Jon Eggert Carlé
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jon Eggert Carlé has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Frederik Christian Krebs
Department of Energy Conversion and Storage Technical University of Denmark Frederiksborgvej 399 4000 Roskilde Denmark
34 shared publications - Martin Helgesen
Department of Energy Conversion and Storage Technical University of Denmark Frederiksborgvej 399 DK‐4000 Roskilde Denmark
26 shared publications - Mikkel Jørgensen
Department of Energy Conversion and Storage, Technical University of Denmark, Frederiksborgvej 399, DK-4000, Roskilde, Denmark
19 shared publications - Eva Bundgaard
Department of Energy Conversion and Storage, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde, Denmark
17 shared publications - Roar R. Sondergaard
Technical University of Denmark
14 shared publications Thomas R. Andersen
Department of Energy Conversion and Storage Technical University of Denmark Frederiksborgvej 399 4000 Roskilde Denmark
7 shared publications
Latest Publications
- 13 October 2017
- Published by Wiley in Macromolecular Rapid Communications
- Vol. 38 (22)
Conjugated Polymers Via Direct Arylation Polymerization in Continuous Flow: Minimizing the Cost and Batch‐to‐Batch Variations for High‐Throughput Energy Conversion
Continuous flow methods are utilized in conjunction with direct arylation polymerization (DArP) for the scaled synthesis of the roll‐to‐roll compatible polymer, poly[(2,5‐bis(2‐hexyldecyloxy)phenylene)‐alt‐(4,7‐di(thiophen‐2‐yl)‐benzo[c][1,2,5]thiadiazole)] (PPDTBT). PPDTBT is based on simple, inexpensive, and scalable monomers using thienyl‐flanked benzothiadiazole as the acceptor, which is the first β‐unprotected substrate to be used in continuous flow via DArP, enabling critical evaluation of the suitability of this emerging synthetic method for minimizing defects and for the scaled synthesis of high‐performance materials. To demonstrate the usefulness of the method, DArP‐prepared PPDTBT via continuous flow synthesis is employed for the preparation of indium tin oxide (ITO)‐free and flexible roll‐coated solar cells to achieve a power conversion efficiency of 3.5% for 1 cm2 devices, which is comparable to the performance of PPDTBT polymerized through Stille cross coupling. These efforts demonstrate the distinct advantages of the continuous flow protocol with DArP avoiding use of toxic tin chemicals, reducing the associated costs of polymer upscaling, and minimizing batch‐to‐batch variations for high‐quality material.
- 13 October 2017
- Published by Wiley in Macromolecular Rapid Communications
- Vol. 38 (22)
Conjugated Polymers Via Direct Arylation Polymerization in Continuous Flow: Minimizing the Cost and Batch‐to‐Batch Variations for High‐Throughput Energy Conversion
Continuous flow methods are utilized in conjunction with direct arylation polymerization (DArP) for the scaled synthesis of the roll‐to‐roll compatible polymer, poly[(2,5‐bis(2‐hexyldecyloxy)phenylene)‐alt‐(4,7‐di(thiophen‐2‐yl)‐benzo[c][1,2,5]thiadiazole)] (PPDTBT). PPDTBT is based on simple, inexpensive, and scalable monomers using thienyl‐flanked benzothiadiazole as the acceptor, which is the first β‐unprotected substrate to be used in continuous flow via DArP, enabling critical evaluation of the suitability of this emerging synthetic method for minimizing defects and for the scaled synthesis of high‐performance materials. To demonstrate the usefulness of the method, DArP‐prepared PPDTBT via continuous flow synthesis is employed for the preparation of indium tin oxide (ITO)‐free and flexible roll‐coated solar cells to achieve a power conversion efficiency of 3.5% for 1 cm2 devices, which is comparable to the performance of PPDTBT polymerized through Stille cross coupling. These efforts demonstrate the distinct advantages of the continuous flow protocol with DArP avoiding use of toxic tin chemicals, reducing the associated costs of polymer upscaling, and minimizing batch‐to‐batch variations for high‐quality material.
