TZTiberiu-Gabriel Zsurzsan

Tiberiu-Gabriel Zsurzsan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tiberiu-Gabriel Zsurzsan has a total of 59 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Three-Dimensional Interconnect LLC-DCX Converter for Datacenter Application

    by Pinhe Wang, Bima Nugraha Sanusi, Tiberiu-Gabriel Zsurzsan, Michael A. E. Andersen, Ziwei Ouyang

    Driven by substantial amount of electricity consumption in datacenters, the demand for efficient power management has led to the adoption of the 48 V bus power distribution system. To deliver the required high current to xPUs, the unregulated intermediate bus converter (IBC) is typically needed to step down the 48 V bus voltage. For high power density and high efficiency, this article proposes a three-dimensional interconnect LLC-DCX converter with 8:1 voltage ratio as the unregulated IBC. Two different winding configurations and their corresponding operation modes, diagonal operation mode (DOM) and same-side operation mode (SOM), are presented. DOM enables higher leakage inductance and winding resistance due to poor interleaving, but its overall ac resistance can be reduced by over 50% compared to SOM at the 550 kHz switching frequency due to much lower termination resistance. Finally, two prototypes using DOM and SOM configurations are implemented with similar circuit parameters. Experiment results indicate the prototype in DOM achieves higher power density and higher efficiency. The power density is 725 W/inch3 with 606 W maximum output power, and the peak efficiency is 96.3%. While, in SOM, the power density is 441 W/inch3 with 368 W maximum output power, and the peak efficiency is 94.1%.


  • 3D-Printed Conductance-Based Force Sensors Using Single Traxels

    by Anders Frem Wolstrup, Thomas Schlaikjer Holst, Jon Spangenberg, Tiberiu Gabriel Zsurzsan

    This study investigates the use of 3D printing for fabricating conductance-based force sensors with cellbased geometries. Three mathematically defined structures, sine wave, circle, and Reuleaux triangle, were implemented using single traxels (3D-printed conductive tracks) to maximize contact area and enabling consistent fabrication. The sensors were produced via Fused Deposition Modelling (FDM) and programmed using FullControl G-code, enabling direct translation of mathematical functions into print paths. The sine wave design achieved the highest sensitivity (0.035 N −1) and 95% linearity, consistent with constriction resistance theory. All designs demonstrated reliable performance with minimal process-induced variation. These findings highlight the potential of traxel-based 3D printing as a cost-effective and customizable approach for producing force sensors suited for applications in human-machine interfacing and soft robotics.

  • Open Access

    Design Automation Using Exclusion-Based Hierarchical Computation for Power Electronics Converters in Harsh Environments

    by Yudi Xiao, Zhe Zhang, Gabriel Zsurzsan, Michael A.E. Andersen, Martin MacFadyen, Yuchuan Liao, Rafael Pena Alzola, Weijia Yuan, Min Zhang

    Designing power electronics converters for harsh environments is challenging due to the absence of components' performance under harsh conditions, the frequent transition and data-passing among various software, and the time-consuming and computationally heavy work flow. This paper promotes using design automation to address the aforementioned design challenges. The implementations include public-accessible component databases, automated co-action among circuit simulators and finite element simulations to perform electrical, electromagnetic and thermal co-design, and finally an exclusionbased work flow with hierarchical computation to reduce computational load. The theorized framework is exemplified on designing a real world 175 ◦C 1.5kW Three-level Neutral-point-clamped dc-dc converter. A database containing the high-temperature characteristics of SiC MOSFETs and ferrites is established and shared through a web application with graphical user interface. In 310 min, the program, which includes computationally heavy 3D finite element simulation, delivers design output after evaluating the converter's electrical, electromagnetic and thermal performance under 10 million parameter sets. Finally, a 1.5kW dc-dc converter prototype is built and tested in 175 ◦C ambient temperature to verify the quality of the design output


