Amélia Severino Ferreira Santos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Amélia Severino Ferreira Santos has a total of 128 co-authors. Here are the top co-authors by number of shared publications:
Eliton S. Medeiros
Laboratory of Materials and Biosystems (LAMAB), Federal University of Paraiba (UFPB) , Campus I, 58051-900 , João Pessoa , PB , Brazil
8 shared publications- Juliano Elvis Oliveira
Federal University of Lavras
6 shared publications Eliton S Medeiros
Laboratory of Materials and Biosystems, Department of Materials Engineering, Federal University of Paraiba – UFPB, Brazil
4 shared publications- Eliton Souto Medeiros
Federal University of Paraíba
4 shared publications - Mauricio Pinheiro Oliveira
Laboratory of Polymer Synthesis and Process, Institute of Science and Technology, Federal University of São Paulo (UNIFESP), São José dos Campos, São Paulo 12231-280, Brazil
4 shared publications Neymara C. Nepomuceno
3 shared publications
Latest Publications
- 27 August 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (42) , e71417
Simvastatin‐Loaded PLA / PEG Nanofibers Produced by Solution Blow Spinning: Formulation, Characterization, and in Vitro Cytotoxicity
Simvastatin (SIM)‐loaded poly(L,D‐lactic acid) (PLA) and poly(ethylene glycol) (PEG) fibrous mats were fabricated via Solution Blow Spinning (SBS) as functional platforms for controlled local drug delivery. Scaffolds with PLA/PEG weight ratios 100:0, 90:10, 80:20, and 70:30 (15 wt.% total polymer) were prepared incorporating 2.5 wt.% SIM. The fibrous mats were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), x‐ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), water contact angle measurements, in vitro SIM release over 21 days (UV–Vis), and cell cytotoxicity assays. Smooth, defect‐free, and uniform cylindrical fibers were obtained for all compositions, achieving high encapsulation efficiencies (> 89%). The incorporation of PEG reduced average fiber diameters, enhanced matrix wettability, and modulated the drug release profiles. Mathematical modeling revealed a key transition in drug transport mechanisms: lower PEG content formulations (PLA 10 ‐2.5 and PLA 20 ‐2.5) were governed by concentration‐dependent First‐Order kinetics ( r 2 ≥ 0.909), whereas the PLA 30 ‐2.5 matrix attained ideal Zero‐Order kinetics ( r 2 = 0.978), delivering a constant and sustained drug release. Furthermore, all scaffolds maintained high cytocompatibility. Overall, tuning the PLA/PEG blend ratio allows precise control over release kinetics, demonstrating the potential of these PLA/PEG/SIM mats as versatile platforms for localized biomedical applications.
- 27 August 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (42) , e71417
Simvastatin‐Loaded PLA / PEG Nanofibers Produced by Solution Blow Spinning: Formulation, Characterization, and in Vitro Cytotoxicity
Simvastatin (SIM)‐loaded poly(L,D‐lactic acid) (PLA) and poly(ethylene glycol) (PEG) fibrous mats were fabricated via Solution Blow Spinning (SBS) as functional platforms for controlled local drug delivery. Scaffolds with PLA/PEG weight ratios 100:0, 90:10, 80:20, and 70:30 (15 wt.% total polymer) were prepared incorporating 2.5 wt.% SIM. The fibrous mats were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), x‐ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), water contact angle measurements, in vitro SIM release over 21 days (UV–Vis), and cell cytotoxicity assays. Smooth, defect‐free, and uniform cylindrical fibers were obtained for all compositions, achieving high encapsulation efficiencies (> 89%). The incorporation of PEG reduced average fiber diameters, enhanced matrix wettability, and modulated the drug release profiles. Mathematical modeling revealed a key transition in drug transport mechanisms: lower PEG content formulations (PLA 10 ‐2.5 and PLA 20 ‐2.5) were governed by concentration‐dependent First‐Order kinetics ( r 2 ≥ 0.909), whereas the PLA 30 ‐2.5 matrix attained ideal Zero‐Order kinetics ( r 2 = 0.978), delivering a constant and sustained drug release. Furthermore, all scaffolds maintained high cytocompatibility. Overall, tuning the PLA/PEG blend ratio allows precise control over release kinetics, demonstrating the potential of these PLA/PEG/SIM mats as versatile platforms for localized biomedical applications.