- 28 September 2017
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 10 (11) , 2411-2419
In-line, roll-to-roll morphology analysis of organic solar cell active layers
We present the first comparative in situ small and wide angle X-ray scattering study of two polymers that are relevant for organic photovoltaics, during coating on a flexible substrate. From the obtained measurements we identified several differences between the drying of the two polymers. The polymer optimized for roll-to-roll coating attained its final morphological packing nearly instantly after deposition, and had the shortest drying profile. We therefore conclude that fast-drying polymers which are influenced less by drying temperature or substrate inhomogeneities are better suited for roll-to-roll coating, and that fundamentally, the kinetics of drying dominate the process in the case of roll-to-roll slot-die coating.
- 28 September 2017
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 10 (11) , 2411-2419
In-line, roll-to-roll morphology analysis of organic solar cell active layers
We present the first comparative in situ small and wide angle X-ray scattering study of two polymers that are relevant for organic photovoltaics, during coating on a flexible substrate. From the obtained measurements we identified several differences between the drying of the two polymers. The polymer optimized for roll-to-roll coating attained its final morphological packing nearly instantly after deposition, and had the shortest drying profile. We therefore conclude that fast-drying polymers which are influenced less by drying temperature or substrate inhomogeneities are better suited for roll-to-roll coating, and that fundamentally, the kinetics of drying dominate the process in the case of roll-to-roll slot-die coating.
- 23 May 2016
- Published by Wiley in Advanced Engineering Materials
- Vol. 18 (8) , 1494-1503
Slot‐Die‐Coated V2O5 as Hole Transport Layer for Flexible Organic Solar Cells and Optoelectronic Devices
Vanadium pentoxide has been proposed as a good alternative hole transport layer for improving device lifetime of organic photovoltaics. The article presents a study on the optimization of slot‐die‐coated vanadium oxide films produced with a roll coating machine with the aim of achieving scalable organic solar cells and photo‐detectors with improved performance. The effect of different diluents on the electrical properties of the vanadium oxide films is investigated, and methodologies for efficient interfacing of the anode are studied. Furthermore, the lifetime of the cells with incorporated vanadium oxide is investigated employing different encapsulation methods. Finally, an application of the manufactured scalable devices in proximity sensors is demonstrated using a 3D‐printed scaffold.
- 23 May 2016
- Published by Wiley in Advanced Engineering Materials
- Vol. 18 (8) , 1494-1503
Slot‐Die‐Coated V2O5 as Hole Transport Layer for Flexible Organic Solar Cells and Optoelectronic Devices
Vanadium pentoxide has been proposed as a good alternative hole transport layer for improving device lifetime of organic photovoltaics. The article presents a study on the optimization of slot‐die‐coated vanadium oxide films produced with a roll coating machine with the aim of achieving scalable organic solar cells and photo‐detectors with improved performance. The effect of different diluents on the electrical properties of the vanadium oxide films is investigated, and methodologies for efficient interfacing of the anode are studied. Furthermore, the lifetime of the cells with incorporated vanadium oxide is investigated employing different encapsulation methods. Finally, an application of the manufactured scalable devices in proximity sensors is demonstrated using a 3D‐printed scaffold.
- 24 March 2016
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 28 (7) , 2363-2373
Mechanical Properties of a Library of Low-Band-Gap Polymers
- 24 March 2016
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 28 (7) , 2363-2373
Mechanical Properties of a Library of Low-Band-Gap Polymers
- Open Access
- 1 December 2015
- Published by AIP Publishing in AIP Advances
- Vol. 5 (12) , 127240
Electrical characterization of fluorinated benzothiadiazole based conjugated copolymer – a promising material for high-performance solar cells
Measurements of electrical conductivity, electron work function, carrier mobility of holes and the diffusion length of excitons were performed on samples of conjugated polymers relevant to polymer solar cells. A state of the art fluorinated benzothiadiazole based conjugated copolymer (PBDTTHD − DTBTff) was studied and benchmarked against the reference polymer poly-3-hexylthiophene (P3HT). We employed, respectively, four electrode conductivity measurements, Kelvin probe work function measurements, carrier mobility using charge extraction by linearly increasing voltage (CELIV) measurements and diffusion length determinaton using surface photovoltage measurements.
