Russell Allan Maier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Russell Allan Maier has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
- Igor Levin
Materials Measurement Science Division, National Institute of Standards and Technology, Gaithersburg, MD, USA.
6 shared publications - Andrew P. Allen
Materials Measurement Science Division, National Institute of Standards and Technology, Gaithersburg, MD 20899, USA
5 shared publications - Aaron C. Johnston-Peck
Material Measurement Laboratory National Institute of Standards and Technology Gaithersburg Maryland USA
4 shared publications C. A. Randall
Pennsylvania State University, University Park 3 Materials Science and Engineering 16802, USA
3 shared publications- Clive A. Randall
Department of Materials Science and Engineering The Pennsylvania State University University Park Pennsylvania USA
3 shared publications - Fan Zhang
Materials Measurement Science Division, National Institute of Standards and Technology, Gaithersburg, MD 20899, USA
3 shared publications
Latest Publications
- 20 April 2026
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 109 (4)
Reactive Sintering of Oxide Nanoceramic Composites via a Redox‐Driven Eutectoid Synthesis Route
A novel reactive sintering method was developed to produce dense ceramics with nanoscale composite microstructures. This method exploits the variable valence state of cerium ions. Compounds that contain cerium cations can undergo oxidation–reduction (redox) reactions depending on the oxygen activity of the processing environment. The perovskite cerium(III) aluminate, CeAlO 3 , undergoes a eutectoid transformation in oxidizing conditions to form nanoscale lamella of cerium(IV) dioxide, CeO 2 , and Al 2 O 3 . Unlike a typical eutectoid reaction, the redox activity of cerium provides an additional lever of control (oxygen partial pressure) over the onset and kinetics of the eutectoid transformation. Multiple processes that affect the final sintered microstructure (densification, coarsening, and volume expansion) of a ceramic can negatively interact and result in porosity or coarsening. By controlling the oxygen atmosphere during sintering, the rates of these competing processes can be optimized to yield a fine‐featured and dense product. Testing indicates that finer CeO 2 /Al 2 O 3 composite microstructures exhibit improved hardness, and microscopy results indicate that these nano‐features introduce crack deflection mechanisms. This reactive sintering method provides a tool to produce bulk ceramics with near‐theoretical densities and nanoscale microstructures, a method that may be generalized to other oxide systems that undergo redox‐activated eutectoid transformations.
- 20 April 2026
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 109 (4)
Reactive Sintering of Oxide Nanoceramic Composites via a Redox‐Driven Eutectoid Synthesis Route
A novel reactive sintering method was developed to produce dense ceramics with nanoscale composite microstructures. This method exploits the variable valence state of cerium ions. Compounds that contain cerium cations can undergo oxidation–reduction (redox) reactions depending on the oxygen activity of the processing environment. The perovskite cerium(III) aluminate, CeAlO 3 , undergoes a eutectoid transformation in oxidizing conditions to form nanoscale lamella of cerium(IV) dioxide, CeO 2 , and Al 2 O 3 . Unlike a typical eutectoid reaction, the redox activity of cerium provides an additional lever of control (oxygen partial pressure) over the onset and kinetics of the eutectoid transformation. Multiple processes that affect the final sintered microstructure (densification, coarsening, and volume expansion) of a ceramic can negatively interact and result in porosity or coarsening. By controlling the oxygen atmosphere during sintering, the rates of these competing processes can be optimized to yield a fine‐featured and dense product. Testing indicates that finer CeO 2 /Al 2 O 3 composite microstructures exhibit improved hardness, and microscopy results indicate that these nano‐features introduce crack deflection mechanisms. This reactive sintering method provides a tool to produce bulk ceramics with near‐theoretical densities and nanoscale microstructures, a method that may be generalized to other oxide systems that undergo redox‐activated eutectoid transformations.
