Pekka Laukkanen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pekka Laukkanen has a total of 357 co-authors. Here are the top co-authors by number of shared publications:
M. Kuzmin
Department of Physics and Astronomy, University of Turku 1 , FI-20014 Turku, Finland
40 shared publications- Mircea Guina
Tampere University
28 shared publications K. Kokko
Univ Turku, Dept Phys & Astron, FI-20014 Turku, Finland
27 shared publicationsJ. Dahl
24 shared publicationsM. Tuominen
Department of Physics and Astronomy, University of Turku, FI-20014 Turku, Finland
22 shared publicationsI. J. Väyrynen
Department of Physics and Astronomy, University of Turku, FIN-20014 Turku, Finland
18 shared publications
Latest Publications
- 2 November 2026
- Published by American Physical Society (APS) in Physical Review B
- Vol. 114 (29)
Role of local structural variation in x-ray photoelectron spectrum of silicon oxide interfaces
- 2 November 2026
- Published by American Physical Society (APS) in Physical Review B
- Vol. 114 (29)
Role of local structural variation in x-ray photoelectron spectrum of silicon oxide interfaces
- Open Access
- 21 April 2026
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (8) , e202500987
Challenges in Simultaneous Microstructuring and Hyperdoping of Germanium with Ultrafast Laser
Germanium's compatibility with Complementary Metal‐Oxide‐Semiconductor (CMOS) and strong near‐infrared response make it an attractive platform for infrared photonics, but its intrinsic material properties hinder straightforward extension of absorption beyond the band edge. In this perspective, we synthesize recent and new experiments and analyses on femtosecond‐laser approaches that attempt to combine surface microstructuring and hyperdoping of Ge in a single step. We argue that, unlike silicon, Ge's high optical absorption at visible/green wavelengths, shallow energy deposition, lower melting point, and reduced thermal conductivity favor intense localized heating, evaporation, and redeposition—conditions that both produce high baseline sub‐bandgap absorption from damage and prevent effective incorporation of thin‐film dopant precursors. In a case example, Ti shows only trace incorporation from qualitative measurements. We discuss why laser‐induced structural disorder, rather than stable deep dopant incorporation, dominates the optical response, and we outline practical pathways forward: exploring longer wavelengths or gas‐phase chemistries, applying separate in situ heating, or decoupling texturing from heavy doping.
- 21 April 2026
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (8) , e202500987
Open AccessChallenges in Simultaneous Microstructuring and Hyperdoping of Germanium with Ultrafast Laser
Germanium's compatibility with Complementary Metal‐Oxide‐Semiconductor (CMOS) and strong near‐infrared response make it an attractive platform for infrared photonics, but its intrinsic material properties hinder straightforward extension of absorption beyond the band edge. In this perspective, we synthesize recent and new experiments and analyses on femtosecond‐laser approaches that attempt to combine surface microstructuring and hyperdoping of Ge in a single step. We argue that, unlike silicon, Ge's high optical absorption at visible/green wavelengths, shallow energy deposition, lower melting point, and reduced thermal conductivity favor intense localized heating, evaporation, and redeposition—conditions that both produce high baseline sub‐bandgap absorption from damage and prevent effective incorporation of thin‐film dopant precursors. In a case example, Ti shows only trace incorporation from qualitative measurements. We discuss why laser‐induced structural disorder, rather than stable deep dopant incorporation, dominates the optical response, and we outline practical pathways forward: exploring longer wavelengths or gas‐phase chemistries, applying separate in situ heating, or decoupling texturing from heavy doping.
- Open Access
- 24 January 2026
- Published by Wiley in Advanced Theory and Simulations
- Vol. 9 (1)
Atomic‐Level Insights Into the Initial Oxidative Crystallization of Si(100) to Periodic SiO x
MD Simulations based on force fields and first‐principles calculations based on density functional theory have been employed to investigate the initial stages of oxidation on silicon (100) surfaces exhibiting a p (2 × 2) reconstruction when exposed to atomic oxygen. Our results reveal that, when oxygen atoms are sequentially added to energetically preferred sites on the p (2 × 2) reconstructed Si(100) surface, the lattice maintains its crystallinity for up to three layers, in contrast to the typically observed disordered surface oxide. Detailed atomic and electronic structures of the crystalline SiO x /Si are presented, which provide a starting point model for the recent measurements of crystalline SiO x /Si formed under controlled oxidation conditions.
