John Young
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
John Young has a total of 121 co-authors. Here are the top co-authors by number of shared publications:
- Joseph C. S. Lai
School of Engineering and Technology, University of New South Wales, Canberra, ACT 2600, Australia
58 shared publications - Fang-Bao Tian
University of New South Wales
33 shared publications - Li Wang
National Computational Infrastructure, The Australian National University, Canberra, ACT 2600, Australia
11 shared publications - Max F. Platzer
AeroHydro Research & Technology Associates
11 shared publications Fang-Bao Tian
School of Engineering and Technology, University of New South Wales, Canberra, Australia
9 shared publications- Sridhar Ravi
School of Engineering and Technology, University of New South Wales
8 shared publications
Latest Publications
- Open Access
- 6 May 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1034
A predictive framework for energy harvesting based on four canonical modes of vortex–foil interaction
This work presents a predictive framework for energy harvesting of two tandem and staggered flapping foils based on four canonical modes of vortex–foil interaction. The role of the incoming vortex generated by the leading foil in modulating the hydrodynamic load of the trailing foil is systematically analysed. Four canonical interaction modes are classified by the vortex rotation and its interaction position relative to the leading-edge vortex (LEV). The most effective configuration occurs when the foil encounters a counter-rotating vortex on the pressure side, which strengthens the LEV and consequently enhances the lift magnitude, with maximum efficiency achieved when vortex merging occurs near stroke reversal. A second constructive mode occurs when a co-rotating vortex on the suction side promotes LEV roll-up through favourable induced velocities. Force decomposition reveals that in both constructive modes, the incoming vortices improve the efficiency of the trailing foil by enhancing the unsteady lift through altering the local velocity to strengthen the LEV or promote its roll-up, while their low-pressure cores contribute marginally to the unsteady force. Two destructive modes are also observed: direct interaction of a counter-rotating vortex on the suction side leads to only a transient lift increase; a co-rotating vortex on the pressure side reduces the effective angle of attack and leads to the poorest performance. Building on these insights, a mechanism-based predictive framework is established to rapidly identify high-performance configurations without exhaustive parametric exploration. The framework applies broadly to different wake conditions and trailing-foil kinematics and guides the design of multi-foil energy-harvesting systems.
- 6 May 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1034
Open AccessA predictive framework for energy harvesting based on four canonical modes of vortex–foil interaction
This work presents a predictive framework for energy harvesting of two tandem and staggered flapping foils based on four canonical modes of vortex–foil interaction. The role of the incoming vortex generated by the leading foil in modulating the hydrodynamic load of the trailing foil is systematically analysed. Four canonical interaction modes are classified by the vortex rotation and its interaction position relative to the leading-edge vortex (LEV). The most effective configuration occurs when the foil encounters a counter-rotating vortex on the pressure side, which strengthens the LEV and consequently enhances the lift magnitude, with maximum efficiency achieved when vortex merging occurs near stroke reversal. A second constructive mode occurs when a co-rotating vortex on the suction side promotes LEV roll-up through favourable induced velocities. Force decomposition reveals that in both constructive modes, the incoming vortices improve the efficiency of the trailing foil by enhancing the unsteady lift through altering the local velocity to strengthen the LEV or promote its roll-up, while their low-pressure cores contribute marginally to the unsteady force. Two destructive modes are also observed: direct interaction of a counter-rotating vortex on the suction side leads to only a transient lift increase; a co-rotating vortex on the pressure side reduces the effective angle of attack and leads to the poorest performance. Building on these insights, a mechanism-based predictive framework is established to rapidly identify high-performance configurations without exhaustive parametric exploration. The framework applies broadly to different wake conditions and trailing-foil kinematics and guides the design of multi-foil energy-harvesting systems.
- Open Access
- 3 March 2026
- Published by MDPI AG in Technologies
- Vol. 14 (3) , 155
Predicting Technological Trends and Effects Enabling Large-Scale Supply Drones
Drones have long been explored by commercial and military users for supply. While several systems offering small payloads in drone delivery have seen operational use, large-scale supply drones have yet to be adopted. A range of setbacks cause this, including technological and operational challenges that hinder their adoption. Here, we evaluate these challenges from a conceptual modelling perspective and forecast their applicability once these barriers are overcome. This study uses technology trend modelling and bibliometric activity mapping methodologies to predict the applicability of specific technologies that are currently identified as operational challenges. Specifically for supply drones, we model trends in technological improvements of battery technology and aircraft control, and project its focus on landing zone autonomy and powertrain. The prediction also focuses on the current state of hybrid power and higher levels of automation required for landing zone operations. These models are validated through several published case studies of small delivery drones and then applied to assess the feasibility and constraints of larger supply drones. A case study involving the conceptual design of a supply drone large enough to move a shipping container is presented to illustrate the critical technologies required to transition large supply drones from concept to operational reality. Key technologies required for large-scale supply drones have yet to build up a critical mass of research activity, particularly on landing zone autonomy and powertrain. Moreover, additional constraints beyond technological and operational challenges could include limitations in autonomy, certification hurdles, regulatory complexity, and the need for greater social trust and acceptance.
