Yasin Amani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yasin Amani has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Eric Maire
INSA Lyon 20 Avenue Albert Einstein
4 shared publications - Sylvain Dancette
INSA Lyon, CNRS, MATEIS, UMR5510, Villeurbanne, France
3 shared publications Jérôme Adrien
2 shared publicationsNingzhen Wang
2 shared publicationsXiang Chen
2 shared publicationsYanxiang Li
2 shared publications
Latest Publications
- 1 January 2019
- Published by Elsevier in Materials Characterization
- Vol. 147, 11-20
Compressive performance and deformation mechanism of the dynamic gas injection aluminum foams
- 1 January 2019
- Published by Elsevier in Materials Characterization
- Vol. 147, 11-20
Compressive performance and deformation mechanism of the dynamic gas injection aluminum foams
- Open Access
Two-Scale Tomography Based Finite Element Modeling of Plasticity and Damage in Aluminum Foams
In this study, finite element (FE) modeling of open-cell aluminum foams in tension was performed based on laboratory X-ray tomography scans of the materials at two different scales. High-resolution stitching tomography of the initial state allowed local intermetallic particles to be distinguished from internal defects in the solid phase of the foam. Lower-resolution scans were used to monitor the deformation and fracture in situ during loading. 3D image-based FE models of the foams were built to simulate the tensile behavior using a new microstructure-informed Gurson–Tvergaard–Needleman model. The new model allows quantitative consideration of the local presence of brittle intermetallic particles in the prediction of damage. It performs well in the discrimination of potential fracture zones in the foam, and can be easily adapted to any type of architectured material where both the global architecture and local microstructural details should be taken into account in the prediction of damage behavior.
Open AccessTwo-Scale Tomography Based Finite Element Modeling of Plasticity and Damage in Aluminum Foams
In this study, finite element (FE) modeling of open-cell aluminum foams in tension was performed based on laboratory X-ray tomography scans of the materials at two different scales. High-resolution stitching tomography of the initial state allowed local intermetallic particles to be distinguished from internal defects in the solid phase of the foam. Lower-resolution scans were used to monitor the deformation and fracture in situ during loading. 3D image-based FE models of the foams were built to simulate the tensile behavior using a new microstructure-informed Gurson–Tvergaard–Needleman model. The new model allows quantitative consideration of the local presence of brittle intermetallic particles in the prediction of damage. It performs well in the discrimination of potential fracture zones in the foam, and can be easily adapted to any type of architectured material where both the global architecture and local microstructural details should be taken into account in the prediction of damage behavior.
- Top Cited Papers
- 1 October 2018
- Published by Elsevier in Acta Materialia
- Vol. 159, 395-407
Compression behavior of lattice structures produced by selective laser melting: X-ray tomography based experimental and finite element approaches
- 1 October 2018
- Published by Elsevier in Acta Materialia
- Vol. 159, 395-407
Top Cited PapersCompression behavior of lattice structures produced by selective laser melting: X-ray tomography based experimental and finite element approaches
- 1 July 2018
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 122, 1-10
Thermal conductivity of highly porous metal foams: Experimental and image based finite element analysis
- 1 July 2018
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 122, 1-10
Thermal conductivity of highly porous metal foams: Experimental and image based finite element analysis
- 1 April 2018
- Published by Elsevier in Materials Characterization
- Vol. 138, 296-307
Comparison of aluminium foams prepared by different methods using X-ray tomography
- 1 April 2018
- Published by Elsevier in Materials Characterization
- Vol. 138, 296-307
Comparison of aluminium foams prepared by different methods using X-ray tomography
- 22 April 2015
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 46 (4-5) , 462-476
Finite element simulation of arrays of hollow sphere structures
The numerical simulation of a repetitive model of a cellular metal is developed for fundamental investigation of the elastic behaviour of hollow sphere structures. Syntactic and partial morphologies of simple cubic configurations of hollow sphere structures are prescribed under boundary conditions corresponding to unit cells and periodic hollow sphere lattices. The obtained results are plotted as diagrams of Young's modulus versus relative density and allow to explain the behaviour of hollow sphere structures independent of their basic elastic properties.
- 22 April 2015
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 46 (4-5) , 462-476
Finite element simulation of arrays of hollow sphere structures
The numerical simulation of a repetitive model of a cellular metal is developed for fundamental investigation of the elastic behaviour of hollow sphere structures. Syntactic and partial morphologies of simple cubic configurations of hollow sphere structures are prescribed under boundary conditions corresponding to unit cells and periodic hollow sphere lattices. The obtained results are plotted as diagrams of Young's modulus versus relative density and allow to explain the behaviour of hollow sphere structures independent of their basic elastic properties.