Mahmoud T. Abdu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mahmoud T. Abdu has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Maiada S. Abdelrahman
Metallurgical Engineering Department, Faculty of Engineering, Cairo University, Giza 12613, Egypt
9 shared publications - Waleed Khalifa
Department of Metallurgical Engineering, Faculty of Engineering, Cairo University, Giza, Egypt
4 shared publications Abdel-Hamid A. Hussein
2 shared publications- Emad A. Elshehy
Nuclear Materials Authority, El Maasi, Cairo, Egypt
2 shared publications - Mahmoud M. Tash
Cairo University
2 shared publications Saied E. Soliman
2 shared publications
Latest Publications
- 9 March 2026
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 356
Engineered microporous Fe–Zr silicate nanocomposite for simultaneous removal of As(III) and As(V)
- 9 March 2026
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 356
Engineered microporous Fe–Zr silicate nanocomposite for simultaneous removal of As(III) and As(V)
- 15 January 2026
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 12 (1) , 185-194
Mesoporous SiO 2 –Prussian blue composite for high-efficiency cesium ion removal
This research investigates the development of a mesoporous silica–Prussian blue (HOM-SiO 2 -PB) composite sorbent, synthesized using a one-pot in situ sol–gel lyotropic liquid crystal method.
- 15 January 2026
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 12 (1) , 185-194
Mesoporous SiO 2 –Prussian blue composite for high-efficiency cesium ion removal
This research investigates the development of a mesoporous silica–Prussian blue (HOM-SiO 2 -PB) composite sorbent, synthesized using a one-pot in situ sol–gel lyotropic liquid crystal method.
- Open Access
- 13 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (4) , 3712-3719
Harnessing mesoporosity and nitrogen doping to engineer a superior carbon-TiO 2 photocatalyst for methylene blue degradation
Nitrogen-doped carbon-modified TiO 2 (mNC-TiO 2 ) achieves 94.7% methylene blue degradation under visible light. Its stable mesostructure retains >90% efficiency over five cycles, offering a practical solution for wastewater treatment.
- 13 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (4) , 3712-3719
Open AccessHarnessing mesoporosity and nitrogen doping to engineer a superior carbon-TiO 2 photocatalyst for methylene blue degradation
Nitrogen-doped carbon-modified TiO 2 (mNC-TiO 2 ) achieves 94.7% methylene blue degradation under visible light. Its stable mesostructure retains >90% efficiency over five cycles, offering a practical solution for wastewater treatment.
- 1 July 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 180
Failure Analysis of Sulfur Solidification 2205 Duplex Stainless Steel Conveyor Belt
- 1 July 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 180
Failure Analysis of Sulfur Solidification 2205 Duplex Stainless Steel Conveyor Belt
- 21 May 2025
- Published by Wiley in Luminescence
- Vol. 40 (5) , e70196
Review of Photoluminescent–Photochromic Nanocomposites Containing Immobilized Inorganic Lanthanide‐Doped Strontium Aluminate Nanoparticles
Synthesizing photoluminescent–photochromic nanocomposites is a broad and active research area with many articles published in recent years. Literature lacks a systematic review of nanocomposites that combine both photoluminescence and photochromism at once. This review article focused on synthesizing, properties, and selected applications of photoluminescent–photochromic nanocomposites. These two characteristics were brought about together in the nanocomposites by the immobilization of inorganic lanthanide‐doped strontium aluminate nanoparticles (LSANs) in polymeric or ceramic matrices. The paper began by relating nanotechnology to composite materials and proceeded to discuss the concepts of luminescence and photochromism. Eventually, three main applications of such a class of nanocomposites were discussed in detail. The applications considered were smart windows, smart coatings, and anticounterfeiting. In all applications, the addition of the LSANs to the matrix material imparted magnificent enhancement of the photoluminescent and photochromic characteristics. Furthermore, the presence of LSANs in these nanocomposites caused remarkable enhancement in other properties such as mechanical properties, hydrophobicity, and protection against UV radiation.
- 21 May 2025
- Published by Wiley in Luminescence
- Vol. 40 (5) , e70196
Review of Photoluminescent–Photochromic Nanocomposites Containing Immobilized Inorganic Lanthanide‐Doped Strontium Aluminate Nanoparticles
Synthesizing photoluminescent–photochromic nanocomposites is a broad and active research area with many articles published in recent years. Literature lacks a systematic review of nanocomposites that combine both photoluminescence and photochromism at once. This review article focused on synthesizing, properties, and selected applications of photoluminescent–photochromic nanocomposites. These two characteristics were brought about together in the nanocomposites by the immobilization of inorganic lanthanide‐doped strontium aluminate nanoparticles (LSANs) in polymeric or ceramic matrices. The paper began by relating nanotechnology to composite materials and proceeded to discuss the concepts of luminescence and photochromism. Eventually, three main applications of such a class of nanocomposites were discussed in detail. The applications considered were smart windows, smart coatings, and anticounterfeiting. In all applications, the addition of the LSANs to the matrix material imparted magnificent enhancement of the photoluminescent and photochromic characteristics. Furthermore, the presence of LSANs in these nanocomposites caused remarkable enhancement in other properties such as mechanical properties, hydrophobicity, and protection against UV radiation.