- 24 January 2026
- Published by Wiley in Advanced Theory and Simulations
- Vol. 9 (1)
Open AccessAtomic‐Level Insights Into the Initial Oxidative Crystallization of Si(100) to Periodic SiO x
MD Simulations based on force fields and first‐principles calculations based on density functional theory have been employed to investigate the initial stages of oxidation on silicon (100) surfaces exhibiting a p (2 × 2) reconstruction when exposed to atomic oxygen. Our results reveal that, when oxygen atoms are sequentially added to energetically preferred sites on the p (2 × 2) reconstructed Si(100) surface, the lattice maintains its crystallinity for up to three layers, in contrast to the typically observed disordered surface oxide. Detailed atomic and electronic structures of the crystalline SiO x /Si are presented, which provide a starting point model for the recent measurements of crystalline SiO x /Si formed under controlled oxidation conditions.
- Open Access
- 5 December 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (50) , 68802-68813
Transforming Schottky to Ohmic Contacts via Ultrahigh-Vacuum Engineered Interfacial Alloying
Low-resistive Ohmic contacts are needed in most microelectronics and photonics devices to connect a device to the electric circuit. Manufacturing of Ohmic contacts typically requires the doping of a semiconductor surface region as n-type or p-type (i.e., electron- or hole-doped, respectively). This task has, however, become challenging when the doping needs to be controlled with nanometer or even atomic level precision at lowered processing temperatures. In this work, we demonstrate a low-temperature method to tackle this contact manufacturing challenge using ultrathin antimony (Sb) doped germanium (Ge) nanolayers. We have integrated the method with the common lift-off processing to make Ohmic nickel (Ni) contacts on low-doped n-type Ge and Si substrates and on semi-insulating GaAs, which initially show the Schottky contacts. A proper combination of wet chemical cleaning plus depositing Sb and Ge atomic layers on the substrates, kept at room temperature, in a very clean environment of ultrahigh vacuum before the Ni-film deposition and postmetallization heating changes the Schottky contacts to Ohmic ones. Complementary methods are used to probe the physicochemical properties of interfaces during the manufacturing process to clarify the mechanisms behind the Ohmic-contact formation.
- 5 December 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (50) , 68802-68813
Open AccessTransforming Schottky to Ohmic Contacts via Ultrahigh-Vacuum Engineered Interfacial Alloying
Low-resistive Ohmic contacts are needed in most microelectronics and photonics devices to connect a device to the electric circuit. Manufacturing of Ohmic contacts typically requires the doping of a semiconductor surface region as n-type or p-type (i.e., electron- or hole-doped, respectively). This task has, however, become challenging when the doping needs to be controlled with nanometer or even atomic level precision at lowered processing temperatures. In this work, we demonstrate a low-temperature method to tackle this contact manufacturing challenge using ultrathin antimony (Sb) doped germanium (Ge) nanolayers. We have integrated the method with the common lift-off processing to make Ohmic nickel (Ni) contacts on low-doped n-type Ge and Si substrates and on semi-insulating GaAs, which initially show the Schottky contacts. A proper combination of wet chemical cleaning plus depositing Sb and Ge atomic layers on the substrates, kept at room temperature, in a very clean environment of ultrahigh vacuum before the Ni-film deposition and postmetallization heating changes the Schottky contacts to Ohmic ones. Complementary methods are used to probe the physicochemical properties of interfaces during the manufacturing process to clarify the mechanisms behind the Ohmic-contact formation.
