MMMuhammad M. Mirza

Muhammad M. Mirza

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Muhammad M. Mirza has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    THz intersubband electroluminescence from n-type Ge/SiGe quantum cascade structures

    by David Stark, Muhammad Mirza, Luca Persichetti, Michele Montanari, Sergej Markmann, Mattias Beck, Thomas Grange, Stefan Birner, Michele Virgilio, Chiara Ciano, et al.

    We report electroluminescence originating from L-valley transitions in n-type Ge/Si0.15Ge0.85 quantum cascade structures centered at 3.4 and 4.9 THz with a line broadening of Δ f / f ≈ 0.2 . Three strain-compensated heterostructures, grown on a Si substrate by ultrahigh vacuum chemical vapor deposition, have been investigated. The design is based on a single quantum well active region employing a vertical optical transition, and the observed spectral features are well described by non-equilibrium Green's function calculations. The presence of two peaks highlights a suboptimal injection in the upper state of the radiative transition. Comparison of the electroluminescence spectra with a similar GaAs/AlGaAs structure yields one order of magnitude lower emission efficiency.


  • Well Integrity Issues in Steam Flood Injection Wells, Karim Small Field Cluster

    by Alexis Ariwibowo, Al Salt Al Sulti, Yousuf Al Aufi, Muhammad Mirza

    Two (2) steam flood vertical injection wells are under operation for the last 15 months in a two- pattern pilot. Previous steam injection experience in this reservoir did not indicate serious issues due to the short injection periods for cyclic steam stimulation (CSS) but several well integrity issues have been faced during the steam flood period. Key issues include high wellhead growth, steam leak to the annulus A, annulus between 7” production casing and 4-1/2” injection tubing, and groundwater vapor behind 9.625” surface casing. Negative impacts from these issues on the continuity and effectiveness of the steam flood are recognized and need to be resolved comprehensively. All wells in the steam flood pilot were drilled and completed based on designs and procedures according to thermal well compliance including well equipment, and cementing specification. Production casing was equipped with thermal expansion collars to support reduction in wellhead growth. Completion strategy uses seal bore packer with bore extensions to accommodate tubing movement and Vacuum-Insulated-Tubing to provide maximum thermal insulation. However, the presence of a total- loss zone near the surface (starting from 50 m depth) affects the cement isolation between surface casing and 12.25” open hole. Daily monitoring is performed on each well where key injection parameters and well responses are recorded. Maximum wellhead growth reached 61 cm within the first week and steam leak from the injection string to annulus A started after 6 months of steam injection. Soon after that, groundwater vapor starts to arise from the gap between 9.625” casing and 12.25” open hole. These series of failures occurred in both injection wells within 3 months apart from each other. It is believed that the steam leak to annulus A resulted in thermal transmission to groundwater vapor. Hoist entries to both injectors indicated that Injector-1 has tubing seal assembly stuck inside seal bore and resulted in parted tubing collar while Injector-2 has tubing seal assembly damage. Both wells have thick oil covering the retrieved seal bore packer. Remedial actions were performed, including a complete change-out of the seal bore packer assembly and top-job cement fill up to surface using fast-set cement to isolate the gap between 9.625” casing and 12.25” open hole to reduce wellhead growth. As a result, the maximum wellhead growth became only 19 cm and 4 cm in Injector-1 and Injector-2, respectively. These remedial actions also led to restoring well and thermal integrity. Retrieved seal bore packer was sent back to manufacturer for appropriate failure analysis and providing useful feedback reports on the above issues. Monitoring and observation data along with failure analysis should provide vital information and possible improvement in completion strategy for steam injection wells that are planned for continuous steam flood projects in similar reservoirs.


  • Top Cited Papers
    Open Access

    High performance planar germanium-on-silicon single-photon avalanche diode detectors

    by Peter Vines, Kateryna Kuzmenko, Jarosław Kirdoda, Derek C. S. Dumas, Muhammad M. Mirza, Ross W. Millar, Douglas J. Paul, Gerald S. Buller

    Single-photon detection has emerged as a method of choice for ultra-sensitive measurements of picosecond optical transients. In the short-wave infrared, semiconductor-based single-photon detectors typically exhibit relatively poor performance compared with all-silicon devices operating at shorter wavelengths. Here we show a new generation of planar germanium-on-silicon (Ge-on-Si) single-photon avalanche diode (SPAD) detectors for short-wave infrared operation. This planar geometry has enabled a significant step-change in performance, demonstrating single-photon detection efficiency of 38% at 125 K at a wavelength of 1310 nm, and a fifty-fold improvement in noise equivalent power compared with optimised mesa geometry SPADs. In comparison with InGaAs/InP devices, Ge-on-Si SPADs exhibit considerably reduced afterpulsing effects. These results, utilising the inexpensive Ge-on-Si platform, provide a route towards large arrays of efficient, high data rate Ge-on-Si SPADs for use in eye-safe automotive LIDAR and future quantum technology applications.


  • Open Access

    Variability study of high current junctionless silicon nanowire transistors

    by Vihar P. Georgiev, Alexandru-Iustin Dochioiu, Fikru-Adamu Lema, Salim Berada, Muhammad M. Mirza, Douglas J. Paul, Asen Asenov

    Silicon nanowires have numerous potential applications, including transistors, memories, photovoltaics, biosensors and qubits [1]. Fabricating a nanowire with characteristics required for a specific application, however, poses some challenges. For example, a major challenge is that as the transistors dimensions are reduced, it is difficult to maintain a low off-current (Ioff) whilst simultaneously maintaining a high on-current (Ion). This can be the result of quantum mechanical tunnelling, short channel effects or statistical variability [2]. A variety of new architectures, including ultra-thin silicon-on-insulator (SOI), double gate, FinFETs, tri-gate, junctionless and gate all-around (GAA) nanowire transistors, have therefore been developed to improve the electrostatic control of the conducting channel. This is essential since a low Ioff implies low static power dissipation and it will therefore improve power management in the multi-billion transistor circuits employed globally in microprocessors, sensors and memories.


  • Open Access

    One dimensional transport in silicon nanowire junction-less field effect transistors

    by Muhammad M. Mirza, Felix J. Schupp, Jan A. Mol, Donald A. MacLaren, G. Andrew D. Briggs, Douglas J. Paul

    Junction-less nanowire transistors are being investigated to solve short channel effects in future CMOS technology. Here we demonstrate 8 nm diameter silicon nanowire junction-less transistors with metallic doping densities which demonstrate clear 1D electronic transport characteristics. The 1D regime allows excellent gate modulation with near ideal subthreshold slopes, on- to off-current ratios above 108 and high on-currents at room temperature. Universal conductance scaling as a function of voltage and temperature similar to previous reports of Luttinger liquids and Coulomb gap behaviour at low temperatures suggests that many body effects including electron-electron interactions are important in describing the electronic transport. This suggests that modelling of such nanowire devices will require 1D models which include many body interactions to accurately simulate the electronic transport to optimise the technology but also suggest that 1D effects could be used to enhance future transistor performance.