Meisam Goudarzy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Meisam Goudarzy has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Debdeep Sarkar
Chair of Soil Mechanics, Foundation Engineering and Environmental Geotechnics, Ruhr-Universität Bochum, Bochum, Germany
4 shared publications - Diethard König
Chair of Soil Mechanics, Foundation Engineering and Environmental Geotechnics, Ruhr-Universität Bochum, Bochum, Germany
4 shared publications - Torsten Wichtmann
Ruhr-Universität Bochum
3 shared publications - Houman Soleimani Fard
Keller - Middle East and Africa, PO Box 111323 , Dubai , UAE
2 shared publications - Masoud Ranjbarnia
Department of geotechnical Engineering, Faculty of civil engineering, University of Tabriz, Tabriz, Iran
2 shared publications - Milad Zaheri
Department of geotechnical Engineering, Faculty of civil engineering, University of Tabriz, Tabriz, Iran
2 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by Wiley in Structural Control and Health Monitoring
- Vol. 2026 (1)
State‐of‐the‐Art Review of Vibration‐Based Health Monitoring of Piles
Vibration‐based health monitoring (VHM) has emerged as a promising technique for assessing the integrity of deep foundations by interpreting variations in dynamic response governed by soil–pile interaction. This review presents the theoretical background of foundation failure mechanisms, sensing technologies, and numerical approaches that underpin VHM for pile foundations, with emphasis on recent advances in fiber‐optic sensing, piezoceramic transducers, and acoustic emission measurement. Developments in optimal sensor placement, high‐rate data acquisition, and advanced signal‐processing techniques including time‐ and frequency‐domain analysis and machine‐learning‐based interpretation are examined in relation to their capability to identify damage mechanisms such as cracking, scouring, buckling, degradation of bearing capacity and shaft resistance, and postearthquake damage. A critical evaluation of physical model tests, field studies, and numerical investigations highlights the strong influence of pile geometry, embedment depth, material type, excitation method, and sensor configuration on the sensitivity of vibration‐based indicators. While VHM has demonstrated strong potential during installation and under controlled monitoring conditions, its application to existing and aging foundations, particularly deeply embedded and large‐diameter piles, remains limited. The findings underscore the need for unified VHM protocols, scalable and nonintrusive sensing strategies, and field‐validated diagnostic indicators that explicitly account for soil–pile interaction to support reliable long‐term performance assessment of pile foundations, especially for postdisaster damage evaluation.
- 1 January 2026
- Published by Wiley in Structural Control and Health Monitoring
- Vol. 2026 (1)
Open AccessState‐of‐the‐Art Review of Vibration‐Based Health Monitoring of Piles
Vibration‐based health monitoring (VHM) has emerged as a promising technique for assessing the integrity of deep foundations by interpreting variations in dynamic response governed by soil–pile interaction. This review presents the theoretical background of foundation failure mechanisms, sensing technologies, and numerical approaches that underpin VHM for pile foundations, with emphasis on recent advances in fiber‐optic sensing, piezoceramic transducers, and acoustic emission measurement. Developments in optimal sensor placement, high‐rate data acquisition, and advanced signal‐processing techniques including time‐ and frequency‐domain analysis and machine‐learning‐based interpretation are examined in relation to their capability to identify damage mechanisms such as cracking, scouring, buckling, degradation of bearing capacity and shaft resistance, and postearthquake damage. A critical evaluation of physical model tests, field studies, and numerical investigations highlights the strong influence of pile geometry, embedment depth, material type, excitation method, and sensor configuration on the sensitivity of vibration‐based indicators. While VHM has demonstrated strong potential during installation and under controlled monitoring conditions, its application to existing and aging foundations, particularly deeply embedded and large‐diameter piles, remains limited. The findings underscore the need for unified VHM protocols, scalable and nonintrusive sensing strategies, and field‐validated diagnostic indicators that explicitly account for soil–pile interaction to support reliable long‐term performance assessment of pile foundations, especially for postdisaster damage evaluation.