  • Design Methodology of High Power Density Converter with Wide Input Voltage Range

    by Pinhe Wang, Tiberiu-Gabriel Zsurzsan, Michael A. E. Andersen, Ziwei Ouyang

    High-power density and high efficiency have always been the pursuit of power supplies. In the industry, the two-stage converter is widely employed in various applications for its inherent advantages, such as high reliability and simple control. In this article, the design methodology of high-power-density converters is given and presented for the two-stage converters systematically, including topology comparison, magnetic integration, and circuit parameters design. First, this article evaluates and compares three different topologies and the Boost-DCX configuration with low-component stress factors is selected. Then, to shrink the magnetic size, a matrix core is proposed to integrate two coupled inductors and one transformer. In comparison with the traditional magnetic design method using two E-I cores, the footprint of proposed core is reduced by around 30%. Finally, the proposed methodology is employed in a two-stage isolated converter for datacenter applications. A 1-kW prototype, from 38–72-V input to 53.5-V output, demonstrates a peak efficiency of 95.6% and a power density of 126 W/in 3 .


  • Utilizing Mutual Coupling to Eliminate Parasitic Inductance in EMI Filter Capacitors for Noise Reduction

    by Pinhe Wang, Bima Nugraha Sanusi, Chao Liu, Jiasheng Huang, Tiberiu-Gabriel Zsurzsan, Michael A. E. Andersen, Ziwei Ouyang

    Power devices based on wide-bandgap (WBG) semiconductor materials, like Silicon Carbide (SiC) and Gallium Nitride (GaN), have notably enhanced power conversion efficiency and power density. However, the fast-switching transient and high switching frequency have brought a significant electromagnetic interference (EMI) challenge within the high frequency (HF) range. And the HF performance of EMI filters is degraded by equivalent series inductance (ESL) of X- and Y-capacitors. In this article, a new and comprehensive model using mutual coupling is proposed to eliminate parasitic inductance for EMI filter capacitors. Based on the proposed model, nine different methods of ESL cancellation are derived. Meanwhile, in contrast to previous research, this work analyzes and compares different ESL cancellation methods. And due to the superiority of symmetrical configuration, it is recommended for ESL cancellation of X-capacitors. In the case studied, the ESL of the X-capacitor has been effectively eliminated up to 40 MHz. Consequently, the differential-mode (DM) noise of the active clamping flyback (ACF) converter exhibits a significant reduction from approximately 3.5 MHz to 30 MHz.


  • Pentacentra Transformer for Multiphase LLC Converter in High-Current Data Center Application

    by Chang Wang, Mingxiao Li, Ziwei Ouyang, Tiberiu-Gabriel Zsurzsan, Michael A.E. Andersen

    The role of data centers has become significant in the era of information technology, and their operation consumes a substantial amount of energy. Therefore, the point-of-load (POL) converter or voltage regulation module (VRM) used in data centers must have high efficiency and power density to deliver a large current to specific servers. A common bus voltage 48V at the rack stage needs to be stepped down to intermediate bus voltage, which is 6-5V in this case. To achieve this, a new pentacentra transformer was developed for a 4-phase LLC converter. A centra bar serving as the 5 th leg of the core is added to the conventional 4-leg matrix transformer. The interleaving and integration of windings in the proposed pentacentra transformer enabled balanced current sharing and reduced conduction loss by 45% compared to the traditional winding layout. The experimental prototype of the converter was designed to achieve 800 W power output at a switching frequency of 500 kHz and 48V-40V/6V-5V voltage conversion. The peak efficiency achieves 98.1% along with the power density of 240 W/in 3 with the experimental result. Without the heatsink, the whole converter is operating at rated power within a safe temperature lower than 86 °. The excellent thermal performance ensures the reliable operation of the converter and promises a larger power delivery capability.