- Open Access
- 6 August 2026
- Published by Elsevier in Materials Today Communications
- Vol. 55
Active cellulosic packaging based on fully renewable resources: Paper coating by solution blow spraying
- 6 August 2026
- Published by Elsevier in Materials Today Communications
- Vol. 55
Open AccessActive cellulosic packaging based on fully renewable resources: Paper coating by solution blow spraying
- Open Access
- 23 June 2026
- Published by Springer Nature in Cellulose
- p. 1-26
Producing well-dispersed cellulose nanocrystals (CNCs) in poly(lactic acid) (PLA)
Bionanocomposites from renewable sources that can replace petroleum-based plastics at comparable cost represent a significant current challenge. In this context, the authors proposed using coconut oil (CO) as a spacer for cellulose nanocrystals (CNC). This method aims to hinder hornification during CNC drying and improve its redispersion in poly(lactic acid) (PLA). With this goal, an oven-dried CNC masterbatch dispersed in coconut oil (CNC/xCO)m, free of water and residual organic solvents, was prepared by solvent exchange to ethyl alcohol (CNCa). This mixture is ready for use in any PLA/CNC nanocomposite processing route at lower cost than CNC powder produced by freeze-drying. Films of neat PLA; PLA with 3 phr of never-dried CNCs, prepared by solvent exchange to chloroform (PLA/3CNCc); PLA with 3 phr (PLA/3CO) and 12 phr of CO (PLA/12CO); and PLA/(3CNC/xCO)m at 1:1 and 1:4 ratios were prepared by solvent casting. Afterwards, these films were characterized by Fourier-transform infrared spectroscopy (FTIR), light transmittance, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), field-emission scanning electron microscopy (FESEM), contact angle, and tensile testing. FESEM images showed that PLA/(3CNC/xCO)m achieved better CNC dispersion than PLA/3CNCc. However, the droplet-shaped morphology of CO produced a discontinuous PLA matrix. As a result, PLA/(3CNC/xCO)m had lower mechanical performance than PLA/3CNCc. The attempt to inhibit hornification of CNCs during drying by using CO as spacers was hindered by the effects of CO’s droplet morphology in the brittle polymer matrix. Regardless of that, this new route produced a CNC masterbatch free of moisture, and ready for redispersion by any polymer processing method. This study is a step forward in developing a competitive, clean technology for producing CNC nanocomposites in hydrophobic matrices.
- 23 June 2026
- Published by Springer Nature in Cellulose
- p. 1-26
Open AccessProducing well-dispersed cellulose nanocrystals (CNCs) in poly(lactic acid) (PLA)
Bionanocomposites from renewable sources that can replace petroleum-based plastics at comparable cost represent a significant current challenge. In this context, the authors proposed using coconut oil (CO) as a spacer for cellulose nanocrystals (CNC). This method aims to hinder hornification during CNC drying and improve its redispersion in poly(lactic acid) (PLA). With this goal, an oven-dried CNC masterbatch dispersed in coconut oil (CNC/xCO)m, free of water and residual organic solvents, was prepared by solvent exchange to ethyl alcohol (CNCa). This mixture is ready for use in any PLA/CNC nanocomposite processing route at lower cost than CNC powder produced by freeze-drying. Films of neat PLA; PLA with 3 phr of never-dried CNCs, prepared by solvent exchange to chloroform (PLA/3CNCc); PLA with 3 phr (PLA/3CO) and 12 phr of CO (PLA/12CO); and PLA/(3CNC/xCO)m at 1:1 and 1:4 ratios were prepared by solvent casting. Afterwards, these films were characterized by Fourier-transform infrared spectroscopy (FTIR), light transmittance, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), field-emission scanning electron microscopy (FESEM), contact angle, and tensile testing. FESEM images showed that PLA/(3CNC/xCO)m achieved better CNC dispersion than PLA/3CNCc. However, the droplet-shaped morphology of CO produced a discontinuous PLA matrix. As a result, PLA/(3CNC/xCO)m had lower mechanical performance than PLA/3CNCc. The attempt to inhibit hornification of CNCs during drying by using CO as spacers was hindered by the effects of CO’s droplet morphology in the brittle polymer matrix. Regardless of that, this new route produced a CNC masterbatch free of moisture, and ready for redispersion by any polymer processing method. This study is a step forward in developing a competitive, clean technology for producing CNC nanocomposites in hydrophobic matrices.
