EDEmmanuel Dubois

Emmanuel Dubois

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Emmanuel Dubois has a total of 92 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Toward Smart Probes for mmW On-Wafer Measurements: Advanced Packaging Using Laser Micromachining of Glass

    by Maya Alawar, Victor Fiorese, Sylvie Lépilliet, Daniel Gloria, Guillaume Ducournau, Emmanuel Dubois

    This article introduces the development of ground-signal-ground (GSG) probes for on-wafer active measurements, fabricated using femtosecond laser micromachining with a resolution between 5 and 10 $\mu $ m. The probes are made from a 100 $\mu $ m-thick Schott AF32 glass substrate bonded to a 10 $\mu $ m-thick nickel sheet, demonstrating enhanced mechanical durability and improved electrical performance. Nickel was selected for the tip contacts due to its superior mechanical hardness and electrical properties, which minimize contact resistance and extend probe lifespan. Mechanical testing showed that while glass-only probes failed at a contact force of 196 mN, nickel-glass probes withstood forces up to 667 mN. In addition, four-wire measurements confirmed low-resistance electrical contacts ( $0.05~\Omega $ above 6 mN) at a single contact point. Furthermore, this work introduces a glass interposer technology based on the same substrate material as the probe tips, enabling the integration of an amplified noise source (NS) based on 55 nm SiGe BiCMOS technology on a glass interposer. This approach mitigates dielectric and transition losses.Femtosecond laser micromachining was used to precisely structure the interconnects, allowing the NS to be integrated on the same substrate as the coplanar probing tips, thereby simplifying the signal propagation path. This system achieved a tunable available excess noise ratio (ENR $)_{\text {av}}$ level of up to 29 dB in the 140–170 GHz range, with constant output impedance matching better than −12 dB across the entire frequency band. Using the same glass carrier substrate enables the possibility of integrating the GSG probe tips with the NS chip into a smart active probe for on-wafer noise measurements.


  • Open Access

    Thermal characterization of Ge-rich GST thin films for phase change memories by Raman thermometry

    by Akash Patil, Yannick Le-Friec, Pascal Roussel, Yves Deblock, Simon Jeannot, Philippe Boivin, Emmanuel Dubois, Jean-François Robillard

    Doped GeSbTe (GST)-based phase change materials are of growing interest due to their ability to enable high-temperature data retention for embedded memory applications. This functionality is achieved through Ge enrichment and addition of dopants such as N and C in stoichiometries such as GST-225, which improve the crystallization temperature and thermal phase stability. In this study, we examine the effect of these dopants on thermal conductivity using Raman thermometry. We report the temperature-dependent thermal conductivity of the amorphous and crystalline phases of Ge-rich GeSbTe (GGST) and Ge-rich GeSbTe N-doped (GGSTN) thin films. The results reveal a surprising temperature dependence of the thermal conductivity of the crystalline phase of GGST and GGSTN, a phenomenon not typically observed for GST-based materials. Additionally, enrichment of Ge and subsequent N-doping result in reduced thermal conductivity, which can benefit the power consumption of phase change memories. From a characterization perspective, Raman thermometry has been developed as a technique for simultaneous structural and thermal characterization of GST-based materials.


  • Glass interposer for heterogeneous integration of flip-chipped photonic and electronic integrated circuits

    by Jean-Marc Boucaud, Cédric Durand, Frédéric Gianesello, Davide Bucci, Jean-Emmanuel Broquin, Emmanuel Dubois

    In this Letter, we propose an approach to improve the packaging of electro-optical transceivers based on silicon photonics through the development of a glass interposer. This assembly platform integrates polymer optical waveguides and an integrated turning mirror that vertically redirect the optical signal in the plane of the interposer to the grating coupler of a flip-chipped photonic integrated circuit (PIC). A distinctive feature of the proposed packaging scheme is to use a conventional flip-chip technique without active alignment. Functionalities are completed with a copper redistribution layer that supports the routing of DC to millimeter wave (mmW) signals to drive the PIC. The measured loss in polymer waveguides is 1.92 dB/cm at 1310 nm, and the coupling losses associated with light propagation through the turning mirror and the PIC grating coupler are 18.7 dB. Coplanar mmW waveguides are structured on the glass interposer by cold laser ablation, yielding an attenuation of 0.3 dB/mm at 58 GHz. The most important outcome of this work is that the coupling of the optical signal from the interposer to the PIC is experimentally established. We also assessed the mmW performance of coplanar waveguides through the validation of the interposer to PIC and PIC to the interposer transition.


