ZSZhuochao Sun

Zhuochao Sun

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zhuochao Sun has a total of 17 co-authors. Here are the top co-authors by number of shared publications:

  • Liter Siek

    School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore 639798, Singapore

    16 shared publications
  • Howard Tang

    Nanyang technological university, Singapore, Singapore

    7 shared publications
  • Kin Wai Roy Chew

    VIRTUS, IC Design Centre of Excellence, Nanyang Technological University, Singapore

    6 shared publications
  • Guolei Yu

    VIRTUS, IC Design Centre of Excellence, Nanyang Technological University, Singapore

    2 shared publications
  • Chongfei Jin

    VIRTUS-IC Design Centre of Excellence, School of Electrical and Electronic Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798

    1 shared publication
  • M. Zhou

    VIRTUS‐IC Design Centre of Excellence, School of Electrical and Electronic Engineering Nanyang Technological University Singapore Singapore

    1 shared publication

Latest Publications

  • Open Access

    Fixed‐frequency hysteretic buck converter with novel adaptive window control and transient response improvement

    by Meng Jia, Zhuochao Sun, Liter Siek

    This study presents a fixed‐frequency hysteretic buck converter designed and fabricated using 0.18‐µm complementary metal–oxide–semiconductor process. With a phase‐locked loop (PLL)‐based adaptive window control, the proposed buck converter can achieve a fixed switching frequency, and this frequency can be tuned within a certain range through a reference clock frequency. Concurrently, a novel auxiliary circuit is proposed to monitor the converter's output loading dynamics to reduce the converter's transient recovery time. It will also help to regulate the output voltage at the steady‐state operation as well. With the supply voltage ranging from 3 to 4.2 V and an output voltage of 1.8 V, the simulated switching frequency is maintained at 10 MHz because of the PLL control. The transient response time is only 0.3 and 0.4 µs for a 400 mA step‐up load and step‐down load, respectively.


  • A Novel Zero-Voltage-Detector for Buck Converter in Discontinuous Conduction Mode(DCM)

    by Meng Jia, Zhuochao Sun, Liter Siek

    This paper presents a Zero-Voltage-Detector (ZVD) circuit for buck converters working in discontinuous conduction mode (DCM). A novel comparator with pre-amplification property is proposed to provide fast sensing and comparison to optimize the switching timing of power transistors, hence minimizing the power losses caused by the reverse inductor current. The proposed DCM buck converter is fabricated using 0.18um CMOS technology with a chip area of 0.9mm 2 . The simulated sensing delay of the proposed ZVD is only about 6ns. It achieves > 85% power efficiency for load currents of > 10mA when the input and output voltages are 3.3V and 2.4V respectively.


  • Multiloop Control for Fast Transient DC–DC Converter

    by Mi Zhou, Zhuochao Sun, Qiong Wei Low, Liter Siek

    A novel ac coupled feedback (ACCF) is proposed to alternatively realize fast transient response while inherently controlling the start-up in-rush current of a dc-dc switching converter. The proposed ACCF is modified from a conventional capacitor multiplier and connected between the outputs of the converter and the transconductance. With this supplemental feedback, the transient response has been significantly improved due to the gain-boosting effect around the compensator's midband. Moreover, the ACCF circuit assists to manage the ramping speed of the output voltage during power-up, thereby eliminating the bulky soft-start circuit. The new controller is very simple to implement and occupies a tiny footprint on-chip. A buck converter with the proposed scheme has been fabricated using the 0.18-μm standard CMOS process with an active silicon area of 0.573 mm 2 . Measurement results show that the output voltage rises linearly for a soft-start period of 1.05 ms according to the designed slope. Excellent load transient responses are achieved under different load current steps; the output voltage overshoot/undershoot of 60 mV settles down within 10 μs for a load variation from 50 μA to 1 A in 1 μs. Moreover, the proposed converter maintains both excellent load and line regulations of 0.018 mV/mA and 0.0056 mV/mV, respectively.