- Open Access
- 4 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (3) , 2097-2107
Synthesis and Characterization of Biobased Poly(farnesene- co -IBOMA) via Emulsion Polymerization Technique for Barrier Paper Coating Application
- 4 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (3) , 2097-2107
Open AccessSynthesis and Characterization of Biobased Poly(farnesene- co -IBOMA) via Emulsion Polymerization Technique for Barrier Paper Coating Application
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Engenharia Sanitaria e Ambiental
- Vol. 31
Sustainable compressed earth blocks: use of polymeric waste composed of polypropylene/polyethylene waste and expanded polystyrene
This study investigates the mechanical strength of compressed earth blocks (CEBs) incorporating varying percentages of polypropylene/polyethylene (PP/PE) up to 30%, and expanded polystyrene (EPS) up to 7.5%, residues across different curing periods (7, 14, and 28 days). Statistical analysis was performed to evaluate the effects of soil composition and residue content on flexural strength, including a multi-factor Analysis of Variance (ANOVA). The results showed that both soil (A and B) types (p < 0.001) and residue content (p = 0.000) significantly influenced the blocks’ strength, while curing time did not have a significant effect (p = 0.637). The type of polymeric residue also had a significant impact, as the flexural strength of blocks with EPS was significantly higher than those with PP/PE (p = 0.002). Specifically, the T2 soil formulation, which contained 80% of Soil B, resulted in a significantly lower tensile strength compared to the T0 and T1 formulations (p < 0.001 and p = 0.020, respectively). Furthermore, the inclusion of 30% PP/PE residue led to a significant reduction in strength, while the addition of 5% and 7.5% EPS residue resulted in a significant increase in flexural strength. These findings highlight the critical role of material formulation in the development of sustainable construction materials.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Engenharia Sanitaria e Ambiental
- Vol. 31
Open AccessSustainable compressed earth blocks: use of polymeric waste composed of polypropylene/polyethylene waste and expanded polystyrene
This study investigates the mechanical strength of compressed earth blocks (CEBs) incorporating varying percentages of polypropylene/polyethylene (PP/PE) up to 30%, and expanded polystyrene (EPS) up to 7.5%, residues across different curing periods (7, 14, and 28 days). Statistical analysis was performed to evaluate the effects of soil composition and residue content on flexural strength, including a multi-factor Analysis of Variance (ANOVA). The results showed that both soil (A and B) types (p < 0.001) and residue content (p = 0.000) significantly influenced the blocks’ strength, while curing time did not have a significant effect (p = 0.637). The type of polymeric residue also had a significant impact, as the flexural strength of blocks with EPS was significantly higher than those with PP/PE (p = 0.002). Specifically, the T2 soil formulation, which contained 80% of Soil B, resulted in a significantly lower tensile strength compared to the T0 and T1 formulations (p < 0.001 and p = 0.020, respectively). Furthermore, the inclusion of 30% PP/PE residue led to a significant reduction in strength, while the addition of 5% and 7.5% EPS residue resulted in a significant increase in flexural strength. These findings highlight the critical role of material formulation in the development of sustainable construction materials.