- Open Access
- 8 November 2025
- Published by Elsevier in Applied Surface Science
- Vol. 720
Effect of H2O2 and H2O immersions on epitaxial GaInP-GaAs interfaces: Photoluminescence and x-ray photoelectron study
- 8 November 2025
- Published by Elsevier in Applied Surface Science
- Vol. 720
Open AccessEffect of H2O2 and H2O immersions on epitaxial GaInP-GaAs interfaces: Photoluminescence and x-ray photoelectron study
- Open Access
- 15 July 2025
- Published by Wiley in Advanced Photonics Research
- Vol. 6 (9)
Below 1% Reflectance for Black GaAs Surface Prepared by Facile Two‐Step Wet Chemical Treatment: Hydrogen Peroxide and Water
To increase performance of many photonic devices (e.g., solar cell, light emitting diode (LED), photodetector), it is essential to decrease light reflection at device interfaces. Sustainable and scalable methods have been intensively developed for manufacturing nanostructured antireflection coatings at device surfaces to reduce the reflection‐induced losses in them. In this work, a novel wet chemical method is demonstrated to prepare black nanostructured GaAs surfaces in scalable manner. This facile method includes two steps: immersion of GaAs in hot H2O2 solution followed by immersion in hot H2O both at around 80 °C. Microscopy, spectroscopy, and diffraction measurements reveal that the H2O2 immersion increases a surface porosity at GaAs while the hot‐water treatment causes the formation of GaOOH nanocrystals. Reflectivity at the resulting black GaAs surface is decreased even below 1% in a broadband. Photoluminescence intensity measurements are used to study whether the presented top‐to‐down method increases harmful non‐radiative recombination, as compared to the initial GaAs surface. Integration of the found black‐GaAs method with device manufacturing is presented by means of planar metal–GaAs–metal photodetectors, of which external quantum efficiency increases due to the method.
- 15 July 2025
- Published by Wiley in Advanced Photonics Research
- Vol. 6 (9)
Open AccessBelow 1% Reflectance for Black GaAs Surface Prepared by Facile Two‐Step Wet Chemical Treatment: Hydrogen Peroxide and Water
To increase performance of many photonic devices (e.g., solar cell, light emitting diode (LED), photodetector), it is essential to decrease light reflection at device interfaces. Sustainable and scalable methods have been intensively developed for manufacturing nanostructured antireflection coatings at device surfaces to reduce the reflection‐induced losses in them. In this work, a novel wet chemical method is demonstrated to prepare black nanostructured GaAs surfaces in scalable manner. This facile method includes two steps: immersion of GaAs in hot H2O2 solution followed by immersion in hot H2O both at around 80 °C. Microscopy, spectroscopy, and diffraction measurements reveal that the H2O2 immersion increases a surface porosity at GaAs while the hot‐water treatment causes the formation of GaOOH nanocrystals. Reflectivity at the resulting black GaAs surface is decreased even below 1% in a broadband. Photoluminescence intensity measurements are used to study whether the presented top‐to‐down method increases harmful non‐radiative recombination, as compared to the initial GaAs surface. Integration of the found black‐GaAs method with device manufacturing is presented by means of planar metal–GaAs–metal photodetectors, of which external quantum efficiency increases due to the method.
- Open Access
- 12 June 2025
- Published by Wiley in Advanced Materials Interfaces
- Vol. 12 (13)
Surface Properties of p‐GaN and Formation of Nickel Metal Contacts
Nickel (Ni) is the key component in ohmic contacts for Mg‐doped p‐GaN, but the detailed formation mechanisms of the ohmic contact have not yet been understood. In this work, the effect of potassium hydroxide (KOH)‐based chemical treatment on the surface of p‐GaN is investigated using X‐ray photoelectron spectroscopy (XPS), scanning tunneling microscopy (STM), and low‐energy electron diffraction (LEED). Ni metal contacts on the chemically treated p‐GaN surface are studied using transfer length method (TLM) and synchrotron radiation photoelectron spectroscopy (SR‐XPS). The chemical treatment of p‐GaN improves the brightness of the (1x1) hexagonal diffraction pattern in LEED and keeps the 2D terrace structure in STM visible. Concomitantly, XPS shows that the amount of O, C, and Mg–O bonds at the surface were reduced. Ni/p‐GaN provided an ohmic contact after annealing in ultra‐high vacuum (UHV) at 500 °C. Simultaneously, SR‐XPS shows the diffusion of Ga to Ni and the formation of a previously unreported Ga 3d component, which has a surprisingly narrow line shape, indicating that it originates from a crystalline interface phase. Diffusion of Ga is discussed to cause Ga vacancies and acceptor levels in the bandgap increasing carrier tunneling, thus enabling ohmic contact.