- 3 March 2026
- Published by MDPI AG in Technologies
- Vol. 14 (3) , 155
Open AccessPredicting Technological Trends and Effects Enabling Large-Scale Supply Drones
Drones have long been explored by commercial and military users for supply. While several systems offering small payloads in drone delivery have seen operational use, large-scale supply drones have yet to be adopted. A range of setbacks cause this, including technological and operational challenges that hinder their adoption. Here, we evaluate these challenges from a conceptual modelling perspective and forecast their applicability once these barriers are overcome. This study uses technology trend modelling and bibliometric activity mapping methodologies to predict the applicability of specific technologies that are currently identified as operational challenges. Specifically for supply drones, we model trends in technological improvements of battery technology and aircraft control, and project its focus on landing zone autonomy and powertrain. The prediction also focuses on the current state of hybrid power and higher levels of automation required for landing zone operations. These models are validated through several published case studies of small delivery drones and then applied to assess the feasibility and constraints of larger supply drones. A case study involving the conceptual design of a supply drone large enough to move a shipping container is presented to illustrate the critical technologies required to transition large supply drones from concept to operational reality. Key technologies required for large-scale supply drones have yet to build up a critical mass of research activity, particularly on landing zone autonomy and powertrain. Moreover, additional constraints beyond technological and operational challenges could include limitations in autonomy, certification hurdles, regulatory complexity, and the need for greater social trust and acceptance.
- Open Access
- 2 March 2026
- Published by Elsevier in Journal of Fluids and Structures
- Vol. 143
A comparison of rotating and flapping wings in highly compressible flows
- 2 March 2026
- Published by Elsevier in Journal of Fluids and Structures
- Vol. 143
Open AccessA comparison of rotating and flapping wings in highly compressible flows
- Open Access
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Buckling of three-dimensional wavy collapsible tubes conveying viscous flows
This study investigates the buckling behaviors of wavy collapsible tubes conveying viscous flows using the immersed boundary-lattice Boltzmann method, with focus on the effect of several key parameters (including external pressure, bending rigidity, and wave number) on the deformation patterns and buckling behaviors. The results show that the higher circumferential modes occur when the bending stiffness decreases and/or the external pressure increases, as observed in straight tubes. The transition from mode-2 to mode-3 occurs earlier for the nw=1.5 case than the straight tube, even though the effective stiffness of the tube decreases when the wave number decreases with nw=0 corresponding to the straight tubes. This is due to the minimum fluid pressure at the lowest point of the wavy wall. The transition to mode-4 occurs earlier in the straight tube, highlighting the predominant effect of stiffness. Compared to the symmetric mode-2 in the straight tube, an asymmetric mode-2 is observed in the wavy tube (nw=1.5) due to the asymmetric flow structure and fluid–structure interactions. In addition, two distinct flow patterns are observed: the shell-based and the finger-shaped structures. Finally, a buckling analysis on the structure only shows that the critical buckling stress increases with the wave number, as demonstrated by a modification of the available analytical formulation for critical buckling.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Open AccessBuckling of three-dimensional wavy collapsible tubes conveying viscous flows
This study investigates the buckling behaviors of wavy collapsible tubes conveying viscous flows using the immersed boundary-lattice Boltzmann method, with focus on the effect of several key parameters (including external pressure, bending rigidity, and wave number) on the deformation patterns and buckling behaviors. The results show that the higher circumferential modes occur when the bending stiffness decreases and/or the external pressure increases, as observed in straight tubes. The transition from mode-2 to mode-3 occurs earlier for the nw=1.5 case than the straight tube, even though the effective stiffness of the tube decreases when the wave number decreases with nw=0 corresponding to the straight tubes. This is due to the minimum fluid pressure at the lowest point of the wavy wall. The transition to mode-4 occurs earlier in the straight tube, highlighting the predominant effect of stiffness. Compared to the symmetric mode-2 in the straight tube, an asymmetric mode-2 is observed in the wavy tube (nw=1.5) due to the asymmetric flow structure and fluid–structure interactions. In addition, two distinct flow patterns are observed: the shell-based and the finger-shaped structures. Finally, a buckling analysis on the structure only shows that the critical buckling stress increases with the wave number, as demonstrated by a modification of the available analytical formulation for critical buckling.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Propeller blade performance in low-pressure environments
