Solaiappan Ananthakumar
Research Subjects
Solaiappan Ananthakumar has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Kallyadan Veettil Mahesh
National Institute for Interdisciplinary Science and Technology (CSIR)
8 shared publications A. Peer Mohamed
Materials Science and Technology Division
6 shared publicationsAbdul Azeez Peer Mohamed
Functional Materials Section Materials Science and Technology Division (MSTD) CSIR-National Institute for Interdisciplinary Science and Technology (CSIR-NIIST) Thiruvananthapuram, Kerala 695 019 India
5 shared publications- Balanand Santhosh
Department of Energy Conversion and Storage, Faculty of Chemistry, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
3 shared publications - R. V. Mangalaraja
Department of Materials Engineering, University of Concepcion, Concepcion, Chile
3 shared publications - Renaud Metz
Laboratoire Charles Coulomb UMR 5221 CNRS-Université de Montpellier (Université Claude Bernard - Lyon 1), Montpellier, France
3 shared publications
Latest Publications
- 11 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 3 (6) , 1905-1914
CO2 Adsorption Studies of Hydrophobic Silica Sorbent Functionalized with Silicone Oil-Amine Blends under Low-Temperature Conditions
CO2 uptake using multifunctional, porous solid sorbents has gained significant attention due to their high thermochemical stability and selectivity. In this study, hydrophilic nanosilica was functionalized with blends of silicone oil and amines to develop hydrophobic silica sorbents capable of adsorbing CO2 at low temperatures in the presence of moisture. The adsorption performance of these sorbents was evaluated at 35 and 40 °C using silicone oil blends containing monoethanolamine (MEA), diethanolamine (DEA), and triethanolamine (TEA). Among these, the sorbent prepared with MEA, a primary amine, demonstrated the highest CO2 adsorption capacity. Further enhancement was achieved by functionalizing silicone oil with aminopropyltrimethoxysilane (APTMS). The optimized silica sorbent, with a 1:1 APTMS-to-silicone oil ratio, exhibited a maximum adsorption capacity of 0.75 and 0.86 mmol/g at 35 and 40 °C, respectively, and a water contact angle of 134°, achieving an optimal balance between hydrophobicity and amine reactivity. Their enhanced adsorption capacity and structural resilience suggest applications where intermittent moisture exposure may occur, such as indoor air purification systems, industrial enclosures, and controlled environments like greenhouses or cabin spaces. The hydrophobic surface is expected to improve durability and minimize water interference in such applications.
- 11 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Engineering Materials
- Vol. 3 (6) , 1905-1914
CO2 Adsorption Studies of Hydrophobic Silica Sorbent Functionalized with Silicone Oil-Amine Blends under Low-Temperature Conditions
CO2 uptake using multifunctional, porous solid sorbents has gained significant attention due to their high thermochemical stability and selectivity. In this study, hydrophilic nanosilica was functionalized with blends of silicone oil and amines to develop hydrophobic silica sorbents capable of adsorbing CO2 at low temperatures in the presence of moisture. The adsorption performance of these sorbents was evaluated at 35 and 40 °C using silicone oil blends containing monoethanolamine (MEA), diethanolamine (DEA), and triethanolamine (TEA). Among these, the sorbent prepared with MEA, a primary amine, demonstrated the highest CO2 adsorption capacity. Further enhancement was achieved by functionalizing silicone oil with aminopropyltrimethoxysilane (APTMS). The optimized silica sorbent, with a 1:1 APTMS-to-silicone oil ratio, exhibited a maximum adsorption capacity of 0.75 and 0.86 mmol/g at 35 and 40 °C, respectively, and a water contact angle of 134°, achieving an optimal balance between hydrophobicity and amine reactivity. Their enhanced adsorption capacity and structural resilience suggest applications where intermittent moisture exposure may occur, such as indoor air purification systems, industrial enclosures, and controlled environments like greenhouses or cabin spaces. The hydrophobic surface is expected to improve durability and minimize water interference in such applications.