  • Open Access

    Improvement of linearity in trap-rich substrates for radio frequency applications: Which of donor and acceptor trap is the best?

    by Justine Philippe, Jean-François Robillard, Daniel Gloria, Emmanuel Dubois

    This paper investigates the effect of volume traps intentionally introduced into a silicon-on-insulator (SOI) substrate by inserting a layer of polysilicon beneath buried oxide. In radio frequency applications, this type of substrate, referred to as trap-rich, is known to considerably reduce the generation of harmonics resulting from the parasitic non-linear charge dynamics introduced by the substrate handler under the buried oxide. This analysis focuses on a test vehicle in the form of an integrated coplanar waveguide on two types of substrates, namely, high-resistivity SOI substrates with and without a trap-rich layer. From a modeling point of view, a simulation methodology is implemented in order to convert the 3D simulation of the coplanar waveguide into a 2D treatment that takes into account the wave propagation effect associated with the distributed nature of the transmission line. As a first step, this modeling strategy is implemented to reproduce the effect of increasing substrate resistivity on 2nd and 3rd harmonic reductions, leading to an excellent agreement with experimental data. Building on this validation of the simulation method, we have opted to simulate the non-linear response of the transmission line on the SOI trap-rich substrate by simplifying the trap distribution model. To avoid the adoption of unverified and strongly process-dependent trap distributions across the bandgap, a midgap monovalent trap density has been introduced, either acceptor or donor density. A monovalent density of acceptor traps with a concentration of 1016 cm−3 and a carrier lifetime of 0.1 ns has been shown to reproduce the experimental data very accurately with a substantial reduction in 2nd and 3rd harmonics. A detailed analysis of the displacement current waveforms explains the beneficial role of acceptor traps compared with donor traps.


  • Analysis of Airgaps for OFF-State Capacitance Reduction in SOI-CMOS RF Switches

    by Daniel Gheysens, Alain Fleury, Stéphane Monfray, Frédéric Gianesello, Philippe Cathelin, David Troadec, Jean François Robillard, Emmanuel Dubois

    This article analyses the introduction of airgaps in the interconnect network of silicon-on-insulator (SOI)-CMOS-based RF switches to significantly reduce the OFF-state capacitance $\textit{C}_{\biosc{off}}$ without degrading the ON-state resistance $\textit{R}_{\biosc{on}}$ . Based on the 130-nm node of an existing RF-SOI-CMOS technology, an accurate $\textit{C}_{\biosc{off}}$ evaluation is performed by calculating the respective contributions of interconnects and the intrinsic transistor separately. The impact of the relative airgap volume is simulated and results in an ultimate $\textit{C}_{\biosc{off}}$ reduction of 24.6% when the intermetal dielectric is completely replaced by air. It is shown that most of the reduction in $\textit{C}_{\biosc{off}}$ is achieved by introducing airgap at the first metal level. The airgap approach is verified experimentally by partially eliminating the interconnect dielectric of RF switches in postprocess etching steps. A measured $\textit{C}_{\biosc{off}}$ improvement of 21.7 (7.2%) and 18.3 fF/mm (6.3%) is demonstrated for 0.14-and 0.16- $\mu$ m gate length transistors, for which the airgap volume is only partial.


  • A G-Band Packaged Amplified Noise Source Using SiGe BiCMOS 55-nm Technology

    by Victor Fiorese, João Carlos Azevedo Gonçalves, Simon Bouvot, Sylvie Lépilliet, Daniel Gloria, Guillaume Ducournau, Christophe Gaquière, Emmanuel Dubois

    This article introduces the first BiCMOS SiGe technology-based packaged noise source (NS) operating in the $G$ -band (140–220 GHz). An amplified p-n junction diode has been packaged and biased in avalanche mode to generate excess noise ratios (ENRs $_{\mathrm{av}})$ of approximately 25 dB between 140 and 170 GHz at package output for an unbiased low state and a high state corresponding to a 20-mA cathode current. The two-stage amplifier is a cascode cell composed of two BiCMOS 55-nm NPN very high speed (NPNVHS) transistors with an emitter length and a width of 5.56 and 0.2 $\mu$ m, respectively. An optimal biasing results in a 8.2-mA current consumption for one cascode stage and an overall available power gain ( $G_{\mathrm{av}})$ better than 12 dB between 140 and 180 GHz. This supports operation in a low state, where the diode is unbiased and the amplifier is biased, which constitutes a scheme that easily validates the minimum detectable signal (MDS) condition while exhibiting a 14-dB ENR $_{\mathrm{av}}$ level in the beginning of $G$ -band compared to this polarized low state. This NS shows a monitorable $P_{\mathrm{COLD}}$ and is adaptable to several noise receivers. In addition, the ENR $_{\mathrm{av}}$ level flatness is better than 3 dB over the entire frequency range, and the impedance matching, better than $-$ 7.5 dB at package output, is not dependent on the NS bias condition. Noise figure (NF) extraction of a WR05-connectorized III–V amplifier MPA04-1 from Virginia Diodes, Inc. (VDI) was performed and compared to the ELVA ISSN-05 commercial NS measurement, showing low discrepancy. The same study was performed on-wafer for an NPNVHS transistor on BiCMOS 55-nm technology, showing a maximum discrepancy of 0.8 dB between the two measured NFs. The NF measurement accuracy of the MPA04-1 amplifier was assessed up to 220 GHz, by varying the chosen high state while keeping the low state completely unbiased. A maximum 0.5-dB variation over 12 obtained NF values is observed up to 200 GHz.