- 28 October 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 108 (2)
Interlaboratory study of flexural strength in additively manufactured alumina
We report the results of an international interlaboratory study of the flexural strength of alumina fabricated across six laboratories using the vat photopolymerization ceramic additive manufacturing (AM) technology. The mechanical testing of all the specimens, 142 in total, was performed at the National Institute of Standards and Technology (NIST) according to the well‐established four‐point bending method standardized for traditional ceramics. Overall, the existing ASTM standard for the four‐point bend testing proved adequate for AM ceramics, with several modifications to the specimen requirements to account for the specifics of AM processes. Critical flaws that caused failure were identified in all but two cases using optical fractography augmented with the imaging of fracture surfaces in a scanning electron microscope. The flexural strength data, analyzed following the Weibull statistics, exhibited considerable variation among the specimen sets manufactured by different laboratories. This variability correlated with the presence of many distinct critical flaws. We identified seven types of flaws that accounted for the failure of 94% of specimens. The prevalent flaws depend on the printing direction relative to the specimen's geometry. We discuss the nature of these flaws and their relation to the printing and post‐processing conditions. Removal of several types of critical flaws will significantly improve mechanical properties of ceramic parts built using vat‐photopolymerization AM.
- 28 October 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 108 (2)
Interlaboratory study of flexural strength in additively manufactured alumina
We report the results of an international interlaboratory study of the flexural strength of alumina fabricated across six laboratories using the vat photopolymerization ceramic additive manufacturing (AM) technology. The mechanical testing of all the specimens, 142 in total, was performed at the National Institute of Standards and Technology (NIST) according to the well‐established four‐point bending method standardized for traditional ceramics. Overall, the existing ASTM standard for the four‐point bend testing proved adequate for AM ceramics, with several modifications to the specimen requirements to account for the specifics of AM processes. Critical flaws that caused failure were identified in all but two cases using optical fractography augmented with the imaging of fracture surfaces in a scanning electron microscope. The flexural strength data, analyzed following the Weibull statistics, exhibited considerable variation among the specimen sets manufactured by different laboratories. This variability correlated with the presence of many distinct critical flaws. We identified seven types of flaws that accounted for the failure of 94% of specimens. The prevalent flaws depend on the printing direction relative to the specimen's geometry. We discuss the nature of these flaws and their relation to the printing and post‐processing conditions. Removal of several types of critical flaws will significantly improve mechanical properties of ceramic parts built using vat‐photopolymerization AM.
- 27 June 2024
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 57 (4) , 1023-1039
Approaches and challenges in whole-nanoparticle refinements from neutron total-scattering data
This study considers critical data reduction steps and data analysis approaches required to determine explicitly the atomic arrangements in nanoparticles from time-of-flight neutron total scattering. A practical procedure is described for removing parasitic backgrounds caused by the incoherent scattering of hydrogen inevitably present in most nanoparticle samples and normalizing the recovered coherent scattering intensities onto an absolute scale. A model-free analysis is presented of a pair-distribution function derived from total scattering that can be used to determine thermal expansion coefficients and particle sizes directly from experimental data without knowledge of the material's structure. Finally, atomistic whole-nanoparticle refinements of yttrium-doped ceria nanoparticles from neutron total-scattering data are demonstrated using the reverse Monte Carlo method implemented in the RMCProfile software. These results reveal a strong dependence of the cation–oxygen and oxygen–oxygen distances on the coordination numbers, which leads to gradients of these distances near the particle surface. The details are dependent on the surface coverage by ligands and adsorbates and on the structure of grain boundaries in nanocrystalline agglomerates. The refined models confirm the expectations of more substantial disorder at particle surfaces, with a distorted surface layer extending over several coordination shells. The results highlight the feasibility of whole-nanoparticle refinements from neutron data, calling for further development of data reduction and analysis procedures.
- 27 June 2024
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 57 (4) , 1023-1039
Approaches and challenges in whole-nanoparticle refinements from neutron total-scattering data
This study considers critical data reduction steps and data analysis approaches required to determine explicitly the atomic arrangements in nanoparticles from time-of-flight neutron total scattering. A practical procedure is described for removing parasitic backgrounds caused by the incoherent scattering of hydrogen inevitably present in most nanoparticle samples and normalizing the recovered coherent scattering intensities onto an absolute scale. A model-free analysis is presented of a pair-distribution function derived from total scattering that can be used to determine thermal expansion coefficients and particle sizes directly from experimental data without knowledge of the material's structure. Finally, atomistic whole-nanoparticle refinements of yttrium-doped ceria nanoparticles from neutron total-scattering data are demonstrated using the reverse Monte Carlo method implemented in the RMCProfile software. These results reveal a strong dependence of the cation–oxygen and oxygen–oxygen distances on the coordination numbers, which leads to gradients of these distances near the particle surface. The details are dependent on the surface coverage by ligands and adsorbates and on the structure of grain boundaries in nanocrystalline agglomerates. The refined models confirm the expectations of more substantial disorder at particle surfaces, with a distorted surface layer extending over several coordination shells. The results highlight the feasibility of whole-nanoparticle refinements from neutron data, calling for further development of data reduction and analysis procedures.
