanımı araştırılmıştır. Bakır anot cürufunun fiziksel, kimyasal ve mineralojik karakterizasyonu öncesinde yapılan öğütme işleminde cüruf içindeki metalik bakırın bir kısmı fiziksel olarak ayrılmıştır. Liç deneylerinde son yıllarda hidrometalurjik süreçlerde kullanılan kolin klorür (ChCl) ve üre (1:2) ile hazırlanan düşük erime noktalı solvent çevre duyarlı çözücü olarak kullanılmıştır. Liç deneylerinin sonuçlarına göre fiziksel olarak anot cürufundan ayrılmayan bakır 72 saatlik reaksiyon süresi, 95 oC’lik liç sıcaklığı ve 1/20 katı/sıvı oranı şartlarındaki liç işlemi ile %90 üzerinde ekstrakte edilmiştir. Liç deneylerinden sonrasında çözeltideki demir çözünürlüğünün oldukça düşük seviyede kaldığı görülmüştür. Çalışmada elde edilen sonuçlara göre fiziksel olarak ayırma ve sonrasında ChCl-üre karışımıyla hazırlanan düşük erime noktalı çözücü kullanılarak yapılan liç işlemleri ile bakır anot cürufundan bakır geri kazanımı için çevreci bir çözücü adayı olabileceği ortaya konmuştur.