JMJoseph M. Mabry

Joseph M. Mabry

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Joseph M. Mabry has a total of 216 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Coalescence-induced jumping of droplets on superomniphobic surfaces with macrotexture

    by Hamed Vahabi, Wei Wang, Joseph M. Mabry, Arun K. Kota

    When two liquid droplets coalesce on a superrepellent surface, the excess surface energy is partly converted to upward kinetic energy, and the coalesced droplet jumps away from the surface. However, the efficiency of this energy conversion is very low. In this work, we used a simple and passive technique consisting of superomniphobic surfaces with a macrotexture (comparable to the droplet size) to experimentally demonstrate coalescence-induced jumping with an energy conversion efficiency of 18.8% (i.e., about 570% increase compared to superomniphobic surfaces without a macrotexture). The higher energy conversion efficiency arises primarily from the effective redirection of in-plane velocity vectors to out-of-plane velocity vectors by the macrotexture. Using this higher energy conversion efficiency, we demonstrated coalescence-induced jumping of droplets with low surface tension (26.6 mN m−1) and very high viscosity (220 mPa·s). These results constitute the first-ever demonstration of coalescence-induced jumping of droplets at Ohnesorge number >1.


  • Open Access

    Crystallographic analysis of analogous silicon- and carbon-containing di(cyanate ester)s and tri(cyanate ester)s

    by Kamran B. Ghiassi, Andrew J. Guenthner, Sean M. Ramirez, Michael D. Ford, Denisse Soto, Jerry A. Boatz, Joseph M. Mabry

  • Top Cited Papers
    Open Access

    Designing durable icephobic surfaces

    by Kevin Golovin, Sai P. R. Kobaku, Duck Hyun Lee, Edward T. DiLoreto, Joseph M. Mabry, Anish Tuteja

    Ice accretion has a negative impact on critical infrastructure, as well as a range of commercial and residential activities. Icephobic surfaces are defined by an ice adhesion strength τice < 100 kPa. However, the passive removal of ice requires much lower values of τice, such as on airplane wings or power lines (τice < 20 kPa). Such low τice values are scarcely reported, and robust coatings that maintain these low values have not been reported previously. We show that, irrespective of material chemistry, by tailoring the cross-link density of different elastomeric coatings and by enabling interfacial slippage, it is possible to systematically design coatings with extremely low ice adhesion (τice < 0.2 kPa). These newfound mechanisms allow for the rational design of icephobic coatings with virtually any desired ice adhesion strength. By using these mechanisms, we fabricate extremely durable coatings that maintain τice < 10 kPa after severe mechanical abrasion, acid/base exposure, 100 icing/deicing cycles, thermal cycling, accelerated corrosion, and exposure to Michigan wintery conditions over several months.


  • Structure-Property Relationships for Polycyanurate Networks Derived from Renewable Resources

    by Andrew J. Guenthner, Benjamin G. Harvey, Matthew C. Davis, Michael D. Ford, Heather A. Meylemans, Michael E. Wright, Andrew P. Chafin, Joseph M. Mabry, Schiraldi, Maiorana, et al.


  • Breakthrough Pressure as a Tool to Probe the Characteristics of Silicon-Containing Liquid-Repellent Surfaces (Briefing Charts)

    by Kevin T. Greeson, Andrew Guenthner, Raymond S. Campos, Joseph M. Mabry, Madani A. Khan, Jeffrey R. Alston

    Although the breakthrough pressure needed for liquids to penetrate re-entrant surface textures has been considered typically as simply a dependent parameter arising from the combination of geometry and thermodynamic interaction characteristics of the surface, it has the advantage of often being one of easiest parameters to determine experimentally with good precision. In fact, for many types of textures, including random media such as fibrous filters, or textures formed by growth or deposition of nanoparticles, it is far easier to quantify the breakthrough pressure than to quantify the geometry or the equilibrium contact angle. This presentation will explore the use of experimentally-determined breakthrough pressures (in combination with surface imaging and apparent contact angle measurements) to infer important geometric and thermodynamic characteristics of liquid repellent surfaces. Data are presented for two relevant examples, silicone coated phase separator membranes and silane-treated aluminum oxide nanograss textures.