- 12 June 2025
- Published by Wiley in Advanced Materials Interfaces
- Vol. 12 (13)
Open AccessSurface Properties of p‐GaN and Formation of Nickel Metal Contacts
Nickel (Ni) is the key component in ohmic contacts for Mg‐doped p‐GaN, but the detailed formation mechanisms of the ohmic contact have not yet been understood. In this work, the effect of potassium hydroxide (KOH)‐based chemical treatment on the surface of p‐GaN is investigated using X‐ray photoelectron spectroscopy (XPS), scanning tunneling microscopy (STM), and low‐energy electron diffraction (LEED). Ni metal contacts on the chemically treated p‐GaN surface are studied using transfer length method (TLM) and synchrotron radiation photoelectron spectroscopy (SR‐XPS). The chemical treatment of p‐GaN improves the brightness of the (1x1) hexagonal diffraction pattern in LEED and keeps the 2D terrace structure in STM visible. Concomitantly, XPS shows that the amount of O, C, and Mg–O bonds at the surface were reduced. Ni/p‐GaN provided an ohmic contact after annealing in ultra‐high vacuum (UHV) at 500 °C. Simultaneously, SR‐XPS shows the diffusion of Ga to Ni and the formation of a previously unreported Ga 3d component, which has a surprisingly narrow line shape, indicating that it originates from a crystalline interface phase. Diffusion of Ga is discussed to cause Ga vacancies and acceptor levels in the bandgap increasing carrier tunneling, thus enabling ohmic contact.
- Open Access
- 4 March 2025
- Published by Elsevier in Applied Surface Science
- Vol. 695
Effects of ultra-high vacuum treatments on n-type Si contact resistivity
- 4 March 2025
- Published by Elsevier in Applied Surface Science
- Vol. 695
Open AccessEffects of ultra-high vacuum treatments on n-type Si contact resistivity
- Open Access
- 3 February 2025
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 19 (3)
Passivation of Germanium Surfaces by HF:H2O2 Aqueous Solution
Promising intrinsic electronic properties, such as narrow bandgap and high charge carrier mobilities, make germanium (Ge) a good replacement for silicon in optoelectronic applications (e.g., photodetectors). However, successful fabrication of efficient Ge devices requires minimization of both reflectance and surface recombination losses. This work begins with an observation that metal‐assisted chemical etching (MACE) of Ge surfaces, used for optics improvement, reduces surface recombination without application of any intentional passivation. We proceed with investigation of the effect of MACE solution components and their mixtures on Ge surface passivation. The results demonstrate that HF:H2O2 aqueous solution leads to efficient and stable passivation. The film formed in this solution secures surface recombination velocity (Seff) of 14 cm s−1. Morphological and chemical characterization of the structure reveals porous germanium (PGe) layer with some GeOx included. Finally, we propose several hypotheses on a mechanism behind this passivation, among which are the presence of GeO2 at the film‐bulk Ge interface and appearance of a potential barrier due to the heterojunction formation. The presented Ge passivation with PGe layer provides a simple and cost‐efficient alternative to existing state‐of‐the‐art passivation schemes.
- 3 February 2025
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 19 (3)
Open AccessPassivation of Germanium Surfaces by HF:H2O2 Aqueous Solution
Promising intrinsic electronic properties, such as narrow bandgap and high charge carrier mobilities, make germanium (Ge) a good replacement for silicon in optoelectronic applications (e.g., photodetectors). However, successful fabrication of efficient Ge devices requires minimization of both reflectance and surface recombination losses. This work begins with an observation that metal‐assisted chemical etching (MACE) of Ge surfaces, used for optics improvement, reduces surface recombination without application of any intentional passivation. We proceed with investigation of the effect of MACE solution components and their mixtures on Ge surface passivation. The results demonstrate that HF:H2O2 aqueous solution leads to efficient and stable passivation. The film formed in this solution secures surface recombination velocity (Seff) of 14 cm s−1. Morphological and chemical characterization of the structure reveals porous germanium (PGe) layer with some GeOx included. Finally, we propose several hypotheses on a mechanism behind this passivation, among which are the presence of GeO2 at the film‐bulk Ge interface and appearance of a potential barrier due to the heterojunction formation. The presented Ge passivation with PGe layer provides a simple and cost‐efficient alternative to existing state‐of‐the‐art passivation schemes.
- Open Access
- 30 August 2024
- Published by Elsevier in Applied Surface Science
- Vol. 678
Dry cleaning of InSb surfaces by hydrogen molecule exposure in ultrahigh vacuum
- 30 August 2024
- Published by Elsevier in Applied Surface Science
- Vol. 678
Open AccessDry cleaning of InSb surfaces by hydrogen molecule exposure in ultrahigh vacuum