Andre Assmann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andre Assmann has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Adilson Luiz Chinelatto
State University of Ponta Grossa, Brazil
3 shared publications - Carlos Mauricio Lepienski
Postgraduate Program in Mechanical and Materials Engineering, Federal Technological University of Paraná, Campus Ecoville, Curitiba 81280-340, Brazil
3 shared publications - Carlos Eugenio Foerster
Departamento de Fıacute;sica, Universidade Estadual de Ponta Grossa, Ponta Grossa, Brazil
2 shared publications - Silvio Luiz Rutz da Silva
Universidade Estadual de Ponta Grossa
2 shared publications A R Jurelo
1 shared publicationA Somer
1 shared publication
Latest Publications
- 28 August 2014
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 47 (38)
Effects of thermal oxidation on the effective thermal diffusivity of titanium alloys
- 28 August 2014
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 47 (38)
Effects of thermal oxidation on the effective thermal diffusivity of titanium alloys
- 12 February 2013
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 113 (6) , 063507
Plasma nitriding process by direct current glow discharge at low temperature increasing the thermal diffusivity of AISI 304 stainless steel
This work reports for the first time on the use of the open photoacoustic cell technique operating at very low frequencies and at room temperature to experimentally determine the thermal diffusivity parameter of commercial AISI304 stainless steel and AISI304 stainless steel nitrided samples. Complementary measurements of X-ray diffraction and scanning electron microscopy were also performed. The results show that in standard AISI 304 stainless steel samples the thermal diffusivity is (4.0 ± 0.3) × 10−6 m2/s. After the nitriding process, the thermal diffusivity increases to the value (7.1 ± 0.5) × 10−6 m2/s. The results are being associated to the diffusion process of nitrogen into the surface of the sample. Carrying out subsequent thermal treatment at 500 °C, the thermal diffusivity increases up to (12.0 ± 2) × 10−6 m2/s. Now the observed growing in the thermal diffusivity must be related to the change in the phases contained in the nitrided layer.
- 12 February 2013
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 113 (6) , 063507
Plasma nitriding process by direct current glow discharge at low temperature increasing the thermal diffusivity of AISI 304 stainless steel
This work reports for the first time on the use of the open photoacoustic cell technique operating at very low frequencies and at room temperature to experimentally determine the thermal diffusivity parameter of commercial AISI304 stainless steel and AISI304 stainless steel nitrided samples. Complementary measurements of X-ray diffraction and scanning electron microscopy were also performed. The results show that in standard AISI 304 stainless steel samples the thermal diffusivity is (4.0 ± 0.3) × 10−6 m2/s. After the nitriding process, the thermal diffusivity increases to the value (7.1 ± 0.5) × 10−6 m2/s. The results are being associated to the diffusion process of nitrogen into the surface of the sample. Carrying out subsequent thermal treatment at 500 °C, the thermal diffusivity increases up to (12.0 ± 2) × 10−6 m2/s. Now the observed growing in the thermal diffusivity must be related to the change in the phases contained in the nitrided layer.
- 30 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 39 (11) , 3108-3114
Mechanical and Tribological Properties of LDX2101 Duplex Stainless Steel Submitted to Glow Discharge Ion Nitriding
In this paper, the mechanical and tribological properties of LDX2101 duplex stainless steel submitted to glow discharge (GD) nitriding and conventional ion beam nitrogen implantation (II) are reported. Different combinations of rich and poor nitrogen/hydrogen atmospheres and working GD temperatures are employed. Nitrogen II at room temperature and 350°C was performed at different energies and fluences in order to obtain a plateau distribution around 27 at.% until a depth of 400 nm. X-ray diffraction investigation indicated that the poor nitrogen atmosphere in GD processes is more efficient to produce expanded austenite and nitride precipitates at all temperatures. Nitrogen II, even at high temperature, produced only expanded austenite. The hardness of the nitrided surface region is about 18 GPa compared to ~ 3.3 GPa of the pristine condition. Wear resistance can be improved by one order of magnitude, independent of the GD nitrogen/hydrogen atmosphere, even at 300°C, where only expanded austenite is present.
- 30 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 39 (11) , 3108-3114
Mechanical and Tribological Properties of LDX2101 Duplex Stainless Steel Submitted to Glow Discharge Ion Nitriding
In this paper, the mechanical and tribological properties of LDX2101 duplex stainless steel submitted to glow discharge (GD) nitriding and conventional ion beam nitrogen implantation (II) are reported. Different combinations of rich and poor nitrogen/hydrogen atmospheres and working GD temperatures are employed. Nitrogen II at room temperature and 350°C was performed at different energies and fluences in order to obtain a plateau distribution around 27 at.% until a depth of 400 nm. X-ray diffraction investigation indicated that the poor nitrogen atmosphere in GD processes is more efficient to produce expanded austenite and nitride precipitates at all temperatures. Nitrogen II, even at high temperature, produced only expanded austenite. The hardness of the nitrided surface region is about 18 GPa compared to ~ 3.3 GPa of the pristine condition. Wear resistance can be improved by one order of magnitude, independent of the GD nitrogen/hydrogen atmosphere, even at 300°C, where only expanded austenite is present.
- 18 January 2010
- Published by Elsevier in Surface and Coatings Technology
- Vol. 204 (18-19) , 3004-3008
AISI 304 nitrocarburized at low temperature: Mechanical and tribological properties
- 18 January 2010
- Published by Elsevier in Surface and Coatings Technology
- Vol. 204 (18-19) , 3004-3008
AISI 304 nitrocarburized at low temperature: Mechanical and tribological properties
- 1 February 2009
- Published by Springer Nature in Journal of Materials Science
- Vol. 44 (4) , 1045-1053
Structural, mechanical, and tribological properties of AISI 304 and AISI 316L steels submitted to nitrogen–carbon glow discharge
- 1 February 2009
- Published by Springer Nature in Journal of Materials Science
- Vol. 44 (4) , 1045-1053
Structural, mechanical, and tribological properties of AISI 304 and AISI 316L steels submitted to nitrogen–carbon glow discharge