- 17 June 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (10) , 6544-6553
In situ observation of the multistep process of cold sintering
A compact cold sintering stage was constructed to densify ceramic samples in capillary tubes for the purpose of conducting in situ experiments designed to elucidate fundamental cold sintering mechanisms. The stage was used to successfully densify samples composed of ZnO/CH₃COOH mixtures under a range of pressures (25–175 MPa) over a modest temperature range (room to 150°C) in capillary tubes (0.75 mm inner diameter). The progression of the cold sintering process of ZnO was monitored by both piston displacement and a camera. These measurements allowed the strain rate and fluid extraction during densification to be recorded. The results of these measurements are compared to existing models of cold sintering and pressure solution creep, and direct correlations are observed between abrupt changes to the densification rate during constant heating rate experiments and the observation of solvent extraction from the powder compact.
- 17 June 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (10) , 6544-6553
In situ observation of the multistep process of cold sintering
A compact cold sintering stage was constructed to densify ceramic samples in capillary tubes for the purpose of conducting in situ experiments designed to elucidate fundamental cold sintering mechanisms. The stage was used to successfully densify samples composed of ZnO/CH₃COOH mixtures under a range of pressures (25–175 MPa) over a modest temperature range (room to 150°C) in capillary tubes (0.75 mm inner diameter). The progression of the cold sintering process of ZnO was monitored by both piston displacement and a camera. These measurements allowed the strain rate and fluid extraction during densification to be recorded. The results of these measurements are compared to existing models of cold sintering and pressure solution creep, and direct correlations are observed between abrupt changes to the densification rate during constant heating rate experiments and the observation of solvent extraction from the powder compact.
- 3 March 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (7) , 5093-5104
Eutectoid decompositions in Ce‐containing ABO 3 perovskites: Part II, the case of divorced growth in CeCrO 3
A eutectoid phase transformation was exhibited by the perovskite CeCrO 3 when heated in air. The kinetics of the reaction, microstructure of the product, and mechanisms of the transformation were studied using thermogravimetric analysis, X‐ray and Raman spectroscopy, X‐ray diffraction, and electron microscopy. Fluorite CeO 2 and corundum Cr 2 O 3 were formed from the decomposition of CeCrO 3 . The CeO 2 particles were porous and polycrystalline, a consequence of nucleation, growth, and impingent of CeO 2 domains on the CeCrO 3 particles. Anisotropic growth is indicated by the morphology of the CeO 2 grains, while the Cr 2 O 3 particles were single crystals without any crystallographic orientation relationship to the parent phase. Unlike the CeAlO 3 eutectoid, the microstructure comprised of CeO 2 and Cr 2 O 3 show no characteristics of a microstructure formed by cooperative growth. The disparity between the eutectoid reactions in CeCrO 3 and CeAlO 3 is attributed to a difference in interfacial energy between the fluorite and sesquioxide phases (i.e., CeO 2 /Al 2 O 3 versus CeO 2 /Cr 2 O 3 ).