- 3 January 2025
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 43 (2) , 1-22
Time-Dependent Tunnel Response: Analytical & Numerical Solutions for Nonlinear Post-Peak Behavior
- 3 January 2025
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 43 (2) , 1-22
Time-Dependent Tunnel Response: Analytical & Numerical Solutions for Nonlinear Post-Peak Behavior
- Open Access
- 28 February 2024
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 42 (5) , 3451-3469
On the Impact of Plastic Fines on the Compaction Characteristics of Sand
Binary mixtures of plastic fines and a non-cohesive host material are used in geotechnical barriers to obtain high shear strength and low permeability. To achieve such properties, the sand grains must form the force chain and the clay must fill the voids of the host material. However, clays are known to affect the grain to grain contacts by forming cohesive membranes. Since engineered barriers are usually compacted at water contents below saturation (Proctor conditions), it is still unclear whether such membranes will form. The aim of the current research is to shed light on the compaction characteristics of such mixtures. Proctor datasets were analysed in terms of skeleton and fines void ratio and optimal water content. Oedometric compression behaviour and limiting void ratios were studied to outline the characteristics of mixtures in a saturated or dry state, respectively. The results show that depending on the mixing ratio, compaction properties can be divided into three different ranges, where either the properties of one of the input materials dominate the behaviour or a transitional range exists that is characterised by a strong mutual influence of both materials. Furthermore, even a small amount of the highly plastic clay was found to influence the properties of the host sand.
- 28 February 2024
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 42 (5) , 3451-3469
Open AccessOn the Impact of Plastic Fines on the Compaction Characteristics of Sand
Binary mixtures of plastic fines and a non-cohesive host material are used in geotechnical barriers to obtain high shear strength and low permeability. To achieve such properties, the sand grains must form the force chain and the clay must fill the voids of the host material. However, clays are known to affect the grain to grain contacts by forming cohesive membranes. Since engineered barriers are usually compacted at water contents below saturation (Proctor conditions), it is still unclear whether such membranes will form. The aim of the current research is to shed light on the compaction characteristics of such mixtures. Proctor datasets were analysed in terms of skeleton and fines void ratio and optimal water content. Oedometric compression behaviour and limiting void ratios were studied to outline the characteristics of mixtures in a saturated or dry state, respectively. The results show that depending on the mixing ratio, compaction properties can be divided into three different ranges, where either the properties of one of the input materials dominate the behaviour or a transitional range exists that is characterised by a strong mutual influence of both materials. Furthermore, even a small amount of the highly plastic clay was found to influence the properties of the host sand.
- Open Access
- 1 January 2023
- Published by MDPI AG in Fractal and Fractional
- Vol. 7 (1) , 55
Editorial for Special Issue “Fractal and Fractional in Geomaterials”
Geomaterials, such as clay, sand, rockfill and ballast, etc
- 1 January 2023
- Published by MDPI AG in Fractal and Fractional
- Vol. 7 (1) , 55
Open AccessEditorial for Special Issue “Fractal and Fractional in Geomaterials”
Geomaterials, such as clay, sand, rockfill and ballast, etc
- 12 September 2022
- Published by Springer Nature in Granular Matter
- Vol. 24 (4) , 1-21
Small-strain shear modulus (Gmax) and microscopic pore structure of calcareous sand with different grain size distributions
- 12 September 2022
- Published by Springer Nature in Granular Matter
- Vol. 24 (4) , 1-21
Small-strain shear modulus (Gmax) and microscopic pore structure of calcareous sand with different grain size distributions
- Open Access
- 25 July 2022
- Published by Springer Nature in Acta Geotechnica
- Vol. 17 (11) , 4977-4988
Influence of plastic fines content on the liquefaction susceptibility of sands: cyclic loading
The paper presents an experimental study on the effect of plastic fines content on the undrained behavior and liquefaction susceptibility of sand-fines mixtures under cyclic loading. The results of undrained cyclic triaxial tests conducted on mixtures of Hostun sand with varying amounts (0–20%) and types (kaolin and calcigel bentonite) of plastic fines are presented. The specimens were prepared with different initial densities using the moist tamping method, consolidated at the same isotropic effective stress of 100 kPa and subjected to different deviatoric stress amplitudes. From the experimental observations, it was found that sand-clay mixtures with 10% or 20% clay content showed a lower cyclic liquefaction resistance than pure sand. Furthermore, the reduction in the cyclic stress ratio resulting in liquefaction after twenty cycles was found larger for sand-kaolin mixtures than for the sand-calcigel ones. Possible explanations are provided.