  • A Fast Transient Response DC-DC Converter with an Active Compensation Capacitor Module

    by Mi Zhou, Zhuochao Sun, Zhekai Xiao, Qiongwei Low, Liter Siek

    An active capacitor module is proposed to be implemented as a dynamic compensation capacitor at the output of the operational transconductance amplifier (OTA) to improve the load transient response of a DC-DC converter. To enhance the response speed during transient event, an active compensation capacitor module (ACM) is adopted to instantly reduce the capacitance of the compensation capacitor. Compared to the traditional approaches by increasing the transconductance gm of the OTA which introduce higher power consumption, the proposed ACM is more power efficient and it also occupies seven times smaller footprint than the large passive compensation capacitor in this work. A current-mode buck DC-DC converter with an ACM is implemented in 0.18 μim CMOS process and simulated across different process corners. Post-layout simulation results show an excellent load regulation of 0.008 mV/mA during load current variations from 50 μA to 1 A in 1 μs, and the proposed converter is working excellently under different load current steps. Output overshoot/undershoot voltages of 15 mV/22.8 mV with 5.9 μs/6 μs recovery time and 29.5 mV/47.5 mV with 8.8 μs/7.2 μs recovery time are obtained under 0.5 A load current step and 1 A load current step respectively from the simulation. Compared with the conventional converter without ACM, the output overshoot/undershoot voltage and recovery time are approximately reduced by twice and five times respectively.


  • A 1 V 103 dB 3rd-Order Audio Continuous-Time $\Delta \Sigma $ ADC With Enhanced Noise Shaping in 65 nm CMOS

    by Yoon Hwee Leow, Howard Tang, Zhuo Chao Sun, Liter Siek

    As technology scales, integrating high resolution ADCs into high fidelity mixed signal systems becomes challenging in advanced CMOS processes. Cascading integrators to achieve high-order filter structures limits the modulation index and compromises on stability at the expense of added hardware and power consumption. To optimize the maximum stable amplitude (MSA) to accommodate a larger input dynamic range, the supply rails have to be expanded, which limited technology choices to those of a larger feature size. This work proposes a 25 kHz 3rd-order continuous-time ΔΣ modulator (CTΔΣM) utilizing a 5-bit SAR quantizer, enabling noise coupling (NC) to be possible in a typical nanoscale CMOS 65 nm technology with VDD of 1 V. Mismatches in SAR comparator and DAC array are mitigated with a proposed calibration scheme while CM mismatches are solved by a floating differential charge storage capacitor (FDCSC) coupling method. To allow sufficient time for SAR bit cycling and noise charge feedback settling, 1 Ts excess loop delay (ELD) is compensated with digital differentiation that minimizes both the power and complexity of the auxiliary feedback DAC. The prototype obtained DR/SNR/SNDR of 103.1 dB/100.1 dB/95.2 dB while dissipating 0.8 mW, hence achieving a FoMSNDR and FoMschreier of 0.34 pJ/level and 177.9 dB, respectively.


  • Open Access

    Fast transient response DC–DC converter with start‐up in‐rush current control

    by M. Zhou, Z. Sun, Q. Low, L. Siek

    A new alternative to achieve fast transient response while inherently managing the in‐rush current during DC/DC switching converter start‐up is proposed. An AC coupled feedback (ACCF) is introduced using a capacitor multiplier from the output of the converter to the output of the error amplifier. With this additional feedback, the transient response, which used to be limited by the compensator mid‐band gain has been significantly improved. Meanwhile, the ACCF circuit can help to control the converter output ramping speed during power‐up, thus eliminating the bulky soft‐start circuit. The simplified circuit design means the new controller can be realised by a tiny on‐chip circuit, thereby minimising the footprint and the cost. A buck converter with the proposed technique is designed using 0.18 μm CMOS process and simulated across different process corners. Simulation shows that the output voltage increases linearly with the designed slope despite the variations of the input voltage, inductor or output capacitor values. An excellent load transient response of 0.021 mV/mA is achieved for a load current variation from 50 μA to 1 A in 1 μs.