- 3 March 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (7) , 5093-5104
Eutectoid decompositions in Ce‐containing ABO 3 perovskites: Part II, the case of divorced growth in CeCrO 3
A eutectoid phase transformation was exhibited by the perovskite CeCrO 3 when heated in air. The kinetics of the reaction, microstructure of the product, and mechanisms of the transformation were studied using thermogravimetric analysis, X‐ray and Raman spectroscopy, X‐ray diffraction, and electron microscopy. Fluorite CeO 2 and corundum Cr 2 O 3 were formed from the decomposition of CeCrO 3 . The CeO 2 particles were porous and polycrystalline, a consequence of nucleation, growth, and impingent of CeO 2 domains on the CeCrO 3 particles. Anisotropic growth is indicated by the morphology of the CeO 2 grains, while the Cr 2 O 3 particles were single crystals without any crystallographic orientation relationship to the parent phase. Unlike the CeAlO 3 eutectoid, the microstructure comprised of CeO 2 and Cr 2 O 3 show no characteristics of a microstructure formed by cooperative growth. The disparity between the eutectoid reactions in CeCrO 3 and CeAlO 3 is attributed to a difference in interfacial energy between the fluorite and sesquioxide phases (i.e., CeO 2 /Al 2 O 3 versus CeO 2 /Cr 2 O 3 ).
- 7 December 2023
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (4) , 2765-2775
Eutectoid decompositions in Ce‐containing ABO 3 perovskites: Part I, the case of cooperative growth in CeAlO 3
Oxidation of perovskite CeAlO 3 results in the eutectoid transformation to CeO 2 and Al 2 O 3 . This phase transformation was recorded using thermal gravimetric analysis, X‐ray diffraction, and scanning transmission electron microscopy. Lamellar features in the resultant microstructure indicate cooperative growth. Processing conditions dictate the lamellae sizes, which can be as small as a few nanometers, and coarsen into large domains with additional high temperature annealing.
- 7 December 2023
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (4) , 2765-2775
Eutectoid decompositions in Ce‐containing ABO 3 perovskites: Part I, the case of cooperative growth in CeAlO 3
Oxidation of perovskite CeAlO 3 results in the eutectoid transformation to CeO 2 and Al 2 O 3 . This phase transformation was recorded using thermal gravimetric analysis, X‐ray diffraction, and scanning transmission electron microscopy. Lamellar features in the resultant microstructure indicate cooperative growth. Processing conditions dictate the lamellae sizes, which can be as small as a few nanometers, and coarsen into large domains with additional high temperature annealing.
- 23 August 2023
- Published by Elsevier in Acta Materialia
- Vol. 259, 119283
In situ probing of interfacial roughness and transient phases during ceramic cold sintering process
- 23 August 2023
- Published by Elsevier in Acta Materialia
- Vol. 259, 119283
In situ probing of interfacial roughness and transient phases during ceramic cold sintering process
- Open Access
- 18 October 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (20) , 10493
In Situ Microstructure Characterization of Potassium Di-Phosphate (KDP) Densification during Cold Sintering
In order for ceramic additive manufacturing (AM) to achieve its full potential, it is increasingly important to develop a more rigorous understanding of fundamental phenomena that govern the kinetics and thermodynamics of ceramic AM processes. In the case of additive build processes, such as direct ink write and ceramic extrusion, methods for densifying the resulting green-body product need to be considered to complement the efficiencies of ceramics AM, itself. One densification route, at least for monolithic components, built layer-by-layer, is offered by the recently developed cold sintering process, whereby high-density final product is achieved through addition of a small amount of liquid solvent and application of modest uniaxial compressive stress at relatively low temperature. In situ small-angle X-ray scattering methods and X-ray diffraction have been applied to characterize and quantify the pore morphology evolution during cold sintering for a model system: potassium di-phosphate, KH2PO4 (KDP). It is shown that both temperature and applied stress affect the densification rate, but stress has a stronger effect on the evolving morphology. A regime with an approximate linear densification rate can be identified, yielding an effective densification activation energy of ≈90 kJ/mol.
- 18 October 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (20) , 10493
Open AccessIn Situ Microstructure Characterization of Potassium Di-Phosphate (KDP) Densification during Cold Sintering
In order for ceramic additive manufacturing (AM) to achieve its full potential, it is increasingly important to develop a more rigorous understanding of fundamental phenomena that govern the kinetics and thermodynamics of ceramic AM processes. In the case of additive build processes, such as direct ink write and ceramic extrusion, methods for densifying the resulting green-body product need to be considered to complement the efficiencies of ceramics AM, itself. One densification route, at least for monolithic components, built layer-by-layer, is offered by the recently developed cold sintering process, whereby high-density final product is achieved through addition of a small amount of liquid solvent and application of modest uniaxial compressive stress at relatively low temperature. In situ small-angle X-ray scattering methods and X-ray diffraction have been applied to characterize and quantify the pore morphology evolution during cold sintering for a model system: potassium di-phosphate, KH2PO4 (KDP). It is shown that both temperature and applied stress affect the densification rate, but stress has a stronger effect on the evolving morphology. A regime with an approximate linear densification rate can be identified, yielding an effective densification activation energy of ≈90 kJ/mol.