- 21 January 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (4) , 2531-2539
Silicone Oil-Functionalized Hydrophobic Nano Silica: A Floating Sorbent for Organic Pollutant Removal in Aquatic Systems
Meso/microporous nano silica modified with macromolecular polymers produces attractive hybrids that repel water and have a hydrophobic surface, making them highly effective for targeting and eliminating organic contaminants in aquatic environments. In this study, nano silica was functionalized with silicone oil, an oligomeric siloxane derivative, to produce a hydrophobic silica nano hybrid characterized by a non-wetting water contact angle of 139°. This hydrophobic hybrid nano silica showed a sustainable floating nature on water even in turbulent streams. Due to such robust hydrophobic properties, the hybrid was explored for the separation of three different kinds of contaminants, such as (i) organic dyes, (ii) antibiotics, and (iii) nicotine. The concept of a floating sorbent has been innovatively introduced in this study through the application of silicone oil-modified nano silica. The adsorption experiments were systematically planned, and the data related to the percentage adsorption of contaminants with respect to dosage, pH, and concentration are reported. The results indicated an adsorption efficiency of >99% for cationic dyes with moderate adsorption observed for nicotine and antibiotics. The study highlights the significant potential of silicone oil-modified silica as a hydrophobic floating sorbent for environmental remediation. Buoyancy and strong water-repellent properties facilitate easy recovery and reuse, offering a sustainable and efficient method for the removal of diverse organic pollutants from water systems.
- 21 January 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (4) , 2531-2539
Silicone Oil-Functionalized Hydrophobic Nano Silica: A Floating Sorbent for Organic Pollutant Removal in Aquatic Systems
Meso/microporous nano silica modified with macromolecular polymers produces attractive hybrids that repel water and have a hydrophobic surface, making them highly effective for targeting and eliminating organic contaminants in aquatic environments. In this study, nano silica was functionalized with silicone oil, an oligomeric siloxane derivative, to produce a hydrophobic silica nano hybrid characterized by a non-wetting water contact angle of 139°. This hydrophobic hybrid nano silica showed a sustainable floating nature on water even in turbulent streams. Due to such robust hydrophobic properties, the hybrid was explored for the separation of three different kinds of contaminants, such as (i) organic dyes, (ii) antibiotics, and (iii) nicotine. The concept of a floating sorbent has been innovatively introduced in this study through the application of silicone oil-modified nano silica. The adsorption experiments were systematically planned, and the data related to the percentage adsorption of contaminants with respect to dosage, pH, and concentration are reported. The results indicated an adsorption efficiency of >99% for cationic dyes with moderate adsorption observed for nicotine and antibiotics. The study highlights the significant potential of silicone oil-modified silica as a hydrophobic floating sorbent for environmental remediation. Buoyancy and strong water-repellent properties facilitate easy recovery and reuse, offering a sustainable and efficient method for the removal of diverse organic pollutants from water systems.
- 26 July 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (8) , 12115-12127
Decolorization of cashew nut shell liquid (CNSL) using kaolin clay: a facile refinement strategy for a sustainable bio-based resource
- 26 July 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (8) , 12115-12127
Decolorization of cashew nut shell liquid (CNSL) using kaolin clay: a facile refinement strategy for a sustainable bio-based resource
- Open Access
- 27 January 2023
- Published by Wiley in Medcomm – Biomaterials and Applications
- Vol. 2 (1)
2‐Hydroxy‐1,4‐naphthoquinone [Lawsone] integrated rare‐earth hybrid materials as biocompatible UV/IR filter agents
UV filter agents are essential ingredients in cosmetics and fabrics for rendering the property of protection from harmful UV radiation. The focus of this research was on the development of biocompatible hybrid UV/IR filter agents through sol–gel processing of nano‐sized lanthanum titanate, zirconate, and phosphate‐based rare‐earth materials. 2‐Hydroxy‐1,4‐naphthoquinone (Lawsone) is an ideal candidate, owing to its biocompatibility, for treating the sol of the rare‐earth systems to produce inorganic‐organic hybrids with classical orange shades. The rare‐earth hybrids were characterized by X‐Ray diffraction, dynamic light scattering, fourier transform infrared spectroscopy, scanning electron microscopy, UV‐Vis, photo‐luminescence, and Near Infrared (NIR) spectroscopy. The results of characterization indicated that the hybrids offer >90% of NIR reflectance in the wavelength region from 700 to 1100 nm. They also exhibited excellent shielding in UV‐A and UV‐B regions, thus qualifying them as cool colors with useful optical as well as heat management characteristics. The sun protection factor calculated by optical density measurements showed that the synthesized hybrids have potential applications as UV filter agents in sunscreen lotions. The cell viability analyzed by the MTT (4,5‐dimethylthiazol‐2‐yl)−2,5‐diphenyltetrazolium bromide) assay affirmed the biocompatibility of the hybrids as none of the systems was found cytotoxic. This study was devoted to exploring the beneficial properties of rare‐earth‐based hybrid systems in pharmacological applications.