- 11 July 2024
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 99 (9) , 1941-1954
Fast in‐situ synthesis of mesoporous Prussian blue‐silica nanocomposite for superior silver ions recovery performance
BACKGROUND: Mesoporous‐nanostructured silica‐Prussian blue composite is a highly potential material for silver ions removal and recovery from wastewater. Intense interest has been shown in the use of Prussian blue (PB), one of the important coordinated materials and its analogues in removal of toxic and valuable ions.METHODS: The micro‐emulsion template method enables the synthesis of Prussian blue (PB) within silica pores, yielding a nanostructured mesoporous silica‐PB composite. This rapid synthesis technique allows for the direct fabrication of the composite from mixed precursor solutions within minutes. The resulting material is effective for selectively extracting silver ions from wastewater at a specific pH level.RESULTS AND DISCUSSION: In summary, the synthesized SiO2‐Prussian blue composite was extensively analyzed using various techniques including XPS, HR‐TEM, SEM, STEM‐EDX elemental maps, TGA/TDA, and N2 adsorption/desorption measurements. The composite exhibited a BET surface area of 203 m2 g−1 and a total pore volume of approximately 0.283 cm3 g−1with mesopores centered around 20 nm. This mesoporous SiO2‐Prussian blue demonstrated significant effectiveness in removing silver ions, with a maximum adsorption capacity of 107.5 mg g−1. The Langmuir and Sips isotherms showed the best fit among various adsorption isotherm types, with R2 values exceeding 0.984. Additionally, kinetic analyses revealed that the pseudo‐second‐order model accurately described the adsorption of silver ions onto the synthesized adsorbent. The nano‐particles exhibit remarkable long‐term stability, maintaining good reproducibility even after five regeneration cycles. © 2024 Society of Chemical Industry (SCI).
- 11 July 2024
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 99 (9) , 1941-1954
Fast in‐situ synthesis of mesoporous Prussian blue‐silica nanocomposite for superior silver ions recovery performance
BACKGROUND: Mesoporous‐nanostructured silica‐Prussian blue composite is a highly potential material for silver ions removal and recovery from wastewater. Intense interest has been shown in the use of Prussian blue (PB), one of the important coordinated materials and its analogues in removal of toxic and valuable ions.METHODS: The micro‐emulsion template method enables the synthesis of Prussian blue (PB) within silica pores, yielding a nanostructured mesoporous silica‐PB composite. This rapid synthesis technique allows for the direct fabrication of the composite from mixed precursor solutions within minutes. The resulting material is effective for selectively extracting silver ions from wastewater at a specific pH level.RESULTS AND DISCUSSION: In summary, the synthesized SiO2‐Prussian blue composite was extensively analyzed using various techniques including XPS, HR‐TEM, SEM, STEM‐EDX elemental maps, TGA/TDA, and N2 adsorption/desorption measurements. The composite exhibited a BET surface area of 203 m2 g−1 and a total pore volume of approximately 0.283 cm3 g−1with mesopores centered around 20 nm. This mesoporous SiO2‐Prussian blue demonstrated significant effectiveness in removing silver ions, with a maximum adsorption capacity of 107.5 mg g−1. The Langmuir and Sips isotherms showed the best fit among various adsorption isotherm types, with R2 values exceeding 0.984. Additionally, kinetic analyses revealed that the pseudo‐second‐order model accurately described the adsorption of silver ions onto the synthesized adsorbent. The nano‐particles exhibit remarkable long‐term stability, maintaining good reproducibility even after five regeneration cycles. © 2024 Society of Chemical Industry (SCI).
- 4 January 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (7) , 11518-11527
Electrospinning of glass nanofibers to roughen a waterborne polyurethane coating toward smart applications
- 4 January 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (7) , 11518-11527
Electrospinning of glass nanofibers to roughen a waterborne polyurethane coating toward smart applications
- Open Access
- 22 November 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-15
Investigation of erosion-corrosion failure of API X52 carbon steel pipeline
A failure analysis of API X52 steel pipeline was conducted. The investigation included complete material characterizations using tensile and hardness testing, optical microscope, SEM, and EDS. The main failure occurred in the downstream pipe located near the welded joint at the elbow outlet instead of elbow which was interesting. The main mechanism of failure was found to be erosion-corrosion mechanism that caused breakdown of the protective FeCO3 film, thinning of the downstream pipe, and finally failure. It is believed that the erosion-corrosion was induced by sand impingement due to turbulent flow that was promoted by sudden change in the flow cross section between the elbow inlet and upstream pipe and poor welding quality of joint at the elbow outlet.
- 22 November 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-15
Open AccessInvestigation of erosion-corrosion failure of API X52 carbon steel pipeline
A failure analysis of API X52 steel pipeline was conducted. The investigation included complete material characterizations using tensile and hardness testing, optical microscope, SEM, and EDS. The main failure occurred in the downstream pipe located near the welded joint at the elbow outlet instead of elbow which was interesting. The main mechanism of failure was found to be erosion-corrosion mechanism that caused breakdown of the protective FeCO3 film, thinning of the downstream pipe, and finally failure. It is believed that the erosion-corrosion was induced by sand impingement due to turbulent flow that was promoted by sudden change in the flow cross section between the elbow inlet and upstream pipe and poor welding quality of joint at the elbow outlet.