Emilio Ernesto Paladino
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Emilio Ernesto Paladino has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Rafael Franklin Lazaro de Cerqueira
Center for Petroleum Studies -University of Campinas, UNICAMP Rua Cora Coralina, 350, Cidade Universitária, Campinas-SP, Brazil
5 shared publications - Josiane Weise3 shared publications
- João Alves de Lima
Renewable and Alternative Energy Center (CEAR), Federal University of Paraiba (UFPB), Cidade Universitária, João Pessoa 58051-970, Paraíba, Brazil
3 shared publications Rairam F.C. Almeida
MSX/Ford South America - Brazil
3 shared publicationsClovis R. Maliska
Computational Fluid Dynamics Lab - SINMEC, Federal University of Santa Catarina, SC, Brazil
2 shared publications- Fabien Evrard
Chair of Mechanical Process Engineering, Otto-von-Guericke-Universität Magdeburg, Universitätsplatz 2, 39106 Magdeburg, Germany
2 shared publications
Latest Publications
- Open Access
- 23 April 2026
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 201
DNS study of near interface turbulence in co-current stratified gas–liquid flow using a VOF approach for different liquid film heights
- 23 April 2026
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 201
Open AccessDNS study of near interface turbulence in co-current stratified gas–liquid flow using a VOF approach for different liquid film heights
- 10 March 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 328
Thermodynamic investigation of CO2 – CH4 mixtures in water and brine for subsea natural gas separation applications
- 10 March 2026
- Published by Elsevier in Chemical Engineering Science
- Vol. 328
Thermodynamic investigation of CO2 – CH4 mixtures in water and brine for subsea natural gas separation applications
- 2 July 2025
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 192
Enhanced modeling for resolved morphologies in co-current stratified wavy pipe flows
- 2 July 2025
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 192
Enhanced modeling for resolved morphologies in co-current stratified wavy pipe flows
- 1 December 2021
- Published by Elsevier in Flow Measurement and Instrumentation
- Vol. 82
CFD study of the transient wet gas flow behavior through orifice plate flow meters
- 1 December 2021
- Published by Elsevier in Flow Measurement and Instrumentation
- Vol. 82
CFD study of the transient wet gas flow behavior through orifice plate flow meters
- 28 October 2021
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 43 (11) , 1-15
Performance evaluation of standard second-order finite volume method for DNS solution of turbulent channel flow
- 28 October 2021
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 43 (11) , 1-15
Performance evaluation of standard second-order finite volume method for DNS solution of turbulent channel flow
- Open Access
- 1 September 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1180 (1) , 012017
Numerical-experimental investigation of liquid slugging in the suction muffler of a hermetic reciprocating compressor
Refrigerant in the liquid phase and lubricating oil that circulate in refrigeration systems may reach the compression chamber of compressors. This phenomenon of liquid slugging is detrimental to reciprocating compressors because it can damage valves and other components. A three-dimensional Eulerian multiphase model was developed using the software ANSYS CFX to predict the gas-liquid flow in a simplified suction muffler geometry. In addition, an experimental bench was designed to allow the injection of specified volumes of lubricant oil into the suction muffler and measurement of the volume that reaches the muffler outlet. The liquid slugging was observed through glass windows positioned in the test section and recorded with a high-speed camera. Measurements showed that the phenomenon of liquid slugging is random and that the volume of liquid reaching the muffler outlet increases with the oil injection pressure. The numerical model was able to predict the oil volume that reaches the muffler outlet in agreement with measurements in the case of high injection pressures, but it overpredicted the volume when the injection pressure was decreased. The visualization showed changes in the liquid phase morphology that are difficult to predict since closure models for a two-fluid model are typically developed for dispersed morphology.
- 1 September 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1180 (1) , 012017
Open AccessNumerical-experimental investigation of liquid slugging in the suction muffler of a hermetic reciprocating compressor
Refrigerant in the liquid phase and lubricating oil that circulate in refrigeration systems may reach the compression chamber of compressors. This phenomenon of liquid slugging is detrimental to reciprocating compressors because it can damage valves and other components. A three-dimensional Eulerian multiphase model was developed using the software ANSYS CFX to predict the gas-liquid flow in a simplified suction muffler geometry. In addition, an experimental bench was designed to allow the injection of specified volumes of lubricant oil into the suction muffler and measurement of the volume that reaches the muffler outlet. The liquid slugging was observed through glass windows positioned in the test section and recorded with a high-speed camera. Measurements showed that the phenomenon of liquid slugging is random and that the volume of liquid reaching the muffler outlet increases with the oil injection pressure. The numerical model was able to predict the oil volume that reaches the muffler outlet in agreement with measurements in the case of high injection pressures, but it overpredicted the volume when the injection pressure was decreased. The visualization showed changes in the liquid phase morphology that are difficult to predict since closure models for a two-fluid model are typically developed for dispersed morphology.