- 12 June 2024
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 39 (4) , 477-489
Evaluation of the processing conditions on the production of expanded or plasticized wood plastic composite with cashew nutshell powder
In this work we investigate the influence of closed (“C”) or open (“O”) extrusion degassing, and low (5 MPa – “L”) or high (90 MPa – “H”) holding pressure during injection molding on the properties of wood-plastic composite (WPC) based on high-density polyethylene (HDPE) flakes compatibilized with 5 wt% maleic anhydride-modified polyethylene (MAPE), 5 wt% lubricant (Struktol® TPW 113), and 40 wt% cashew nutshell powder (CNSP). Two reference compounds were extruded with closed degassing and injected at 90 MPa of holding pressure: (1) HDPE flakes extruded with 5 wt% MAPE and 5 wt% Struktol® TPW 113 (HDPEad_C-H) and (2) HDPE flakes previously melt mixed in an internal mixer with 5 wt% CNSL (HDPEr/5CNSL) and then extruded with the same additive content (HDPEad/5CNSL_C-H). At 90 MPa holding pressure, the extract content of WPC slightly increased and CNSL acted as a lubricant and poor plasticizing agent, reducing the crystallinity and density of the additivated matrix (HDPEad_C-H), increasing the flow rate without significantly changing the tensile strength. On the other hand, low holding pressure (5 MPa) favored the volatilization and expansion of the residual CNSL in the WPC, which acted as a blowing agent improving filling of the mold cavity and avoiding sink marks. Sample extruded with open degassing (atmospheric pressure) did not significantly change the extract content, but favored CNSL diffusion from particles to matrix, which subsequently during injection molding led to its entrapment at the interface, resulting in low adhesion, especially at high holding pressure that hinders CNSL expansion and vaporization. These findings contribute to understand the role of residual CNSL of CNSP in WPC properties and thus, to strengthen the plastics recycling chain and reduce carbon footprint.
- 12 June 2024
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 39 (4) , 477-489
Evaluation of the processing conditions on the production of expanded or plasticized wood plastic composite with cashew nutshell powder
In this work we investigate the influence of closed (“C”) or open (“O”) extrusion degassing, and low (5 MPa – “L”) or high (90 MPa – “H”) holding pressure during injection molding on the properties of wood-plastic composite (WPC) based on high-density polyethylene (HDPE) flakes compatibilized with 5 wt% maleic anhydride-modified polyethylene (MAPE), 5 wt% lubricant (Struktol® TPW 113), and 40 wt% cashew nutshell powder (CNSP). Two reference compounds were extruded with closed degassing and injected at 90 MPa of holding pressure: (1) HDPE flakes extruded with 5 wt% MAPE and 5 wt% Struktol® TPW 113 (HDPEad_C-H) and (2) HDPE flakes previously melt mixed in an internal mixer with 5 wt% CNSL (HDPEr/5CNSL) and then extruded with the same additive content (HDPEad/5CNSL_C-H). At 90 MPa holding pressure, the extract content of WPC slightly increased and CNSL acted as a lubricant and poor plasticizing agent, reducing the crystallinity and density of the additivated matrix (HDPEad_C-H), increasing the flow rate without significantly changing the tensile strength. On the other hand, low holding pressure (5 MPa) favored the volatilization and expansion of the residual CNSL in the WPC, which acted as a blowing agent improving filling of the mold cavity and avoiding sink marks. Sample extruded with open degassing (atmospheric pressure) did not significantly change the extract content, but favored CNSL diffusion from particles to matrix, which subsequently during injection molding led to its entrapment at the interface, resulting in low adhesion, especially at high holding pressure that hinders CNSL expansion and vaporization. These findings contribute to understand the role of residual CNSL of CNSP in WPC properties and thus, to strengthen the plastics recycling chain and reduce carbon footprint.