There have been increasing applications of propeller-driven flyers in non-Earth environments where significantly lower ambient pressures are present. This work experimentally studies the performance of rotor propeller blades of an airfoil profile in low-pressure environments by varying the aspect ratio ( ), angle of attack (α), and rotational speed of the blade. The experiments are performed in a vacuum chamber to investigate performance at various ambient pressures ranging from 3 to 96 kPa, resulting in a Reynolds number range of 300–27 500. Thrust and torque on a two-blade rotor are measured. The thrust (CT) and power (CP) coefficients of the propeller increased with α and [ ] while they were not influenced by ambient pressure levels, except for the lowest pressure tested here (3 kPa). The thrust to power ratio (CT/CP), however, decreases with the ambient pressure and α, suggesting a reduction in performance. At lower ambient pressures (<16 kPa), both CT/CP and figure of merit are higher for blades operating at higher angles of attack and lower . This increase in performance of lower rotors at high α can likely be attributed to low Reynolds number effects, which play a significant role at lower ambient pressures. These findings highlight the significant variations in performance due to reduced ambient pressures and will be useful for understanding the design requirements based on the aerodynamic performance of propellers in extraterrestrial environments.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Propeller blade performance in low-pressure environments
There have been increasing applications of propeller-driven flyers in non-Earth environments where significantly lower ambient pressures are present. This work experimentally studies the performance of rotor propeller blades of an airfoil profile in low-pressure environments by varying the aspect ratio ( ), angle of attack (α), and rotational speed of the blade. The experiments are performed in a vacuum chamber to investigate performance at various ambient pressures ranging from 3 to 96 kPa, resulting in a Reynolds number range of 300–27 500. Thrust and torque on a two-blade rotor are measured. The thrust (CT) and power (CP) coefficients of the propeller increased with α and [ ] while they were not influenced by ambient pressure levels, except for the lowest pressure tested here (3 kPa). The thrust to power ratio (CT/CP), however, decreases with the ambient pressure and α, suggesting a reduction in performance. At lower ambient pressures (<16 kPa), both CT/CP and figure of merit are higher for blades operating at higher angles of attack and lower . This increase in performance of lower rotors at high α can likely be attributed to low Reynolds number effects, which play a significant role at lower ambient pressures. These findings highlight the significant variations in performance due to reduced ambient pressures and will be useful for understanding the design requirements based on the aerodynamic performance of propellers in extraterrestrial environments.
- Open Access
- 22 December 2025
- Published by MDPI AG in Preprints.org
Predicting Technological Trends and Effects Enabling Large-Scale Supply Drones
Drones have long been explored for supply. While several systems offering small pay-loads in drone delivery have seen operational use, large-scale supply drones have yet to be adopted. A range of setbacks cause this, including technological and operational challenges that hinder their adoption. Here, these challenges are evaluated from a conceptual modelling perspective to forecast their applicability once these barriers are overcome. The study uses technology trend modelling and bibliometric activity map-ping methodologies to predict the applicability of specific technologies that are cur-rently identified as operational challenges. Specifically for supply drones, trends in technological improvements of battery technology and aircraft control are modelled to project effects and focus on landing zone autonomy and powertrain. The prediction also focuses on the current state of hybrid power and higher levels of automation required for landing zone operations. These models are validated through several published case studies of small delivery drones and then applied to assess the feasibility and con-straints of larger supply drones. A case study, conceptual design of a supply drone large enough to move a shipping container, is presented to illustrate the critical technologies required to transition large supply drones from concept to operational reality. Key technologies required for large-scale supply drones have yet to build up a critical mass of research activity, particularly on landing zone autonomy and powertrain. Moreover, additional constraints beyond technological and operational challenges could include limitations in autonomy, certification hurdles, regulatory complexity, and the need for greater social trust and acceptance.