  • Open Access

    Mechanisms of Decreased Moisture Uptake in Ortho-Methylated Di(cyanate ester) Networks

    by Andrew J. Guenthner, Michael E. Wright, Andrew P. Chafin, Josiah T. Reams, Kevin R. Lamison, Michael D. Ford, Shawn P. J. Kirby, Jacob J. Zavala, Joseph M. Mabry

    Decreases of up to 50% in the moisture uptake of polycyanurate networks based on 2,2-bis(4-cyanatophenyl)propane (BADCy) and 1,1-bis(4-cyanatophenyl)ethane (LECy) were observed when analogous networks containing a single methyl group ortho- to each aryl–cyanurate linkage were prepared by reduction and acid-catalyzed coupling of salicylic acid followed by treatment with cyanogen bromide and subsequent cyclotrimerization. The differences in water uptake were observed despite similar decreases in packing fraction as conversion proceeded in all networks studied. Conversely, the presence or absence of methyl groups at arylene bridges, remote from the cyanurate oxygen, had no influence on water uptake. Vitrification during cure had little effect on either free volume development or moisture uptake. These results confirm that steric hindrance from ortho-methyl groups inhibits absorption of water presumably by decreasing the thermodynamic favorability of sterically permitted interaction with the cyanurate oxygen. A further examination of the effect of two different catalysts, 2 parts per hundred of a 30:1 by weight mixture of nonylphenol and copper(II) acetylacetonate and 500 ppm of dibutyltin dilaurate (DBTDL), compared to analogous uncatalyzed networks, showed that hydrolytic stability was dramatically affected by catalyst choice, while thermochemical stability was also impacted. These results provide important insights into the mechanisms that determine structure–property relationships in polycyanurate networks.


  • Formulation and physical properties of cyanate ester nanocomposites based on graphene

    by Josiah T. Reams, Andrew J. Guenthner, Kevin R. Lamison, Gregory R. Yandek, David D. Swanson, Joseph M. Mabry

    We report the thermal, mechanical, and diffusion properties of bisphenol E based polycyanurate nanocomposites with three forms of graphene derived from sequential processing of the same carbon nanostructure. Edge‐functionalized graphene nanoplatelets (GNP) were converted to graphene oxide (GO), then heated to produce thermally reduced graphene oxide (TRGO). All three reinforcements were individually mixed with the dicyanate ester of bisphenol E (LECy) at low loading levels and cured to form polycyanurate nanocomposites. GNP, with very low oxygen functionality, was incompatible with the cyanate ester, while the highly oxidized GO formed well‐dispersed (though not exfoliated) nanocomposites, with the TRGO forming a good dispersion on mixing but phase separating during cure. The addition of GO, and, to a lesser extent, TRGO, resulted in improved mechanical properties, particularly fracture toughness, with the addition of TRGO having a modestly negative effect on the glass transition temperature. Surprisingly, neither GO nor TRGO addition was effective at slowing down the diffusion of water in the polycyanurate, with the addition of both resulting in increased equilibrium moisture uptake. It thus appears that the trade‐off between dispersion and the required level of oxygen functionality acts in a manner to frustrate attempts at minimizing the permeation of water by addition of graphene‐based reinforcements. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014, 52, 1061–1070


  • Pilot-scale coating of fabrics with fluorodecyl polyhedral oligomeric silsesquioxane/fluoroelastomer blends

    by Quoc Truong, Natalie Pomerantz, Pearl Yip, Michael Sieber, Joseph M. Mabry, Sean M. Ramirez

    A durable, conformal coating was developed based on the use of very low surface tension fluorodecyl polyhedral oligomeric silsesquioxane (Fluoro-POSS) cage-like molecule and a fluorinated elastomer. When this coating is applied, the resulting oleophobic fabrics resist surface wetting by a wide range of liquids having high to very low surface tension values, while remaining durable after repeated washing and abrasion testing. Collected data indicated minimal interference to air flow and moisture vapor through the conformally coated textiles. While textiles having said repellent treatment have been prepared previously by dip and spray coating in non-continuous laboratory applications, in 2012 the US Army Natick Research Development and Engineering Center successfully demonstrated a continuous, scalable application of Fluoro-POSS-treated textiles by way of a 24-inch-wide pad/dry/cure treatment. Material syntheses will be reported, and coating solution preparation and pilot-scale coating parameters will be discussed. Comparative data on surface, chemical and physical properties of lab-scale against pilot-scale coated repellent treated fabrics will be presented. These will include measurement of oleophobic coated fabrics’ contact angle using various liquids such as water and hazardous chemicals, as well as evaluation of chemical permeation test results and physical properties. Future work will examine the effects of different concentrations of low surface tension fluoropolymers and elastomers, hierarchical re-entrant nanostructures, and optimal processing and curing conditions.


  • Fluorinated Silsesquioxanes

    by Sean Ramirez, Joseph Mabry