  • Open Access

    Design and fabrication of nanometer measurement platform for better understanding of silicon mechanical properties

    by Maciej Haras, Jean-François Robillard, Thomas Skotnicki, Emmanuel Dubois

    Semiconductor industry is experiencing unprecedented growth, still driven by Moore's law, which is continually delivering devices with improved performance at lower costs. The continuation of this development places the industry in a divergent trade-off between economic attractiveness, technological feasibility, and the need for further performance improvement. Since the mainstream semiconductor technologies are silicon-based, new disruptive innovations are needed to gain additional performance margins. The use of nanowires is the preferred approach for preserving electrostatic control in the MOS transistor channel, and the application of mechanical stress is a booster of carrier mobility. It is in this context that this paper presents the design, fabrication, theoretical modeling, and characterization of a measurement platform to characterize the mechanical tensile stress of extremely narrow Si nanowires as small as 14.2 ± 1.12 nm in width. The proposed measurement platform enables a precise control of uniaxial strain, in terms of both amplitude and location, through the implementation of a stoichiometric Si3N4 pulling strand exerting a high tensile force on silicon nanowires. Reported devices are fabricated using a silicon-on-insulator wafer with fully complementary metal–oxide–semiconductor-compatible processing and top-down approach. It is observed that the mechanical strength of nanostructured Si is size-dependent and increases with miniaturization. Characterization revealed a record tensile strength value of 7.53 ± 0.8% (12.73 ± 1.35 GPa) for the narrowest nanowires fabricated using a top-down approach.

  • Open Access

    Single-Crystal Silicon Thermoelectrics by Phonon Engineering

    by Thierno-Moussa Bah, Stanislav Didenko, Di Zhou, Tianqi Zhu, Hafsa Ikzibane, Stephane Monfray, Thomas Skotnicki, Emmanuel Dubois, Jean-François Robillard

    Herein, we report the use of nanostructured crystalline Si as a thermoelectric material and its integration into thermoelectric harvesters. The proof-of-concept relies on the partial suppression of lattice thermal transport by introducing pores with dimensions scaling between the electron mean free path and the phonon mean free path. In other words, we artificially aimed at the electron crystal phonon glass tradeoff targeted for thermoelectric efficiency. The devices were fabricated using CMOS compatible processes and exhibited power generation from a few microWatts per cm^2 to a few milliWatts per cm^2 under temperature differences from a few K to 200 K across the thermopiles. These numbers demonstrate the capability to power autonomous devices with environmental or body heat using silicon chips with areas below cm^2. This paper also reports the possibility of using the developed demonstrators for integrated thermoelectric cooling.

  • Open Access

    Heat dissipation in partially perforated phononic nano-membranes with periodicities below 100 nm

    by Antonin M. Massoud, Valeria Lacatena, Maciej Haras, Emmanuel Dubois, Stéphane Monfray, Jean-Marie Bluet, Pierre-Olivier Chapuis, Jean-François Robillard

    Understanding how thermal-phonon paths can be shaped is key for controlling heat dissipation at the nanoscale. Thermophononic crystals are periodic porous nanostructures with thermal conductivity deviating from effective medium theory, which is possible if the characteristic sizes are of the order of phonon mean free paths and/or if phonons are forced to flow in privileged directions. We investigate suspended silicon nanomembranes with a periodic array of partially perforated holes of original paraboloid shape, with all characteristic lengths below 100 nm. Results from scanning thermal microscopy, a thermal sensing technique derived from atomic force microscopy, indicate that partial perforation of the membranes impacts heat conduction moderately, with the holey crystals showing a thermal conductivity reduction by a factor 6 in comparison to the bulk and a factor 2.5 in comparison to the non-perforated membrane. The impact of the phononic shapes is analyzed in light of a complementary Monte Carlo ray-tracing estimate of the effective phonon mean free paths that include multiple phonon reflection and highlights phonon backscattering.


  • Open Access

    Mitigation of substrate coupling effects in RF switch by localized substrate removal using laser processing

    by Arun Bhaskar, Justine Philippe, Etienne Okada, Flavie Braud, Jean-Francois Robillard, Cédric Durand, Frédéric Gianesello, Daniel Gloria, Christophe Gaquiere, Emmanuel Dubois

    Mitigation of substrate coupling effects in RF switch by localized substrate removal using laser processing