- 1 December 2015
- Published by AIP Publishing in AIP Advances
- Vol. 5 (12) , 127240
Open AccessElectrical characterization of fluorinated benzothiadiazole based conjugated copolymer – a promising material for high-performance solar cells
Measurements of electrical conductivity, electron work function, carrier mobility of holes and the diffusion length of excitons were performed on samples of conjugated polymers relevant to polymer solar cells. A state of the art fluorinated benzothiadiazole based conjugated copolymer (PBDTTHD − DTBTff) was studied and benchmarked against the reference polymer poly-3-hexylthiophene (P3HT). We employed, respectively, four electrode conductivity measurements, Kelvin probe work function measurements, carrier mobility using charge extraction by linearly increasing voltage (CELIV) measurements and diffusion length determinaton using surface photovoltage measurements.
- 17 September 2015
- Published by Wiley in Advanced Engineering Materials
- Vol. 18 (4) , 511-517
Improving the Operational Stability of PBDTTTz‐4 Polymer Solar Cells Modules by Electrode Modification
PBDTTTz‐4 is employed in the ambient manufacturing of fully Roll‐to‐Roll organic solar cell modules. Modules are manufactured using a novel silver nanowire electrode or a previously reported carbon electrode. The average PCE of carbon modules (3.07%) and AgNW modules (1.46%) shows that PBDTTTz‐4 is a good candidate for upscaling. Stability measurements following the ISOS standards are used to compare the lifetime of the different modules. In all tests but one, the carbon modules are less stable. The higher stability of AgNW is attributed to the removal of the PEDOT:PSS in the front electrode. Finally during indoor light tests, a new degradation phenomenon is observed where bubbles are formed inside the modules contrary to previous reports of bubble formation by thermal expansion of trapped gas inside the barrier.
- 17 September 2015
- Published by Wiley in Advanced Engineering Materials
- Vol. 18 (4) , 511-517
Improving the Operational Stability of PBDTTTz‐4 Polymer Solar Cells Modules by Electrode Modification
PBDTTTz‐4 is employed in the ambient manufacturing of fully Roll‐to‐Roll organic solar cell modules. Modules are manufactured using a novel silver nanowire electrode or a previously reported carbon electrode. The average PCE of carbon modules (3.07%) and AgNW modules (1.46%) shows that PBDTTTz‐4 is a good candidate for upscaling. Stability measurements following the ISOS standards are used to compare the lifetime of the different modules. In all tests but one, the carbon modules are less stable. The higher stability of AgNW is attributed to the removal of the PEDOT:PSS in the front electrode. Finally during indoor light tests, a new degradation phenomenon is observed where bubbles are formed inside the modules contrary to previous reports of bubble formation by thermal expansion of trapped gas inside the barrier.
- 19 June 2015
- Published by Wiley in Advanced Energy Materials
- Vol. 5 (15) , 1500569
Upscaling of Perovskite Solar Cells: Fully Ambient Roll Processing of Flexible Perovskite Solar Cells with Printed Back Electrodes
A scaling effort on perovskite solar cells is presented where the device manufacture is progressed onto flexible substrates using scalable techniques such as slot‐die roll coating under ambient conditions. The printing of the back electrode using both carbon and silver is essential to the scaling effort. Both normal and inverted device geometries are explored and it is found that the formation of the correct morphology for the perovskite layer depends heavily on the surface upon which it is coated and this has significant implications for manufacture. The time it takes to form the desired layer morphology falls in the range of 5–45 min depending on the perovskite precursor, where the former timescale is compatible with mass production and the latter is best suited for laboratory work. A significant loss in solar cell performance of around 50% is found when progressing to using a fully scalable fabrication process, which is comparable to what is observed for other printable solar cell technologies such as polymer solar cells. The power conversion efficiency (PCE) for devices processed using spin coating on indium tin oxide (ITO)‐glass with evaporated back electrode yields a PCE of 9.4%. The same device type and active area realized using slot‐die coating on flexible ITO‐polyethyleneterphthalate (PET) with a printed back electrode gives a PCE of 4.9%.
