Karla Judith Moreno has a total of 110 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of astaxanthin concentration on the wear properties of castor oil and wear rate prediction using non-linear regression by pin-on-disk tests

    by Sandra Rojas Osorio, Marco Ulises Negrete Ríos, María Teresa Hernández Sierra, Karla Judith Moreno Bello

    Numerous studies have aimed to identify biodegradable oils and additives as alternatives to mineral substances in industrial settings. Among these, castor oil combined with astaxanthin, a natural antioxidant, has demonstrated exceptional results compared to other substances. Consequently, this study examined the tribological performance of five mixtures of castor oil with different astaxanthin concentrations using sliding friction tests in a pin-on-disk tribometer based on the ASTM G99-23. For this purpose, steel disks of AISI 4140 and spheres of tungsten carbide (WC) with a diameter of 3 mm were used as counterparts. Each essay was performed by immersing the test specimens in the lubricant, controlling the temperature at 100 °C. The key finding is that the reduction in wear rate is directly affected by increasing astaxanthin concentration, which was observed in the wear mechanism. The correlation between wear rate and astaxanthin concentration was studied through a mathematical equation that estimates the value of the wear parameter at antioxidant concentrations beyond those tested experimentally. This achievement marks a significant milestone in applying statistics to complex systems, establishing a mathematical link between astaxanthin concentrations and wear properties.

  • Comprehensive evaluation of canola oil with natural additives for hydraulic applications: tribological, rheological and contact angle measurements

    by Marco Ulises Negrete Rios, Sandra Rojas-Osorio, María Teresa Hernández-Sierra, Karla J. Moreno

    Purpose: This study aims to evaluate the tribological performance of canola oil-based hydraulic fluids of viscosity grade 32 (ISO VG32), enhanced with natural antioxidants – eugenol, curcumin and ascorbic acid. Design/methodology/approach: The formulations were prepared with 0.5 wt.% of each additive and benchmarked against a commercial mineral ISO VG32 oil. Physical properties (density, viscosity, viscosity index), tribological behavior (friction coefficient, wear rate, lubricant efficiency), wettability and the lubricant’s final condition after friction tests were analyzed using standardized ASTM methodologies. Findings: Results revealed that vegetable-based formulations exhibited higher viscosity indices (up to 41% higher than mineral oil), thereby improving stability under temperature variations. Tribological tests demonstrated lower friction coefficients and enhanced lubricant efficiency compared to mineral oil, with the canola oil/ascorbic acid blend showing the most favorable performance (friction reduction of 43% and wear rate reduction of 99%). Contact angle analysis confirmed cohesive molecular behavior. Originality/value: The incorporation of natural antioxidants significantly improved the oxidative and tribological stability of canola oil, positioning these bio-lubricants as eco-friendly, high-performance alternatives to mineral hydraulic fluids. Only a few researchers evaluate the influence of additives on wettability and explore their impact on the tribological behavior in bio-hydraulic formulations.

  • Open Access

    Enhanced Tribological Properties of Castor and Sesame Oil Mixture with Ascorbyl Palmitate for Boundary Lubrication

    by Sandra Rojas-Osorio, Marco Ulises Negrete-Ríos, José E. Báez, María Teresa Hernández-Sierra, Karla J. Moreno

    Vegetable oil blends significantly improve friction and wear performance compared to individual oils. However, the oxidizing nature of these blends remains a consistent challenge. Currently, both natural and synthetic antioxidants are recommended to address this issue. This study investigated the use of ascorbyl palmitate as a natural additive in a previously evaluated mixture of castor and sesame oils, focusing on its tribological performance in an AISI 4140/AISI 52100 tribopair. The chemical composition of the biolubricants was analyzed using Fourier-transform infrared spectroscopy (FTIR), while the physical properties such as density and kinematic viscosity were measured at various temperatures. To evaluate their suitability for tribological applications, their friction and wear performance were assessed using a ball-on-disk tribometer. The friction coefficient, coefficient of lubrication efficiency (CLE), and wear behavior (volume loss, wear rate, and wear mechanism) were analyzed. This study demonstrates a notable enhancement in the tribological properties of the binary mixture with varying ascorbyl palmitate concentrations (0.25, 0.5, and 0.75 wt.%). The addition of ascorbyl palmitate reduces wear by forming protective interfacial layers, resulting in a low friction coefficient of 0.07 and a 46% reduction in volume loss. Some concentrations of ascorbyl palmitate also mitigated the severity of the wear mechanism.