- 27 January 2023
- Published by Wiley in Medcomm – Biomaterials and Applications
- Vol. 2 (1)
Open Access2‐Hydroxy‐1,4‐naphthoquinone [Lawsone] integrated rare‐earth hybrid materials as biocompatible UV/IR filter agents
UV filter agents are essential ingredients in cosmetics and fabrics for rendering the property of protection from harmful UV radiation. The focus of this research was on the development of biocompatible hybrid UV/IR filter agents through sol–gel processing of nano‐sized lanthanum titanate, zirconate, and phosphate‐based rare‐earth materials. 2‐Hydroxy‐1,4‐naphthoquinone (Lawsone) is an ideal candidate, owing to its biocompatibility, for treating the sol of the rare‐earth systems to produce inorganic‐organic hybrids with classical orange shades. The rare‐earth hybrids were characterized by X‐Ray diffraction, dynamic light scattering, fourier transform infrared spectroscopy, scanning electron microscopy, UV‐Vis, photo‐luminescence, and Near Infrared (NIR) spectroscopy. The results of characterization indicated that the hybrids offer >90% of NIR reflectance in the wavelength region from 700 to 1100 nm. They also exhibited excellent shielding in UV‐A and UV‐B regions, thus qualifying them as cool colors with useful optical as well as heat management characteristics. The sun protection factor calculated by optical density measurements showed that the synthesized hybrids have potential applications as UV filter agents in sunscreen lotions. The cell viability analyzed by the MTT (4,5‐dimethylthiazol‐2‐yl)−2,5‐diphenyltetrazolium bromide) assay affirmed the biocompatibility of the hybrids as none of the systems was found cytotoxic. This study was devoted to exploring the beneficial properties of rare‐earth‐based hybrid systems in pharmacological applications.
- 23 February 2021
- Published by Wiley in Chemistry – An Asian Journal
- Vol. 16 (7) , 822-836
IR Reflective LaPO4 Ceramic Colorant Reinforced Polymer Composite Coatings on Glass and Metal Substrates for Heat Management Applications
LaPO4 ceramic colorants were processed in the vibrant shades of green and brick red, and subsequently embedded in polymer resins for the fabrication of heat management coatings. The IR/UV shielding characteristics of these ceramic colorants and polymer coatings were analysed and it was found that the ceramic dispersoids enhance the IR reflectance quality of polymer resins by 20 to 25 times. The nano ceramic green colorant‐reinforced polymer coating on glass panels offers the stringent property, i. e., optical transparency and heat reflectance combined, when exposed to direct sunlight. Other photophysical properties were also studied and analysed. The brick red colorant entrenched resin coating on metal substrate offered heat reflectance and corrosion resistance characteristics. XPS studies provided the chemical environment of the systems. Surface morphology, crystallinity and particle size of the products were investigated using SEM, TEM, XRD and DLS techniques. The polymer resin coating of these ceramic colorants offers thermal stability and colorfastness properties.