  • A 400 nW Single-Inductor Dual-Input–Tri-Output DC–DC Buck–Boost Converter With Maximum Power Point Tracking for Indoor Photovoltaic Energy Harvesting

    by Guolei Yu, Kin Wai Roy Chew, Zhuo Chao Sun, Howard Tang, Liter Siek

    This paper presents a single-inductor dual-input- tri-output buck-boost (DITOBB) converter that manages energy harvesting, energy storage, and power rail regulation of an indoor remote sensor system. The converter operates in discontinuous conduction mode (DCM) and regulates the outputs with a combination of pulse-skipping modulation (PSM) and constant-ON-time pulse-frequency modulation (PFM). To reduce the quiescent power, all the circuit blocks are turned OFF when the outputs are within regulation, except a system clock generator. A newly designed relaxation oscillator provides the main clock of the system, which requires neither reference voltages nor comparators. The frequency of the system clock doubles or halves based on the states of the sources and outputs following a proposed algorithm. The DITOBB converter has been designed and fabricated using 0.18 μm CMOS process. With a quiescent power of 400 nW, the designed DITOBB converter shows a measured peak efficiency of 83% at 100 μW output power.


  • A 0.42-V Input Boost dc–dc Converter With Pseudo-Digital Pulsewidth Modulation

    by Zhuochao Sun, Kin Wai Roy Chew, Howard Tang, Guolei Yu, Liter Siek

    A pseudo-digital pulsewidth modulation (P-DPWM) controlled boost direct current-direct current converter is presented in this brief. By applying low-voltage analog design techniques into the traditional digital pulsewidth modulation (DPWM) structure, the proposed P-DPWM achieves new features of high resolution, low power, and small area while retaining the low-supply feature of the DPWM. A test chip has been designed and fabricated in a 65-nm CMOS process with an area of 1.44 mm 2 to validate its performance. A peak efficiency of 86% is achieved. The correct functionality is also demonstrated with the controller supply as low as 0.42 V, which is ideal for sub-1 V low-supply applications.


  • A Fixed-frequency hysteretic controlled buck DC-DC converter with improved load regulation

    by Zhuochao Sun, Liter Siek, Ravinder Pal Singh, Minkyu Je

    Hysteretic control is widely adopted in the power management units (PMUs) for modern electronic devices due to their simple and stable control architecture, as well as the fast load transient response. However, the switching frequency of a traditional hysteretic converter is not fixed. It changes with operating condition and component aging, and hence brings in electro-magnetic interference (EMI) problems and multiphase interleaving difficulties. In this work, a hysteretic buck converter with frequency-locking capability is presented, where the switching frequency is adjusted by tuning the hysteretic window. In addition, the current-mode hysteretic control in this work utilizes a simple feedback network, which consists of only passive components and yet provides significant improvement on output voltage regulation. To achieve good reliability at high temperature and high voltage, the proposed buck converter has been fabricated in a 1μm SOI process with a chip area of 6mm 2 . Experimental results measured at 1MHz fixed switching frequency with 12V-to-5V voltage conversion and 0.9A load current shows a peak efficiency of 91%.


  • A 1.33 $\mu{\rm W}$ 8.02-ENOB 100 kS/s Successive Approximation ADC With Supply Reduction Technique for Implantable Retinal Prosthesis

    by Howard Tang, Zhuo Chao Sun, Kin Wai Roy Chew, Liter Siek

    This paper presents a chip level 9 bits Charge Folding Successive-Approximation-Register (SAR) Analog-to-Digital Converter (ADC) to be used in a CMOS image sensor for retinal prosthesis. It has a maximum single-ended input range of 1.8 V but only uses a supply voltage of 0.9 V for the entire ADC through the Charge Folding method. Therefore, the input range is no longer limited by the supply rail as in conventional SAR ADC. Moreover, the ADC is controlled by an internal delay line based Asynchronous Clock Generator which can be programmed to adjust the resolution of the ADC from 5 to 9 bits. Therefore, resolution adaptation function can be applied to improve the energy efficiency up to 15%. The test chip is implemented in 0.18 μm CMOS process and occupies an area of 0.15 mm 2 . At 0.9 V and 100 kS/s, the 9 bit s ADC consumes 1.33 μW and achieves an energy efficiency of 51.3 fJ/conversion-step . In addition, the power consumption can be further reduced by scaling the supply voltage and sampling frequency. At 100 kS/s, this ADC is capable of converting the input signal at a rate equivalent to 30 frames/s for a pixel array up to 3200 pixels.