- 22 December 2025
- Published by MDPI AG in Preprints.org
Open AccessPredicting Technological Trends and Effects Enabling Large-Scale Supply Drones
Drones have long been explored for supply. While several systems offering small pay-loads in drone delivery have seen operational use, large-scale supply drones have yet to be adopted. A range of setbacks cause this, including technological and operational challenges that hinder their adoption. Here, these challenges are evaluated from a conceptual modelling perspective to forecast their applicability once these barriers are overcome. The study uses technology trend modelling and bibliometric activity map-ping methodologies to predict the applicability of specific technologies that are cur-rently identified as operational challenges. Specifically for supply drones, trends in technological improvements of battery technology and aircraft control are modelled to project effects and focus on landing zone autonomy and powertrain. The prediction also focuses on the current state of hybrid power and higher levels of automation required for landing zone operations. These models are validated through several published case studies of small delivery drones and then applied to assess the feasibility and con-straints of larger supply drones. A case study, conceptual design of a supply drone large enough to move a shipping container, is presented to illustrate the critical technologies required to transition large supply drones from concept to operational reality. Key technologies required for large-scale supply drones have yet to build up a critical mass of research activity, particularly on landing zone autonomy and powertrain. Moreover, additional constraints beyond technological and operational challenges could include limitations in autonomy, certification hurdles, regulatory complexity, and the need for greater social trust and acceptance.
- 3 November 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1022, A28
Lift increment scaling and its failure due to the leading-edge vortex detachment transition for a flapping wing under perturbations
A heaving and pitching wing encountering effective angle-of-attack perturbations at the Reynolds numbers of 2000 and 20 000 is numerically studied by using an immersed boundary–lattice Boltzmann method. The perturbations are introduced as an abrupt heaving or pitching motion superposed on the baseline motion. It is found that the lift increment scales with the increase in the perturbation effective angle of attack, especially during the heaving perturbation. The pitching perturbation is more likely to disrupt this scaling due to the transition of the leading-edge vortex (LEV) detachment mechanism, where the detachment mechanism of the LEV transitions from bluff-body shedding dominant to vorticity layer eruption dominant. Despite the same variation in the effective angle of attack for the heaving and pitching perturbations, vorticity layer eruption is more likely to occur under the fast pitching perturbation. When the Reynolds number is increased to 20 000, the time histories of aerodynamic force are similar to those at the Reynolds number of 2000. Moreover, the boundary layer under the LEV is more resistant to the adverse pressure gradient, leading to greater variability in vorticity layer eruption.
- 3 November 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1022, A28
Lift increment scaling and its failure due to the leading-edge vortex detachment transition for a flapping wing under perturbations
A heaving and pitching wing encountering effective angle-of-attack perturbations at the Reynolds numbers of 2000 and 20 000 is numerically studied by using an immersed boundary–lattice Boltzmann method. The perturbations are introduced as an abrupt heaving or pitching motion superposed on the baseline motion. It is found that the lift increment scales with the increase in the perturbation effective angle of attack, especially during the heaving perturbation. The pitching perturbation is more likely to disrupt this scaling due to the transition of the leading-edge vortex (LEV) detachment mechanism, where the detachment mechanism of the LEV transitions from bluff-body shedding dominant to vorticity layer eruption dominant. Despite the same variation in the effective angle of attack for the heaving and pitching perturbations, vorticity layer eruption is more likely to occur under the fast pitching perturbation. When the Reynolds number is increased to 20 000, the time histories of aerodynamic force are similar to those at the Reynolds number of 2000. Moreover, the boundary layer under the LEV is more resistant to the adverse pressure gradient, leading to greater variability in vorticity layer eruption.
