JGJosé Jaime García

José Jaime García

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


José Jaime García has a total of 59 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Reinforcement Strategies for 3D-Printed Structures: A Structural Behavior-Based Review

    by Lina Castro, Daniel Gomez, José J. García

    Structural reinforcement is essential for overcoming the limitations associated with layer-by-layer construction in 3D printing. However, existing studies typically evaluate reinforcement techniques as isolated solutions, limiting a unified understanding of how different reinforcement mechanisms contribute to structural performance. This review proposes a multiscale conceptual framework that classifies reinforcement strategies according to the structural scale at which they operate and the failure mechanisms they address. The literature on reinforcement approaches was systematically analyzed and organized into four structural scales: material, interface, element, and system. Furthermore, their influence on compressive, flexural, and shear behavior, along with anisotropy mitigation, was comparatively evaluated. The analysis shows that each reinforcement scale performs a distinct structural function. Material-scale reinforcement primarily controls cracking, while interface-scale reinforcement improves interlayer stress transfer and mitigates anisotropy. Element-scale reinforcement provides continuous load paths and increases load-bearing capacity, whereas system-scale reinforcement modifies global load distribution and structural response. These findings indicate that no single reinforcement scale addresses all the structural deficiencies associated with 3D-printed structures, highlighting the importance of interactions among complementary mechanisms across scales. The proposed framework relates reinforcement strategies to structural demands and governing failure mechanisms. The analysis identifies hybrid reinforcement systems, standardized evaluation procedures, multiscale modeling, and design methodologies as key directions for developing reinforced 3D-printed structures.

  • Open Access

    Buckling behavior of multi-slat bamboo structural members

    by Jhonathan Alexander Duque, Emmanuel Atienza, Luis Felipe López, José Jaime García

    Bamboo multi-slat members assembled from longitudinally cut slats offer improved geometric regularity and crack control compared with bamboo culms, enabling their use as load-bearing elements while reducing material waste. This study experimentally and analytically investigates the compressive behavior of bamboo multi-slat members intended for applications such as trusses, frames, and other structural systems. Two assembly approaches were evaluated: (i) planed Guadua angustifolia slats connected with tightened steel bolts, and (ii) naturally curved Dendrocalamus asper slats connected using non-tightened bolts or bamboo pins. The experimental program assessed buckling performance as a function of assembly approach, connector spacing, and connector type. The degree of structural interaction between slats was quantified using an index ratio, where values approaching unity indicate apparent flexural stiffness close to that of a fully interacting cross-section. All specimens failed by elastic buckling without significant material damage. Members assembled with planed slats and tightened bolts developed high index ratios (0.82–1.00), whereas members assembled with naturally curved slats exhibited substantially lower values (0.03–0.38). Increasing connector spacing from 100 to 300 mm reduced the buckling capacity of the first assembly approach by approximately 11%, while a more pronounced reduction was observed for the second approach. For the naturally curved assemblies, non-tightened steel bolts increased buckling capacity by a factor of 1.9–2.6 compared with bamboo pins. The European buckling formulation (EN 1995-1-1) provided reasonable predictions of the average experimental response of members assembled with planed slats when an imperfection factor of 0.39 was adopted but overestimated the capacity of the naturally curved assemblies. Finite element models reproduced the experimental trends and provided reasonable predictions of both buckling capacity and index ratio. The results demonstrate substantial differences in performance between the investigated assembly approaches and indicate that multi-slat bamboo members fabricated with planed slats and tightened bolts represent a promising alternative for compression-dominated structural applications, provided that adequate fabrication quality and connector detailing are maintained.

  • Open Access

    Experimental and theoretical characterization of bamboo’s transverse viscoelastic–plastic behavior

    by Carlos Patiño, Daniel Gomez, Jose J. Garcia

    Bamboo’s rapid growth, high axial mechanical strength comparable to that of low-carbon steels, and affordability make it a promising sustainable material for structural applications. However, its inherent heterogeneity, anisotropy, plasticity, and complex time-dependent response present significant challenges for modeling, design, and construction. Particularly, the viscoelastic–plastic behavior under sustained transverse compression remains poorly understood. This study presents a combined experimental–theoretical characterization of this behavior. Stress relaxation experiments were conducted on arc-shaped and hexahedral specimens subjected to 5–20% circumferential deformations. A new rheological model incorporating plastic effects via springs, dashpots, and a friction element was developed and showed strong agreement with experimental data ( $$R^{2}$$ R 2 =0.83–0.97). Plastic effects were evident across all strain levels, indicated by a 75–80% reduction in stiffness during loading. At 20% strain, pronounced damage was observed, including lateral material ejection, fiber extrusion, crushing, and internal cracking. Finite element models were used to verify the accuracy of simplified formulas for stress and strain. Digital image correlation analysis confirmed the generation of both plastic and viscoelastic deformation mechanisms. In arc-shaped specimens, the effective elastic modulus ranged from 149.5 to 195.2 MPa, while the yield stress varied from 4.9 to 6.2 MPa. Hexahedral specimens exhibited significant reductions in elastic modulus and yield stress, likely due to the removal of critical outer layers. This work demonstrates that accurate modeling of bamboo under transverse compression must account for both viscoelastic and plastic effects. Hence, this research provides a critical foundation for the design of metal-clamp connections and the optimization of densification processes.