  • Open Access

    Integrity of 316/420 Stainless Steel Tribosystem Under Severe Marine Conditions

    by Karla J. Moreno, María Teresa Hernández-Sierra, J. Santos García-Miranda, Luis Daniel Aguilera-Camacho

    The present study aims to examine the tribological and mechanical integrity of AISI 316/420 stainless steel tribosystem under boundary lubrication with artificial seawater for application in a marine environment. The tribological performance was evaluated through sliding friction tests using a ball-on-disc configuration, at contact pressures ranging from 520 MPa to 1400 MPa. The influence of working contact pressure on the kinetic friction coefficient (µk), wear rate (K), and worn surface damage was studied. Their interaction with the corrosive medium was evaluated using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analyses to investigate the wear mechanisms. Microhardness testing was also employed to assess the effect of friction and wear on the mechanical properties of the tribosystem. The results showed that friction and microhardness increased with contact pressure, while the wear rate decreased due to strain hardening. The wear mechanisms included abrasion, adhesion, delamination, and localized oxidation. This study offers new perspectives on the tribological response of stainless steel materials in marine engineering systems, providing valuable insights for material selection and design in corrosive and high-load applications.


  • Open Access

    Evaluation of Aromatic Organic Compounds as Additives on the Lubrication Properties of Castor Oil

    by María Teresa Hernández-Sierra, José E. Báez, Luis Daniel Aguilera-Camacho, J. Santos García-Miranda, Karla J. Moreno

    In the quest for sustainable lubrication solutions, the present research explored the potential of five organic compounds as additives in castor oil (CO) to improve its lubricating properties. The compounds tested were curcumin, eugenol, 1,3-Diphenyl-2-propanone, 1,3-Diphenyl-2-propenone, and 1,3-Diphenyl-1,3-propanedione. The main results showed that each additive enhanced at least one characteristic of CO. Most of the additives lowered the density of the castor oil but increased the viscosity by up to 20%. Curcumin and eugenol were particularly effective in creating thicker lubricant films and higher film thickness ratios. Eugenol and 1,3-Diphenyl-2-propanone significantly reduced the friction coefficient by up to 25%. Wear rate and wear mechanisms were significantly reduced with all the additives, achieving a reduction in wear rate of up to 50% (CO+curcumin). All the additives, except the 1,3-Diphenyl-1,3-propanedione, enhanced the oxidation onset temperature up to 8 °C. The influence of chemical structure was also addressed. The optimal additive combination for a specific application that demands minimal friction and wear, as well as strong oxidation stability, was eugenol, followed by curcumin and 1,3-Diphenyl-2-propanone. Overall, the research contributes to the development of eco-friendly lubricants, aligning with the growing demand for green industrial applications, and highlights the significant tribological benefits of these substances as sustainable additives in biolubricant formulations.


  • Open Access

    A Comparative Analysis of the Lubricating Performance of an Eco-Friendly Lubricant vs Mineral Oil in a Metallic System

    by J. Santos García-Miranda, Luis Daniel Aguilera-Camacho, María Teresa Hernández-Sierra, Karla J. Moreno

    Eco-friendly lubricant research continues to increase since it has a comparative performance to commercial mineral lubricants to overcome the effects of environmental impact. However, the efficiency of these green lubricants depends on specific applications. In this study, we analyzed the friction and wear performance of a castor/sesame oil mixture as an eco-friendly lubricant and its comparison to a commercial mineral lubricant tested in a metallic system employed in bearing elements. For this purpose, AISI 8620 steel against ISO 100Cr6 was used as tribological pair. The friction and wear tests were carried out through a Tribometer of ball-on-disk configuration under boundary lubricating conditions, whereas the worn surfaces were investigated by using optical and electron microscopy. The physical properties and the rheological properties of the lubricants were also determined. The friction and wear performance between the eco-friendly lubricant and mineral oil were similar so that the CLE were comparable. The CLE values in terms of friction and wear ranged from 86% to 99.4%, respectively.


  • Open Access

    Sustainable xanthophylls-containing poly(ε-caprolactone)s: synthesis, characterization, and use in green lubricants

    by Eloy Rodríguez-Deleón, Moustapha Bah, José E. Báez, María T. Hernández-Sierra, Karla J. Moreno, Alejandro Nuñez-Vilchis, José Bonilla-Cruz, Kenneth J. Shea

    Three xanthophylls [(3R,3′R,6′R)-lutein (1), (3R,3′S)-zeaxanthin (2), and (3R,3′S)-astaxanthin (3)] were used for the first time as initiators in the ring-opening polymerization (ROP) of ε-caprolactone (CL) catalyzed by tin(II) 2-ethylhexanoate [Sn(Oct)2] for the synthesis of novel sustainable xanthophyll-containing poly(ε-caprolactone)s (xanthophylls-PCL). The obtained polyesters were characterized by 1H and 13C NMR, FT-IR, DSC, SEC, and MALDI-TOF MS, and their use as additives in green lubricants was evaluated using a sliding friction test under boundary conditions. Xanthophylls-PCL were obtained with good conversions and with molecular weights determined by SEC to be between 2500 and 10 500 Da. The thermal properties of xanthophyll-polyesters showed a crystalline domain, detected by DSC. Lastly, the green lubricant activity of these polymers was evaluated and the results showed that xanthophylls-PCL could be employed as additives for biodegradable lubricant applications since they have better tribological behavior than current additives, which demonstrates their potential as future commercial materials with interesting eco-friendly properties for diverse applications.