- 23 February 2021
- Published by Wiley in Chemistry – An Asian Journal
- Vol. 16 (7) , 822-836
IR Reflective LaPO4 Ceramic Colorant Reinforced Polymer Composite Coatings on Glass and Metal Substrates for Heat Management Applications
LaPO4 ceramic colorants were processed in the vibrant shades of green and brick red, and subsequently embedded in polymer resins for the fabrication of heat management coatings. The IR/UV shielding characteristics of these ceramic colorants and polymer coatings were analysed and it was found that the ceramic dispersoids enhance the IR reflectance quality of polymer resins by 20 to 25 times. The nano ceramic green colorant‐reinforced polymer coating on glass panels offers the stringent property, i. e., optical transparency and heat reflectance combined, when exposed to direct sunlight. Other photophysical properties were also studied and analysed. The brick red colorant entrenched resin coating on metal substrate offered heat reflectance and corrosion resistance characteristics. XPS studies provided the chemical environment of the systems. Surface morphology, crystallinity and particle size of the products were investigated using SEM, TEM, XRD and DLS techniques. The polymer resin coating of these ceramic colorants offers thermal stability and colorfastness properties.
- Open Access
- 18 December 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (73) , 44773
Correction: Photoactive, antimicrobial CeO2 decorated AlOOH/PEI hybrid nanocomposite: a multifunctional catalytic-sorbent for lignin and organic dye
Correction for ‘Photoactive, antimicrobial CeO2 decorated AlOOH/PEI hybrid nanocomposite: a multifunctional catalytic-sorbent for lignin and organic dye’ by K. Aboo Shuhailath et al., RSC Adv., 2016, 6, 54357–54370, DOI: 10.1039/C6RA07836B.
- 18 December 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (73) , 44773
Open AccessCorrection: Photoactive, antimicrobial CeO2 decorated AlOOH/PEI hybrid nanocomposite: a multifunctional catalytic-sorbent for lignin and organic dye
Correction for ‘Photoactive, antimicrobial CeO2 decorated AlOOH/PEI hybrid nanocomposite: a multifunctional catalytic-sorbent for lignin and organic dye’ by K. Aboo Shuhailath et al., RSC Adv., 2016, 6, 54357–54370, DOI: 10.1039/C6RA07836B.
- Open Access
- 14 October 2019
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 4 (19) , 17990-18001
Superswelling Hybrid Sponge from Water Glass for Selective Absorption of Crude Oil and Organic Solvents
A lightweight super hydrophilic hybrid sponge is designed and demonstrated out of water glass and an organic polymer, which has a macroporous flaky nature and is superflexible with an apparent density of 0.069 g cc–1, ∼97% porosity, and 3000% water uptake. The octadecyltrimethoxy silane-modified hybrid sponge exhibits selective absorption of oil and organic solvents in open water. An absorption capacity in the range 12–23 g g–1 for the test liquids light crude oil, engine oil, paraffin oil, chloroform, kerosene, and hexane is revealed. Absorption capacity by a weight basis was directly proportional to the density and inversely proportional to the viscosity of test liquids. Trials under both stagnant and turbulent conditions verify selective uptake of oil from sea water. Complete regeneration of the absorbent was possible for ten cycles for the test liquids. The work provides design of an affordable water clean-up material alternative to commonly used polyurethane sponges.
- 14 October 2019
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 4 (19) , 17990-18001
Open AccessSuperswelling Hybrid Sponge from Water Glass for Selective Absorption of Crude Oil and Organic Solvents
A lightweight super hydrophilic hybrid sponge is designed and demonstrated out of water glass and an organic polymer, which has a macroporous flaky nature and is superflexible with an apparent density of 0.069 g cc–1, ∼97% porosity, and 3000% water uptake. The octadecyltrimethoxy silane-modified hybrid sponge exhibits selective absorption of oil and organic solvents in open water. An absorption capacity in the range 12–23 g g–1 for the test liquids light crude oil, engine oil, paraffin oil, chloroform, kerosene, and hexane is revealed. Absorption capacity by a weight basis was directly proportional to the density and inversely proportional to the viscosity of test liquids. Trials under both stagnant and turbulent conditions verify selective uptake of oil from sea water. Complete regeneration of the absorbent was possible for ten cycles for the test liquids. The work provides design of an affordable water clean-up material alternative to commonly used polyurethane sponges.
