Anastasiia Kravchenko
Research Subjects
Research Interests
Anastasiia Kravchenko has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Pavlo Kryvenko
Scientific Research Institute for Binders and Materials, Kyiv National University of Construction and Architecture, 03037 Kyiv, Ukraine
4 shared publications - Sergii Guzii
Kyiv National University of Construction and Architecture
4 shared publications - Konstantinos Sotiriadis
Czech Academy of Sciences
2 shared publications Vít Petranek
Brno University of Technology
2 shared publicationsYurii Tsapko
Kiev National University of Civil Engineering and Architecture
2 shared publicationsPavel Krivenko
Kiev National University of Civil Engineering and Architecture
1 shared publication
Latest Publications
- Open Access
- 30 October 2016
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (10 (83)) , 26-31
Determination of the effect of fillers on the intumescent ability of the organic-inorganic coatings of building constructions
The analysis of methods of determining the intumescent ability of fireretardant coatings was performed, and the need to develop reliable methods for the study of the blistering process for the creation of new types of coatings was identified. Evaluation of the swelling ratio of inorganic and organic coatings, revealed the unreliability of the real values of the kinetics of decomposition of materials. The method for determining the kinetics of swelling of coatings was validated, and with the constant heat and mass transfer conditions during the test, the device was designed. Studies of the kinetics of swelling of organicinorganic coatings by this method have shown that under prolonged exposure to high temperature, the swelling coefficient decreases due to the foamcoke burnout. The results of determining the intumescent ability of coatings when adding fillers showed that when exposed to hightemperature stream, the material burnout and the coating weight loss are reduced by more than half due to the formation of hightemperature compounds, and this increases the time to reach the limit temperature. As a result of thermogravimetric study, the weight loss of the coatings depending on the temperature was determined, the activation energy was investigated in the temperature expansion of the coatings and it was found that for organicinorganic coating, it was 18.79 kJ/mol, and in the case of the introduction of fillers – tripled. These data suggest the feasibility of the use of fillers based on oxides and hydroxides to improve the efficiency of organicinorganic coatings.
- 30 October 2016
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (10 (83)) , 26-31
Open AccessDetermination of the effect of fillers on the intumescent ability of the organic-inorganic coatings of building constructions
The analysis of methods of determining the intumescent ability of fireretardant coatings was performed, and the need to develop reliable methods for the study of the blistering process for the creation of new types of coatings was identified. Evaluation of the swelling ratio of inorganic and organic coatings, revealed the unreliability of the real values of the kinetics of decomposition of materials. The method for determining the kinetics of swelling of coatings was validated, and with the constant heat and mass transfer conditions during the test, the device was designed. Studies of the kinetics of swelling of organicinorganic coatings by this method have shown that under prolonged exposure to high temperature, the swelling coefficient decreases due to the foamcoke burnout. The results of determining the intumescent ability of coatings when adding fillers showed that when exposed to hightemperature stream, the material burnout and the coating weight loss are reduced by more than half due to the formation of hightemperature compounds, and this increases the time to reach the limit temperature. As a result of thermogravimetric study, the weight loss of the coatings depending on the temperature was determined, the activation energy was investigated in the temperature expansion of the coatings and it was found that for organicinorganic coating, it was 18.79 kJ/mol, and in the case of the introduction of fillers – tripled. These data suggest the feasibility of the use of fillers based on oxides and hydroxides to improve the efficiency of organicinorganic coatings.
- 3 August 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1122, 7-10
Research of Fire-Retardant Properties of Timber Constructions, Protected Geocement-Based Coating, after their Operation
Was conducted survey of condition and fire-retardant properties of surface of timber constructions, protected by coating on geocement-based, after their operation under atmospheric conditions. For a comprehensive assessment of fire-retardant determined following characteristics: type of corrosive environment; duration of operation of structural elements coated; coating thickness and integrity; cracks; adhesion of the coating to the timber; determination of the fire-retardant properties of the coating. Assessment of the results obtained, despite the significant deterioration in the appearance of geocement-based coating retains its primary function, fire protection, having after one year of operation, – 1 group of combustibility.
- 3 August 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1122, 7-10
Research of Fire-Retardant Properties of Timber Constructions, Protected Geocement-Based Coating, after their Operation
Was conducted survey of condition and fire-retardant properties of surface of timber constructions, protected by coating on geocement-based, after their operation under atmospheric conditions. For a comprehensive assessment of fire-retardant determined following characteristics: type of corrosive environment; duration of operation of structural elements coated; coating thickness and integrity; cracks; adhesion of the coating to the timber; determination of the fire-retardant properties of the coating. Assessment of the results obtained, despite the significant deterioration in the appearance of geocement-based coating retains its primary function, fire protection, having after one year of operation, – 1 group of combustibility.
- 3 August 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1122, 11-14
Heat-Reflecting Geocement Based Coatings Containing Perlite for Fire Protection of Timber
In this paper, the application of a heat-reflecting geocement coating, containing perlite, to reduce timber combustibility was studied. An optimized coating composition was prepared, which consisted of a geocement (Na2O·Al2O3·6SiO2·21.5H2O) and expanded perlite (9.5%). The main firing properties of this coating were invastigated. In terms of flammability, the fire protected timber reduces mass loss by 13 times and temperature of combustion gases by 5.2 times compared to unprotected timber. According to standard indicators, the reduction is by 1.3 and 10 times, respectively. The smoke generation of fire protected timber was decreased by 4.9 times (combustion mode) and 3.8 times (smoldering mode) in comparison to the unprotected timber. According to standard indicators, the decrease is by 4.5 and 2.3 times for each mode, respectively. The index of flame spread and the combustion rate reduced by 20.3 and 6.3 times, respectively, in the case of the fire protected timber compared to the unprotected one. The pine timber protected by heat-reflecting fireproofing geocement based coating, which contains perlite, refers to flame-retardant materials with moderate smoke generation and with low index of flame spread on the surface.