  • Proposed Test Methods for Inclusion in ISO 22157

    by Kent A. Harries, Luisa Molari, José Jaime García

  • Open Access

    A Musculoskeletal Simulation Study to Evaluate the Influence of Postural and Anthropometric Variability on Intervertebral Loads During Manual Lifting in Construction

    by Jose Javier Guevara-Torres, Jhon Alexander Quiñones-Preciado, Alexander Paz, Héctor E. Jaramillo Suarez, José Jaime García, Lessby Gómez-Salazar

    Computational simulation is a valuable tool for advancing personalized ergonomics. This study evaluated the ability of musculoskeletal simulation to estimate individual lumbar loading during manual lifting tasks representative of construction activities. Fifty-six Colombian adults were recruited to reflect national anthropometric distributions and grouped by BMI and stature. Participants performed two standardized lifting tasks with a 10 kg load: symmetric lifting from the floor to xiphoid height and lateral lifting from a 0.40 m surface to shoulder height with contralateral transfer. Whole-body kinematics and ground reaction forces were processed in OpenSim software using the validated model to estimate L5–S1 compression and shear forces. Results showed a moderate association between lumbar compression and body weight, while shear forces exhibited low correlations with kinematic variables. Subject-specific scaled models revealed substantial inter-individual differences in lumbar loading related to lifting technique and anthropometric characteristics, highlighting the potential of musculoskeletal simulation for personalized risk assessment in construction.

  • Open Access

    Characterization of the uncertainty associated with viscoelastic creep model for Guadua angustifolia

    by Felipe Guerrero, Valeria Aguado, Jhonathan Duque, Albert R. Ortiz, José J. García, Daniel Gomez

  • Open Access

    3d printing applied to building development around the world: a systematic literature review

    by Sebastián Vélez Loaiza, Albert Ortiz, Daniel Gómez, Peter Thomson, Jose Jaime García, Eimar Sandoval

    The construction industry is undergoing a transformation towards automation, and 3D printing is at the forefront of this revolution. However, to optimise 3D printing in construction, it is crucial to consider the printer’s scale, the printing material’s rheological properties, and the printed structure’s mechanical properties. This paper provides an overview of the state of the art in this field, including the promising technologies, such as D-Shape and Contour Crafting, used in building applications. The paper also compares the use in 3D printing of conventional materials, like concrete, with non-conventional earth-based materials, such as sand, clay, and mud, or combinations with cementing materials. This review highlights the need for more research on alternative materials to concrete, particularly in developed countries. Nevertheless, earth-based materials offer significant potential for 3D printing in developing countries, where they are readily available. However, further research is necessary to improve the mechanical properties of 3D-printed elements, particularly for large-scale structures, to ensure their reliability and safety, making 3D printing a mainstream building method.


  • Open Access

    Expediting Finite Element Analyses for Subject-Specific Studies of Knee Osteoarthritis: A Literature Review

    by Alexander Paz, Gustavo A. Orozco, Rami K. Korhonen, José J. García, Mika E. Mononen

    Osteoarthritis (OA) is a degenerative disease that affects the synovial joints, especially the knee joint, diminishing the ability of patients to perform daily physical activities. Unfortunately, there is no cure for this nearly irreversible musculoskeletal disorder. Nowadays, many researchers aim for in silico-based methods to simulate personalized risks for the onset and progression of OA and evaluate the effects of different conservative preventative actions. Finite element analysis (FEA) has been considered a promising method to be developed for knee OA management. The FEA pipeline consists of three well-established phases: pre-processing, processing, and post-processing. Currently, these phases are time-consuming, making the FEA workflow cumbersome for the clinical environment. Hence, in this narrative review, we overviewed present-day trends towards clinical methods for subject-specific knee OA studies utilizing FEA. We reviewed studies focused on understanding mechanisms that initiate knee OA and expediting the FEA workflow applied to the whole-organ level. Based on the current trends we observed, we believe that forthcoming knee FEAs will provide nearly real-time predictions for the personalized risk of developing knee OA. These analyses will integrate subject-specific geometries, loading conditions, and estimations of local tissue mechanical properties. This will be achieved by combining state-of-the-art FEA workflows with automated approaches aided by machine learning techniques.