- 19 June 2015
- Published by Wiley in Advanced Energy Materials
- Vol. 5 (15) , 1500569
Upscaling of Perovskite Solar Cells: Fully Ambient Roll Processing of Flexible Perovskite Solar Cells with Printed Back Electrodes
A scaling effort on perovskite solar cells is presented where the device manufacture is progressed onto flexible substrates using scalable techniques such as slot‐die roll coating under ambient conditions. The printing of the back electrode using both carbon and silver is essential to the scaling effort. Both normal and inverted device geometries are explored and it is found that the formation of the correct morphology for the perovskite layer depends heavily on the surface upon which it is coated and this has significant implications for manufacture. The time it takes to form the desired layer morphology falls in the range of 5–45 min depending on the perovskite precursor, where the former timescale is compatible with mass production and the latter is best suited for laboratory work. A significant loss in solar cell performance of around 50% is found when progressing to using a fully scalable fabrication process, which is comparable to what is observed for other printable solar cell technologies such as polymer solar cells. The power conversion efficiency (PCE) for devices processed using spin coating on indium tin oxide (ITO)‐glass with evaporated back electrode yields a PCE of 9.4%. The same device type and active area realized using slot‐die coating on flexible ITO‐polyethyleneterphthalate (PET) with a printed back electrode gives a PCE of 4.9%.
- 18 June 2015
- Published by Wiley in Advanced Functional Materials
- Vol. 25 (28) , 4539-4547
Roll‐to‐Roll Printed Silver Nanowire Semitransparent Electrodes for Fully Ambient Solution‐Processed Tandem Polymer Solar Cells
Silver nanowires (AgNWs) and zinc oxide (ZnO) are deposited on flexible substrates using fast roll‐to‐roll (R2R) processing. The AgNW film on polyethylene terephthalate (PET) shows >80% uniform optical transmission in the range of 550–900 nm. This electrode is compared to the previously reported and currently widely produced indium‐tin‐oxide (ITO) replacement comprising polyethylene terephthalate (PET)|silver grid|poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)|ZnO known as Flextrode. The AgNW/ZnO electrode shows higher transmission than Flextrode above 490 nm in the electromagnetic spectrum reaching up to 40% increased transmission at 750 nm in comparison to Flextrode. The functionality of AgNW electrodes is demonstrated in single and tandem polymer solar cells and compared with parallel devices on traditional Flextrode. All layers, apart from the semitransparent electrodes which are large‐scale R2R produced, are fabricated in ambient conditions on a laboratory roll‐coater using printing and coating methods which are directly transferrable to large‐scale R2R processing upon availability of materials. In a single cell structure, Flextrode is preferable with active layers based on poly‐3‐hexylthiophene(P3HT):phenyl‐C61‐butyric acid methylester (PCBM) and donor polymers of similar absorption characteristics while AgNW/ZnO electrodes are more compatible with low band gap polymer‐based single cells. In tandem devices, AgNW/ZnO is more preferable resulting in up to 80% improvement in PCE compared to parallel devices on Flextrode.