- 25 July 2022
- Published by Springer Nature in Acta Geotechnica
- Vol. 17 (11) , 4977-4988
Open AccessInfluence of plastic fines content on the liquefaction susceptibility of sands: cyclic loading
The paper presents an experimental study on the effect of plastic fines content on the undrained behavior and liquefaction susceptibility of sand-fines mixtures under cyclic loading. The results of undrained cyclic triaxial tests conducted on mixtures of Hostun sand with varying amounts (0–20%) and types (kaolin and calcigel bentonite) of plastic fines are presented. The specimens were prepared with different initial densities using the moist tamping method, consolidated at the same isotropic effective stress of 100 kPa and subjected to different deviatoric stress amplitudes. From the experimental observations, it was found that sand-clay mixtures with 10% or 20% clay content showed a lower cyclic liquefaction resistance than pure sand. Furthermore, the reduction in the cyclic stress ratio resulting in liquefaction after twenty cycles was found larger for sand-kaolin mixtures than for the sand-calcigel ones. Possible explanations are provided.
- 12 July 2022
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 55 (10) , 5879-5904
Analytical and Numerical Simulations to Predict the Long-Term Behavior of Lined Tunnels Considering Excavation-Induced Damaged Zone
- 12 July 2022
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 55 (10) , 5879-5904
Analytical and Numerical Simulations to Predict the Long-Term Behavior of Lined Tunnels Considering Excavation-Induced Damaged Zone
- Open Access
- 6 April 2022
- Published by MDPI AG in Fractal and Fractional
- Vol. 6 (4) , 205
Macro- and Micromechanical Assessment of the Influence of Non-Plastic Fines and Stress Anisotropy on the Dynamic Shear Modulus of Binary Mixtures
Resonant column tests were carried out on Hostun sand mixed with 5%, 10% and 20% non-plastic fines (defined as grains smaller than 0.075 mm) in order to quantify the combined influence of the void ratio (e), anisotropic stress state (defined as σv′/σh′) and fines content (fc) on the maximum small-strain shear modulus Gmax. A significant reduction in the Gmax with increasing fc was observed. Using the empirical model forwarded by Roesler, the influence of e and σv′/σh′ on Gmax was captured, although the model was unable to capture the influence of varying fines content using a single equation. From the micro-CT images, a qualitative observation of the initial skeletal structure of the ‘fines-in-sand’ grains was performed and the equivalent granular void ratio e* was determined. The e was henceforth replaced by e* in Roesler’s equation in order to capture the variation in fc. The new modification was quantified in terms of the mean square error R2. Furthermore, the Gmax of Hostun sand–fine mixtures was predicted with good accuracy by replacing e with e*. Additionally, a micromechanical interpretation based on the experimental observation was developed.
- 6 April 2022
- Published by MDPI AG in Fractal and Fractional
- Vol. 6 (4) , 205
Open AccessMacro- and Micromechanical Assessment of the Influence of Non-Plastic Fines and Stress Anisotropy on the Dynamic Shear Modulus of Binary Mixtures
Resonant column tests were carried out on Hostun sand mixed with 5%, 10% and 20% non-plastic fines (defined as grains smaller than 0.075 mm) in order to quantify the combined influence of the void ratio (e), anisotropic stress state (defined as σv′/σh′) and fines content (fc) on the maximum small-strain shear modulus Gmax. A significant reduction in the Gmax with increasing fc was observed. Using the empirical model forwarded by Roesler, the influence of e and σv′/σh′ on Gmax was captured, although the model was unable to capture the influence of varying fines content using a single equation. From the micro-CT images, a qualitative observation of the initial skeletal structure of the ‘fines-in-sand’ grains was performed and the equivalent granular void ratio e* was determined. The e was henceforth replaced by e* in Roesler’s equation in order to capture the variation in fc. The new modification was quantified in terms of the mean square error R2. Furthermore, the Gmax of Hostun sand–fine mixtures was predicted with good accuracy by replacing e with e*. Additionally, a micromechanical interpretation based on the experimental observation was developed.
- Open Access
- 28 July 2021
- Published by Springer Nature in Acta Geotechnica
- Vol. 17 (5) , 1719-1737
Influence of plastic fines content on the liquefaction susceptibility of sands: monotonic loading
The paper presents an experimental study on the effect of plastic fines content on the undrained behavior and liquefaction susceptibility of sand–fines mixtures under monotonic loading. The results of undrained monotonic triaxial compression tests conducted on mixtures of Hostun sand with varying amount (0–20%) and type (kaolin and calcigel bentonite) of plastic fines are presented. The specimens were prepared with different initial densities using the moist tamping method and consolidated at two different isotropic effective stresses. The results demonstrate that for both types of plastic fines, an increase in the fines content leads to a more contractive response and lower values of mobilized deviatoric stress. Despite similar relative density and fines content, the sand–kaolin mixtures showed a more contractive behavior than the sand–calcigel specimens. The steady-state lines (SSLs) ine–p´ space generally move downwards with increasing clay content. While the slopes of the SSLs for the clean Hostun sand and the mixtures with 10 and 20% kaolin are quite similar, the SSL lines for the specimens containing 10% or 20% calcigel run steeper or flatter, respectively. The inclination of the SSL in theq–p′ plane was found independent of clay type and content. The sand–kaolin mixtures were observed to be more susceptible to instability and flow liquefaction than the sand–calcigel mixtures.