  • Friction and wear improvement by using Curcumin as a natural additive in green lubricants

    by María Teresa Hernández-Sierra, José E Báez, Luis Daniel Aguilera-Camacho, J Santos García-Miranda, Karla J Moreno

    Lubrication is an essential mechanism to make machines and engines more efficient by lowering friction and wear. Despite this, to mitigate environmental damage, lubricants must come from renewable sources and be biodegradables. Therefore, this study analyzed the use of Curcumin as a natural additive in two green oils to improve their tribological and oxidative performance. The density and viscosity of lubricants with and without curcumin additive, as well as the lubrication regime, were determined. The operational performance was analyzed by tribological tests under a ball-on-disk configuration at 100°C based on the ASTM G99. The oxidative behavior of lubricants was examined by studying the IR bands for primary and secondary oxidative products, as well as by DSC-TGA techniques for evaluating the Oxidation Onset Temperature and the thermogravimetric behavior. At the studied conditions, the incorporation of Curcumin into the oils increased the viscosity of the lubricants up to 46%, the friction coefficient decreased up to 70%, and wear was diminished up to 96%, despite working in boundary lubrication. Moreover, the addition of curcumin noticeably enhanced the oxidation behavior of lubricants. The results of this research suggest that Curcumin is an excellent option to improve the physical properties, operational performance, and oxidative stability of green oils to create effective and environmentally friendly lubricants.


  • Open Access

    Tribological Performance of 100Cr6/8620 Steel Bearing System under Green Oil Lubrication

    by Ricardo Ortega-Álvarez, María T. Hernández-Sierra, Luis D. Aguilera-Camacho, Micael G. Bravo-Sánchez, Karla J. Moreno, J. Santos García-Miranda

    There is a great need to perform all processes and services more efficiently to reduce energy consumption and material waste. Bearing systems are present in all machines and motors, playing an important role in the reduction of energy consumption. 100Cr6 (ISO 683-17:2014) and AISI 8620 are two typical steels employed in most bearing systems. However, improving the tribological performance of these steels is still required. This study reports the analysis of green lubricants based on mixtures of vegetable oils to improve the friction and wear properties of steel bearing systems. Firstly, a method is presented to identify potential mixtures based on the excess thermodynamic properties. Then, the tribological performance of the 100Cr6/8620 steel bearing system lubricated with the selected mixtures is evaluated by the ball-on-disk method. It was found that the friction and wear behavior of the 100Cr6/8620 steel bearing system can be notably improved by the utilization of oil mixtures rather than pure green oils. The kinetic friction coefficient decreased up to 10% with the ideal mixture of castor and sesame oil, while wear was reduced up to 81% with the ideal mixture of castor and canola oil. Therefore, we suggest that vegetable oil blends may be a good option for the feasible manufacture of biolubricants for bearing systems.


  • Open Access

    On the Tribological and Oxidation Study of Xanthophylls as Natural Additives in Castor Oil for Green Lubrication

    by Karla J. Moreno, María Teresa Hernández-Sierra, José E. Báez, Eloy Rodríguez-Deleón, Luis Daniel Aguilera-Camacho, J. Santos García-Miranda

    The present study focuses on an introductory analysis of the use of three xanthophylls as additives for green lubricant applications. For this purpose, the additives were characterized by FTIR and 1H-NMR techniques, and the bio-lubricants were described by their physical properties. The effect of the natural compounds on the friction and wear properties of bio-lubricants were evaluated by sliding friction tests under boundary conditions, as confirmed by an analysis of the lubricating film thickness. The antioxidant capacity was analyzed by FTIR spectroscopy. It was observed better wear protection in castor oil with xanthophylls than without these additives. The wear rate was reduced up to 50% compared with neat oil. Lesser beneficial effects were appreciated in friction coefficient since it was increased 25%. The best contribution was observed with astaxanthin as an additive. In addition, a significant improvement in the oxidation of castor oil, complemented with this additive, was exhibited by FTIR analysis. It was found that xanthophylls could be employed as additives for totally biodegradable lubricant applications since they have better tribological and antioxidant behavior than current additives.