- 3 August 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1122, 11-14
Heat-Reflecting Geocement Based Coatings Containing Perlite for Fire Protection of Timber
In this paper, the application of a heat-reflecting geocement coating, containing perlite, to reduce timber combustibility was studied. An optimized coating composition was prepared, which consisted of a geocement (Na2O·Al2O3·6SiO2·21.5H2O) and expanded perlite (9.5%). The main firing properties of this coating were invastigated. In terms of flammability, the fire protected timber reduces mass loss by 13 times and temperature of combustion gases by 5.2 times compared to unprotected timber. According to standard indicators, the reduction is by 1.3 and 10 times, respectively. The smoke generation of fire protected timber was decreased by 4.9 times (combustion mode) and 3.8 times (smoldering mode) in comparison to the unprotected timber. According to standard indicators, the decrease is by 4.5 and 2.3 times for each mode, respectively. The index of flame spread and the combustion rate reduced by 20.3 and 6.3 times, respectively, in the case of the fire protected timber compared to the unprotected one. The pine timber protected by heat-reflecting fireproofing geocement based coating, which contains perlite, refers to flame-retardant materials with moderate smoke generation and with low index of flame spread on the surface.
- Open Access
- 26 February 2015
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (5(73)) , 38-41
Determining the fire resistance properties of timber, protected by geocement-based coatings
Determining the fire resistance properties of timber, protected by geocement-based coatings
- 26 February 2015
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (5(73)) , 38-41
Open AccessDetermining the fire resistance properties of timber, protected by geocement-based coatings
Determining the fire resistance properties of timber, protected by geocement-based coatings
- 1 November 2013
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 838-841, 183-187
New Thermal Insulating Material Based on Geocement
A new thermal insulating material was developed on the basis of a geocement, formulated as Na2OAl2O36SiO220H2O. Ground limestone and aluminosilicate pellets were used as fillers for its production (composition: geocement 64.29 wt. [%]; fillers 35.71 wt. [%]). This material, which is applied having a thickness of 3.0-4.5 mm, swells when it is exposed to an external heat flow of 1273 K average temperature. Swelling is due to the matrix phases and filler dehydration, which include heulandite, ussingite, sodium zeolite and other phases. As a result, a finely porous glassy aluminosilicate frame of jadeite-albite composition is formed, which is characterized by low thermal conductivity (0.09-0.175 Wm-1K-1). The developed material can be used to protect and to insulate wooden, metal and concrete surfaces from an one-sided heat source.The paper is dedicated to the great scientist of the XXI century in the field of alkali-activated cements and materials based on them, Pavlo Kryvenko, in honor of his 75thbirthday anniversary.
- 1 November 2013
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 838-841, 183-187
New Thermal Insulating Material Based on Geocement
A new thermal insulating material was developed on the basis of a geocement, formulated as Na2OAl2O36SiO220H2O. Ground limestone and aluminosilicate pellets were used as fillers for its production (composition: geocement 64.29 wt. [%]; fillers 35.71 wt. [%]). This material, which is applied having a thickness of 3.0-4.5 mm, swells when it is exposed to an external heat flow of 1273 K average temperature. Swelling is due to the matrix phases and filler dehydration, which include heulandite, ussingite, sodium zeolite and other phases. As a result, a finely porous glassy aluminosilicate frame of jadeite-albite composition is formed, which is characterized by low thermal conductivity (0.09-0.175 Wm-1K-1). The developed material can be used to protect and to insulate wooden, metal and concrete surfaces from an one-sided heat source.The paper is dedicated to the great scientist of the XXI century in the field of alkali-activated cements and materials based on them, Pavlo Kryvenko, in honor of his 75thbirthday anniversary.
- 14 May 2013
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 688, 3-9
Protection of Timber from Combustion and Burning Using Alkaline Aluminosilicate-Based Coatings
The paper presents data on the protection of timber from combustion and burning using the protective coatings based on alkali aluminosilicates. The results of study suggested to formulate a mix design of the alkaline aluminosilicate bond, choose fillers and to determine rates of mass loss of timber at burning and degree to which the samples under study have been deteriorated. The coated samples of wood have a minimum rate of burning – 0.002-0.0024 kg/s·m2, which is 1.3-1.6 times less than the permissible value (0.0032 kg/s·m2) and 1.5-2.3 less than that of the analogue (a commercial product "Siofarb”). In combustibility and burning behavior, the formulated coatings can be classified as hardly combustible and non- burnable materials.
- 14 May 2013
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 688, 3-9
Protection of Timber from Combustion and Burning Using Alkaline Aluminosilicate-Based Coatings
The paper presents data on the protection of timber from combustion and burning using the protective coatings based on alkali aluminosilicates. The results of study suggested to formulate a mix design of the alkaline aluminosilicate bond, choose fillers and to determine rates of mass loss of timber at burning and degree to which the samples under study have been deteriorated. The coated samples of wood have a minimum rate of burning – 0.002-0.0024 kg/s·m2, which is 1.3-1.6 times less than the permissible value (0.0032 kg/s·m2) and 1.5-2.3 less than that of the analogue (a commercial product "Siofarb”). In combustibility and burning behavior, the formulated coatings can be classified as hardly combustible and non- burnable materials.