Bert C. Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Bert C. Liu has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Glenn S. Daehn
Department of Materials Science and Engineering, The Ohio State University, Columbus, OH 43210, USA
7 shared publications Anupam Vivek
The Ohio State University
6 shared publications- Anupam Vivek
The Ohio State University
6 shared publications Glenn S. Daehn
The Ohio State University
5 shared publications- Steven R. Hansen
The Ohio State University, Columbus, OH
4 shared publications A. Vivek
3 shared publications
Latest Publications
- 28 August 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 104 (9-12) , 4593-4604
Impact welding of ultra-high-strength stainless steel in wrought vs. additively manufactured forms
- 28 August 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 104 (9-12) , 4593-4604
Impact welding of ultra-high-strength stainless steel in wrought vs. additively manufactured forms
- 28 March 2019
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (13) , 9824-9842
Experimental and numerical investigation of interfacial microstructure in fully age-hardened 15-5 PH stainless steel during impact welding
- 28 March 2019
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (13) , 9824-9842
Experimental and numerical investigation of interfacial microstructure in fully age-hardened 15-5 PH stainless steel during impact welding
- 1 December 2017
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 30, 75-82
Joining sheet aluminum AA6061-T4 to cast magnesium AM60B by vaporizing foil actuator welding: Input energy, interface, and strength
- 1 December 2017
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 30, 75-82
Joining sheet aluminum AA6061-T4 to cast magnesium AM60B by vaporizing foil actuator welding: Input energy, interface, and strength
- 5 June 2017
- Published by AIP Publishing in Applied Physics Letters
- Vol. 110 (23) , 231601
Depiction of interfacial morphology in impact welded Ti/Cu bimetallic systems using smoothed particle hydrodynamics
Numerical simulations of high-velocity impact welding are extremely challenging due to the coupled physics and highly dynamic nature of the process. Thus, conventional mesh-based numerical methodologies are not able to accurately model the process owing to the excessive mesh distortion close to the interface of two welded materials. A simulation platform was developed using smoothed particle hydrodynamics, implemented in a parallel architecture on a supercomputer. Then, the numerical simulations were compared to experimental tests conducted by vaporizing foil actuator welding. The close correspondence of the experiment and modeling in terms of interface characteristics allows the prediction of local temperature and strain distributions, which are not easily measured.
- 5 June 2017
- Published by AIP Publishing in Applied Physics Letters
- Vol. 110 (23) , 231601
Depiction of interfacial morphology in impact welded Ti/Cu bimetallic systems using smoothed particle hydrodynamics
Numerical simulations of high-velocity impact welding are extremely challenging due to the coupled physics and highly dynamic nature of the process. Thus, conventional mesh-based numerical methodologies are not able to accurately model the process owing to the excessive mesh distortion close to the interface of two welded materials. A simulation platform was developed using smoothed particle hydrodynamics, implemented in a parallel architecture on a supercomputer. Then, the numerical simulations were compared to experimental tests conducted by vaporizing foil actuator welding. The close correspondence of the experiment and modeling in terms of interface characteristics allows the prediction of local temperature and strain distributions, which are not easily measured.
- 1 April 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 659, 12-21
Interfacial microstructures and mechanical property of vaporizing foil actuator welding of aluminum alloy to steel
- 1 April 2016
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 659, 12-21
Interfacial microstructures and mechanical property of vaporizing foil actuator welding of aluminum alloy to steel
- 14 April 2015
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Impact Welding of Aluminum Alloy 6061 to Dual Phase 780 Steel Using Vaporizing Foil Actuator
Vaporizing Foil Actuators (VFA) are based on the phenomenon of rapid vaporization of thin metallic foils and wires, caused by passage of a capacitor bank driven current on the order of 100 kA. The burst of the conductor is accompanied with a high-pressure pulse, which can be used for working metal at high strain rates. This paper focuses on the use of VFA for collision welding of dissimilar metals, in particular, aluminum and steel. Aluminum alloy 6061 sheets of 1 mm thickness were launched to velocities in excess of 650 m/s with input electrical energy of 8 kJ into 0.0762 mm thick, dog-bone shaped aluminum foil actuators. Target sheets made from dual phase steel (DP780) were impacted with the aluminum flyer sheet, and solid state impact welds were created. During mechanical testing, many samples failed outside the weld area, thereby indicating that the weld was stronger than the parent aluminum. The samples that failed inside the weld region were found to have regions of brittle as well as ductile fracture. Metallography of the samples revealed that the interfaces had a wavy morphology that is typical for impact welds. Intermittent regions of intermetallic compounds were seen along the interface.
- 14 April 2015
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Impact Welding of Aluminum Alloy 6061 to Dual Phase 780 Steel Using Vaporizing Foil Actuator
Vaporizing Foil Actuators (VFA) are based on the phenomenon of rapid vaporization of thin metallic foils and wires, caused by passage of a capacitor bank driven current on the order of 100 kA. The burst of the conductor is accompanied with a high-pressure pulse, which can be used for working metal at high strain rates. This paper focuses on the use of VFA for collision welding of dissimilar metals, in particular, aluminum and steel. Aluminum alloy 6061 sheets of 1 mm thickness were launched to velocities in excess of 650 m/s with input electrical energy of 8 kJ into 0.0762 mm thick, dog-bone shaped aluminum foil actuators. Target sheets made from dual phase steel (DP780) were impacted with the aluminum flyer sheet, and solid state impact welds were created. During mechanical testing, many samples failed outside the weld area, thereby indicating that the weld was stronger than the parent aluminum. The samples that failed inside the weld region were found to have regions of brittle as well as ductile fracture. Metallography of the samples revealed that the interfaces had a wavy morphology that is typical for impact welds. Intermittent regions of intermetallic compounds were seen along the interface.