  • AI-Based Design With Data Trimming for Hybrid Phase Shift Modulation for Minimum-Current-Stress Dual Active Bridge Converter

    by Fanfan Lin, Xin Zhang, Xinze Li, Changjiang Sun, Gabriel Zsurzsan, Wenjian Cai, Chang Wang

    Dual active bridge (DAB) topology has been recognized as the key circuit for the next generation of high-frequency-link power conversion systems. In order to realize desired operating performance, DAB modulation strategies need to be selected carefully. Different modulation strategies have been considered and combined into a hybrid one, which is able to fully optimize performance. However, to develop a hybrid modulation strategy, the conventional methods including harmonic model and piecewise model have difficulty in balancing modeling accuracy and manpower burden. Although recent data-driven modulation approaches can automate the design process, the accuracy of data-driven models decreases nontrivially with the existence of outliers and without sufficient data. Hence, to alleviate human-dependence and improve modeling accuracy, this paper proposes an AI-based design with data trimming (AI-DT) for hybrid phase shift modulation. Two two-degree-of-freedom modulation strategies are considered for the sake of optimal current stress performance. AI-DT firstly adopts the one-class support vector machine (SVM) to exclude outliers. Second, the state-of-the-art extreme gradient boosting (XGBoost), which is insensitive to training data size, is adopted to build data-driven current stress models for the DAB converter. After that, differential evolution (DE) algorithm helps to choose modulation strategy and optimize modulation parameters for optimal current stress. Generally, the proposed AI-DT is developed in an automated fashion, which largely relieves manual computational complexity while exhibiting satisfactory modulation accuracy. The effectiveness of the proposed AI-DT approach has been experimentally verified with a 1kW hardware prototype, realizing optimal current stress under full operating conditions with more than 96.5% as peak efficiency.


  • ZVS Design in Full-SiC Three-Level Neutral-Point-Clamped DC–DC Converter Considering Quasi-Linear Output Capacitance $C_{oss}$

    by Yudi Xiao, Martijn Sebastiaan Duraij, Zhe Zhang, Tiberiu-Gabriel Zsurzsan, Michael A. E. Andersen

    The Three-level Neutral-point-clamped (TLNPC) dc-dc converter is a popular topology for applications with high input voltage due to its simplicity of modulation, capability of withstanding high input voltage, and Zero-voltage-switching (ZVS) operation. Regarding mitigating the voltage ringing on secondary side, energy recovery approach is preferred to RCD approach for the sake of high efficiency and small component counts. This paper demonstrates that, using recovery approach in a Silicon Carbide (SiC) based TLNPC dc-dc converter causes hard-switching of the outer switches due to the quasi-linear output capacitance Coss of SiC MOSFETs. The ZVS design of a full-SiC TLNPC converter must not follow conventional methods for Silicon (Si) based converters. To address this issue, a modified design approach, which can guarantee ZVS of all switches in a full-SiC TLNPC dc-dc converter, is introduced and discussed. All of the analysis is verified on a 3 kW full-SiC TLNPC prototype, which has rated input voltage of 1.2 kV, output voltage of 600 V, and achieves ZVS in the output power range of 1.2 kW $\sim$ 3 kW.


  • Review of High-Temperature Power Electronics Converters

    by Yudi Xiao, Zhe Zhang, Martijn Sebastiaan Duraij, Tiberiu-Gabriel Zsurzsan, Michael A. E. Andersen

    Power electronics converters operating at elevated temperature usually have degraded performance, such as reduced efficiency, lower noise immunity, and decreased system reliability, compared to those operating at room temperature. Nevertheless, harsh-environment applications, such as deep earth drilling, automotive, avionics, and space exploration, have been utilizing converters in high-temperature environments and are continuously pushing the temperature limits higher and higher with the advances in device technologies and converter design methodologies. This article starts with a literature study to identify the temperature dependence and the temperature limits of individual components. Then, published works about high-temperature converters are examined. Their selection of components is compared. Experimental results are analyzed to reflect on the efficacy of different component selections. Finally, since the latest published high-temperature converter was developed more than five years ago, a 1-kV input, 520-V output, 1-kW, $150$ °C-ambient-temperature-rated dc–dc converter is designed with state-of-the-art devices. Based on the literature review, and the test of the $150$ °C prototype, the main challenges of designing high-temperature power electronics converters are identified and concluded to be time-consuming, difficult, and expensive characterization of components, lack of accurate and computationally efficient models of converters, and optimizing component selection within short development time.