- Open Access
- 1 January 2024
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 12 (12) , 1-10
Effect of Concentration and Residence Time of Joncryl®ADR4368 on Melt Processability of Poly(3-hydroxybutyrate)
Poly(3-hydroxybutyrate) (PHB) is a biothechnological and biodegradable thermoplastic polymer from the polyhydroxyalkanoates (PHAs) family, whose chain regularity, high molecular weight, and physical and mechanical properties ... | Find, read and cite all the research you need on Tech Science Press
- 1 January 2024
- Published by Tech Science Press in Journal of Renewable Materials
- Vol. 12 (12) , 1-10
Open AccessEffect of Concentration and Residence Time of Joncryl®ADR4368 on Melt Processability of Poly(3-hydroxybutyrate)
Poly(3-hydroxybutyrate) (PHB) is a biothechnological and biodegradable thermoplastic polymer from the polyhydroxyalkanoates (PHAs) family, whose chain regularity, high molecular weight, and physical and mechanical properties ... | Find, read and cite all the research you need on Tech Science Press
- 1 November 2023
- Published by Springer Nature in Cellulose
- Vol. 30 (18) , 11455-11472
Evaluation of the kinetics of low intensity ultrasound-assisted sulfuric acid hydrolysis to obtain cellulose nanocrystals (CNCs) from microcrystalline cellulose (MCC)
- 1 November 2023
- Published by Springer Nature in Cellulose
- Vol. 30 (18) , 11455-11472
Evaluation of the kinetics of low intensity ultrasound-assisted sulfuric acid hydrolysis to obtain cellulose nanocrystals (CNCs) from microcrystalline cellulose (MCC)
- 17 January 2023
- Published by SAGE Publications in Progress in Rubber, Plastics and Recycling Technology
- Vol. 39 (3) , 250-263
Characterization of adhesive content in post-consumer poly(ethylene terephthalate) bottles and assessment of its impact on poly(ethylene terephthalate) recyclability
Although the consequences of adhesive residues from post-consumer Poly(ethylene terephthalate) (PET) beverage bottles on the performance of recycled products are known, the quantitative effects of these adhesives are not well-stablished in the literature. Therefore, these residues were determined by gravimetry, and the adhesive content range from 200 to 2800 ppm in post-consumer PET bottles, depending on the drink filled. Through FTIR analysis, it was determined that the adhesives for bottles labelling are composed by poly(ethylene- co-vinyl acetate) (EVA). Based on these results, recycled PET with 0, 200, 700, 1500 and 3000 ppm of hot-melt EVA were processed in an internal mixer connected to a torque rheometer at 265°C for 10 min. Tensile tests indicate that 200 ppm of adhesive reduced PET tensile strength by 15%. Furthermore, when about 1500 ppm of adhesive is present, PET mechanical properties are reduced by 50%. Therefore, it is of utmost importance to warn the PET bottle production chain to reduce adhesive content used in labelling so that it should not exceed 200 ppm, if a high quality recycled PET is desirable.
- 17 January 2023
- Published by SAGE Publications in Progress in Rubber, Plastics and Recycling Technology
- Vol. 39 (3) , 250-263
Characterization of adhesive content in post-consumer poly(ethylene terephthalate) bottles and assessment of its impact on poly(ethylene terephthalate) recyclability
Although the consequences of adhesive residues from post-consumer Poly(ethylene terephthalate) (PET) beverage bottles on the performance of recycled products are known, the quantitative effects of these adhesives are not well-stablished in the literature. Therefore, these residues were determined by gravimetry, and the adhesive content range from 200 to 2800 ppm in post-consumer PET bottles, depending on the drink filled. Through FTIR analysis, it was determined that the adhesives for bottles labelling are composed by poly(ethylene- co-vinyl acetate) (EVA). Based on these results, recycled PET with 0, 200, 700, 1500 and 3000 ppm of hot-melt EVA were processed in an internal mixer connected to a torque rheometer at 265°C for 10 min. Tensile tests indicate that 200 ppm of adhesive reduced PET tensile strength by 15%. Furthermore, when about 1500 ppm of adhesive is present, PET mechanical properties are reduced by 50%. Therefore, it is of utmost importance to warn the PET bottle production chain to reduce adhesive content used in labelling so that it should not exceed 200 ppm, if a high quality recycled PET is desirable.
- 1 December 2022
- Published by Springer Nature in Polymer Bulletin
- Vol. 80 (10) , 11363-11377
Biodegradation of PLA/CNC composite modified with non-ionic surfactants
- 1 December 2022
- Published by Springer Nature in Polymer Bulletin
- Vol. 80 (10) , 11363-11377
Biodegradation of PLA/CNC composite modified with non-ionic surfactants