- 18 June 2015
- Published by Wiley in Advanced Functional Materials
- Vol. 25 (28) , 4539-4547
Roll‐to‐Roll Printed Silver Nanowire Semitransparent Electrodes for Fully Ambient Solution‐Processed Tandem Polymer Solar Cells
Silver nanowires (AgNWs) and zinc oxide (ZnO) are deposited on flexible substrates using fast roll‐to‐roll (R2R) processing. The AgNW film on polyethylene terephthalate (PET) shows >80% uniform optical transmission in the range of 550–900 nm. This electrode is compared to the previously reported and currently widely produced indium‐tin‐oxide (ITO) replacement comprising polyethylene terephthalate (PET)|silver grid|poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)|ZnO known as Flextrode. The AgNW/ZnO electrode shows higher transmission than Flextrode above 490 nm in the electromagnetic spectrum reaching up to 40% increased transmission at 750 nm in comparison to Flextrode. The functionality of AgNW electrodes is demonstrated in single and tandem polymer solar cells and compared with parallel devices on traditional Flextrode. All layers, apart from the semitransparent electrodes which are large‐scale R2R produced, are fabricated in ambient conditions on a laboratory roll‐coater using printing and coating methods which are directly transferrable to large‐scale R2R processing upon availability of materials. In a single cell structure, Flextrode is preferable with active layers based on poly‐3‐hexylthiophene(P3HT):phenyl‐C61‐butyric acid methylester (PCBM) and donor polymers of similar absorption characteristics while AgNW/ZnO electrodes are more compatible with low band gap polymer‐based single cells. In tandem devices, AgNW/ZnO is more preferable resulting in up to 80% improvement in PCE compared to parallel devices on Flextrode.
- 19 February 2015
- Published by Wiley in Advanced Energy Materials
- Vol. 5 (10) , 1402186
Matrix Organization and Merit Factor Evaluation as a Method to Address the Challenge of Finding a Polymer Material for Roll Coated Polymer Solar Cells
The results presented demonstrate how the screening of 104 light‐absorbing low band gap polymers for suitability in roll coated polymer solar cells can be accomplished through rational synthesis according to a matrix where 8 donor and 13 acceptor units are organized in rows and columns. Synthesis of all the polymers corresponding to all combinations of donor and acceptor units is followed by characterization of all the materials with respect to molecular weight, electrochemical energy levels, band gaps, photochemical stability, carrier mobility, and photovoltaic parameters. The photovoltaic evaluation is carried out with specific reference to scalable manufacture, which includes large area (1 cm2), stable inverted device architecture, an indium‐tin‐oxide‐free fully printed flexible front electrode with ZnO/PEDOT:PSS (poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate), and a printed silver comb back electrode structure. The matrix organization enables fast identification of active layer materials according to a weighted merit factor that includes more than simply the power conversion efficiency and is used as a method to identify the lead candidates. Based on several characteristics included in the merit factor, it is found that 13 out of the 104 synthesized polymers outperformed poly(3‐hexylthiophene) under the chosen processing conditions and thus can be suitable for further development.
- 19 February 2015
- Published by Wiley in Advanced Energy Materials
- Vol. 5 (10) , 1402186
Matrix Organization and Merit Factor Evaluation as a Method to Address the Challenge of Finding a Polymer Material for Roll Coated Polymer Solar Cells
The results presented demonstrate how the screening of 104 light‐absorbing low band gap polymers for suitability in roll coated polymer solar cells can be accomplished through rational synthesis according to a matrix where 8 donor and 13 acceptor units are organized in rows and columns. Synthesis of all the polymers corresponding to all combinations of donor and acceptor units is followed by characterization of all the materials with respect to molecular weight, electrochemical energy levels, band gaps, photochemical stability, carrier mobility, and photovoltaic parameters. The photovoltaic evaluation is carried out with specific reference to scalable manufacture, which includes large area (1 cm2), stable inverted device architecture, an indium‐tin‐oxide‐free fully printed flexible front electrode with ZnO/PEDOT:PSS (poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate), and a printed silver comb back electrode structure. The matrix organization enables fast identification of active layer materials according to a weighted merit factor that includes more than simply the power conversion efficiency and is used as a method to identify the lead candidates. Based on several characteristics included in the merit factor, it is found that 13 out of the 104 synthesized polymers outperformed poly(3‐hexylthiophene) under the chosen processing conditions and thus can be suitable for further development.