- 12 October 2022
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 106 (2) , 1490-1499
Adlayer formation on C‐plane (0001) and R‐plane (11¯${\rm{\bar{1}}}$02) Al 2 O 3 surfaces
Adlayers on C‐plane (0001) and R‐plane (102) terminated surfaces of corundum phase aluminum oxide were synthesized by annealing mixtures of two oxide powders, aluminum oxide with an additive. Using high‐angle annular dark field scanning transmission electron microscopy, the adsorbed layers were characterized, and image simulations aided interpretation of the results. The adlayers were pseudomorphic, one atomic layer thick, and with a fractional site occupancy. Atomic positions of the adlayer atoms relaxed and changed relative to the bulk structure, where there is evidence that the magnitude of the relaxation is sensitive to the ionic radius of the adsorbate. The pseudomorphic adlayer structure is formed for different elements including, but not limited to, the lanthanides (i.e., Ge, Ba, and Ln = La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Tm).
- 12 October 2022
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 106 (2) , 1490-1499
Adlayer formation on C‐plane (0001) and R‐plane (11¯${\rm{\bar{1}}}$02) Al 2 O 3 surfaces
Adlayers on C‐plane (0001) and R‐plane (102) terminated surfaces of corundum phase aluminum oxide were synthesized by annealing mixtures of two oxide powders, aluminum oxide with an additive. Using high‐angle annular dark field scanning transmission electron microscopy, the adsorbed layers were characterized, and image simulations aided interpretation of the results. The adlayers were pseudomorphic, one atomic layer thick, and with a fractional site occupancy. Atomic positions of the adlayer atoms relaxed and changed relative to the bulk structure, where there is evidence that the magnitude of the relaxation is sensitive to the ionic radius of the adsorbate. The pseudomorphic adlayer structure is formed for different elements including, but not limited to, the lanthanides (i.e., Ge, Ba, and Ln = La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Tm).
- Open Access
- 10 August 2022
- Published by Wiley in International Journal of Ceramic Engineering & Science
- Vol. 4 (5) , 302-308
Research, standards, and data needs for industrialization of ceramic direct ink writing
Here, we summarize a panel discussion on the direct ink writing (DIW) of ceramics, organized and moderated by the National Institute of Standards and Technology at the American Ceramic Society's 46th International Conference on Advanced Ceramics and Composites in January 2022. The panel reviewed the current state of the art in DIW, focusing on research directions, standards development, and data needs required to facilitate industrial adoption of these technologies. The panel agreed to form working groups for (1) exploring how the community can work together to develop and curate public databases of feedstock characteristics and properties of end‐products and (2) organizing an international round‐robin to compare performance properties of DIW‐manufactured ceramics, potentially tied to ASTM/ISO standards development.
- 10 August 2022
- Published by Wiley in International Journal of Ceramic Engineering & Science
- Vol. 4 (5) , 302-308
Open AccessResearch, standards, and data needs for industrialization of ceramic direct ink writing
Here, we summarize a panel discussion on the direct ink writing (DIW) of ceramics, organized and moderated by the National Institute of Standards and Technology at the American Ceramic Society's 46th International Conference on Advanced Ceramics and Composites in January 2022. The panel reviewed the current state of the art in DIW, focusing on research directions, standards development, and data needs required to facilitate industrial adoption of these technologies. The panel agreed to form working groups for (1) exploring how the community can work together to develop and curate public databases of feedstock characteristics and properties of end‐products and (2) organizing an international round‐robin to compare performance properties of DIW‐manufactured ceramics, potentially tied to ASTM/ISO standards development.