- 10 July 2019
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 35 (29) , 9382-9395
Double-Silicate Derived Hybrid Foams for High-Capacity Adsorption of Textile Dye Effluent: Statistical Optimization and Adsorption Studies
In this work, a lightweight inorganic–organic hybrid foam adsorbent is processed out of economically cheap “double-silicate” precursors employing natural bentonite and water glass through a facile cross-linking and polymerization technique. Poly(vinyl alcohol) was used to provide structural strength to the three-dimensional framework. The foam adsorbent possessed an apparent density of 0.083 g cm–3, indicating its internetworks and exposed surface area for the uptake of dyes. The foam was systematically studied for the treatment of textile dye effluent. Multivariate optimization process was carried out using response surface methodology. The Box–Behnken model was used for the design of experiments and to study the interplay between the variables. Batch adsorption and continuous column adsorption studies were carried out at respective levels of initial concentration (200–1000 μM), adsorbent dose (1–10 g L–1), and contact time (0–120 min). The results revealed that the hybrid silicate foam exhibits adsorption capacity as high as 99.9, 98.9, and 98.2% for 200, 600, and 1000 μM concentrations of methylene blue in 120 min, respectively, and 100% adsorption for 200, 600, and 1000 μM concentrations of crystal violet in 120 min for 10 g L–1 of adsorbent. Adsorption equilibrium data fitted well to Langmuir isotherm, and the kinetics followed second-order kinetic model. Synthetic industrial effluent with 1000 μM dye concentration was also prepared and studied with continuous column for determining the working capacity of the adsorbent, and the results are presented. The silicate hybrid foam is a cheap adsorbent that does not produce any secondary waste and can be repeatedly used making it attractive for dye industries.
- 10 July 2019
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 35 (29) , 9382-9395
Double-Silicate Derived Hybrid Foams for High-Capacity Adsorption of Textile Dye Effluent: Statistical Optimization and Adsorption Studies
In this work, a lightweight inorganic–organic hybrid foam adsorbent is processed out of economically cheap “double-silicate” precursors employing natural bentonite and water glass through a facile cross-linking and polymerization technique. Poly(vinyl alcohol) was used to provide structural strength to the three-dimensional framework. The foam adsorbent possessed an apparent density of 0.083 g cm–3, indicating its internetworks and exposed surface area for the uptake of dyes. The foam was systematically studied for the treatment of textile dye effluent. Multivariate optimization process was carried out using response surface methodology. The Box–Behnken model was used for the design of experiments and to study the interplay between the variables. Batch adsorption and continuous column adsorption studies were carried out at respective levels of initial concentration (200–1000 μM), adsorbent dose (1–10 g L–1), and contact time (0–120 min). The results revealed that the hybrid silicate foam exhibits adsorption capacity as high as 99.9, 98.9, and 98.2% for 200, 600, and 1000 μM concentrations of methylene blue in 120 min, respectively, and 100% adsorption for 200, 600, and 1000 μM concentrations of crystal violet in 120 min for 10 g L–1 of adsorbent. Adsorption equilibrium data fitted well to Langmuir isotherm, and the kinetics followed second-order kinetic model. Synthetic industrial effluent with 1000 μM dye concentration was also prepared and studied with continuous column for determining the working capacity of the adsorbent, and the results are presented. The silicate hybrid foam is a cheap adsorbent that does not produce any secondary waste and can be repeatedly used making it attractive for dye industries.
- 1 April 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 9, 32-37
Optically Transparent Polymer Coating Embedded with IR Reflective Rare Earth Yellow Pigment: - Innovative Strategy for Cool Windows
- 1 April 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 9, 32-37
Optically Transparent Polymer Coating Embedded with IR Reflective Rare Earth Yellow Pigment: - Innovative Strategy for Cool Windows
- Open Access
- 19 March 2019
- Published by Springer Nature in Sustainable Environment Research
- Vol. 29 (1) , 1
Competitive photo-degradation performance of ZnO modified bentonite clay in water containing both organic and inorganic contaminants
- 19 March 2019
- Published by Springer Nature in Sustainable Environment Research
- Vol. 29 (1) , 1
Open AccessCompetitive photo-degradation performance of ZnO modified bentonite clay in water containing both organic and inorganic contaminants