- Open Access
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
The aerodynamic and acoustic performance of a bumblebee-inspired micro-air vehicle in Martian atmosphere
Micro-air vehicles (MAVs) based on flapping wings have been identified as a potential means for Mars exploration due to their high performance in low-Reynolds-number environments. The low-density atmosphere on Mars and the small scales of MAVs impose challenges in their operation due to rarefaction and compressibility effects. This study numerically investigates the aerodynamic and acoustic performance of a bumblebee-inspired MAV in compressible, rarefied flows. To decouple the effects of rarefaction and compressibility, the average wingtip Mach number (Ma) varies from 0.6 to 1.4, and the Knudsen number (Kn) varies from 0 to 0.05 with a second-order slip model implemented for Kn≥0.01. The numerical results show that rarefaction offers an improvement in the lift coefficient mainly attributed to a decrease in the viscous force, while the increase in Mach number results in a lift reduction due to the pressure variations. The introduction of the slip boundary results in some minor changes in pressure forces due to a change in the formation and development of the vortex structures at the leading edge of the wing. Acoustic signatures are a function of Ma due to the appearance, propagation, and interaction of shock waves. The variation in shock strength results in an increase in sound pressure, while the shock shape and shock interactions during stroke reversal phases result in the shift of the secondary harmonic frequency profile from a quad-pole source at Ma=0.6 to a hex-pole source at Ma=1.4.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Open AccessThe aerodynamic and acoustic performance of a bumblebee-inspired micro-air vehicle in Martian atmosphere
Micro-air vehicles (MAVs) based on flapping wings have been identified as a potential means for Mars exploration due to their high performance in low-Reynolds-number environments. The low-density atmosphere on Mars and the small scales of MAVs impose challenges in their operation due to rarefaction and compressibility effects. This study numerically investigates the aerodynamic and acoustic performance of a bumblebee-inspired MAV in compressible, rarefied flows. To decouple the effects of rarefaction and compressibility, the average wingtip Mach number (Ma) varies from 0.6 to 1.4, and the Knudsen number (Kn) varies from 0 to 0.05 with a second-order slip model implemented for Kn≥0.01. The numerical results show that rarefaction offers an improvement in the lift coefficient mainly attributed to a decrease in the viscous force, while the increase in Mach number results in a lift reduction due to the pressure variations. The introduction of the slip boundary results in some minor changes in pressure forces due to a change in the formation and development of the vortex structures at the leading edge of the wing. Acoustic signatures are a function of Ma due to the appearance, propagation, and interaction of shock waves. The variation in shock strength results in an increase in sound pressure, while the shock shape and shock interactions during stroke reversal phases result in the shift of the secondary harmonic frequency profile from a quad-pole source at Ma=0.6 to a hex-pole source at Ma=1.4.
- Open Access
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Effects of confined boundaries on hovering flight using the unsteady vortex lattice method
Insect flight adjacent to single or multiple walls during hovering or approaching perching is common in nature. The aerodynamic forces of insects flying near multiple surfaces may deviate significantly from those experienced during normal hover over a single ground. This work investigates the effects of multiple walls on a three-dimensional hovering wing. The aerodynamics of the hovering wing is calculated by the unsteady vortex lattice method (UVLM). To handle the flow instabilities associated with strong wing-wake and wake-wake interactions in hover, a novel treatment of wake straining is incorporated with a vortex core growth model that stabilizes the numerical simulation and avoid numerical dispersion. The treatment significantly extends the capability of the UVLM and improves its accuracy in the modeling of wings during hovering flight. The ground effects are modeled by a lattice of bound vortices. To study the effects of multiple walls, two cases are considered: a pair of hovering wings in a U-shaped channel and between top and bottom walls. The lift coefficients and the flow fields are analyzed by varying the distance between the wing and the walls. Three typical regimes are identified due to the walls: force enhancement, force reduction and force recovery. The lift coefficient of the wing in the U-shaped channel is lower than the wing hovering over a single ground, while that of the wing between the top and the bottom walls is higher. These observations are closely related to the changes in wake and vortex structures causing changes in the downwash and effective angle of attack of the wing.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Open AccessEffects of confined boundaries on hovering flight using the unsteady vortex lattice method
Insect flight adjacent to single or multiple walls during hovering or approaching perching is common in nature. The aerodynamic forces of insects flying near multiple surfaces may deviate significantly from those experienced during normal hover over a single ground. This work investigates the effects of multiple walls on a three-dimensional hovering wing. The aerodynamics of the hovering wing is calculated by the unsteady vortex lattice method (UVLM). To handle the flow instabilities associated with strong wing-wake and wake-wake interactions in hover, a novel treatment of wake straining is incorporated with a vortex core growth model that stabilizes the numerical simulation and avoid numerical dispersion. The treatment significantly extends the capability of the UVLM and improves its accuracy in the modeling of wings during hovering flight. The ground effects are modeled by a lattice of bound vortices. To study the effects of multiple walls, two cases are considered: a pair of hovering wings in a U-shaped channel and between top and bottom walls. The lift coefficients and the flow fields are analyzed by varying the distance between the wing and the walls. Three typical regimes are identified due to the walls: force enhancement, force reduction and force recovery. The lift coefficient of the wing in the U-shaped channel is lower than the wing hovering over a single ground, while that of the wing between the top and the bottom walls is higher. These observations are closely related to the changes in wake and vortex structures causing changes in the downwash and effective angle of attack of the wing.