- 28 July 2021
- Published by Springer Nature in Acta Geotechnica
- Vol. 17 (5) , 1719-1737
Open AccessInfluence of plastic fines content on the liquefaction susceptibility of sands: monotonic loading
The paper presents an experimental study on the effect of plastic fines content on the undrained behavior and liquefaction susceptibility of sand–fines mixtures under monotonic loading. The results of undrained monotonic triaxial compression tests conducted on mixtures of Hostun sand with varying amount (0–20%) and type (kaolin and calcigel bentonite) of plastic fines are presented. The specimens were prepared with different initial densities using the moist tamping method and consolidated at two different isotropic effective stresses. The results demonstrate that for both types of plastic fines, an increase in the fines content leads to a more contractive response and lower values of mobilized deviatoric stress. Despite similar relative density and fines content, the sand–kaolin mixtures showed a more contractive behavior than the sand–calcigel specimens. The steady-state lines (SSLs) ine–p´ space generally move downwards with increasing clay content. While the slopes of the SSLs for the clean Hostun sand and the mixtures with 10 and 20% kaolin are quite similar, the SSL lines for the specimens containing 10% or 20% calcigel run steeper or flatter, respectively. The inclination of the SSL in theq–p′ plane was found independent of clay type and content. The sand–kaolin mixtures were observed to be more susceptible to instability and flow liquefaction than the sand–calcigel mixtures.
- Open Access
- 7 June 2021
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 12 (1) , 1-19
Influence of surcharge on cone penetration test results and the inspection of various approaches for capturing its effect: a case study
Studies in recent decades demonstrate the significant effect of stress configuration (e.g., vertical stress and lateral confinement) on the shear strength or, in this study, the cone penetration test (CPT) results. Addition of a surcharge over the ground changes the stress condition, and consequently, the CPT tip resistance. In this study, the results of different CPTs conducted before and after backfilling with various thicknesses in a land development project were reviewed while focusing on the trend of an increase in CPT penetration resistance due to the additional surcharge. Both pre- to post-fill stress ratios and soil type affect the rise in corrected $${q}_{c}$$ values after backfilling. Moreover, there has always been a sudden increase in $${q}_{c}$$ values around the pre-fill surface in all studied cases. In this study, another approach was derived from the reanalysis of CPT data from a specific site for predicting the post-fill corrected $${q}_{c}$$ from pre-fill results by considering the above-mentioned factor. Likewise, post-fill results were predicted by depth-normalized pre-fill CPT results using Robertson’s normalization method. The proposed approach in this study showed a better match with the site data compared to the normalization method, especially at and around the pre-fill surface.- 7 June 2021
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 12 (1) , 1-19
Open AccessInfluence of surcharge on cone penetration test results and the inspection of various approaches for capturing its effect: a case study
Studies in recent decades demonstrate the significant effect of stress configuration (e.g., vertical stress and lateral confinement) on the shear strength or, in this study, the cone penetration test (CPT) results. Addition of a surcharge over the ground changes the stress condition, and consequently, the CPT tip resistance. In this study, the results of different CPTs conducted before and after backfilling with various thicknesses in a land development project were reviewed while focusing on the trend of an increase in CPT penetration resistance due to the additional surcharge. Both pre- to post-fill stress ratios and soil type affect the rise in corrected $${q}_{c}$$ values after backfilling. Moreover, there has always been a sudden increase in $${q}_{c}$$ values around the pre-fill surface in all studied cases. In this study, another approach was derived from the reanalysis of CPT data from a specific site for predicting the post-fill corrected $${q}_{c}$$ from pre-fill results by considering the above-mentioned factor. Likewise, post-fill results were predicted by depth-normalized pre-fill CPT results using Robertson’s normalization method. The proposed approach in this study showed a better match with the site data compared to the normalization method, especially at and around the pre-fill surface.