Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Shaheen A. Al-Muhtaseb has a total of 98 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Roles of Polymerization Temperature and Initiator Type on Thermal Properties of Rubitherm® 21 PCM Microcapsules

    by Refat Al-Shannaq, Monzer Daoud, Mohammed Farid, Wasi Ahmad, Shaheen A. Al-Muhtaseb, Mazhar Ul-Islam, Abdullah Al Saidi, Imran Zahid

    Thermal energy storage offers a viable solution for managing intermediate energy availability challenges. Phase change materials (PCMs) have been extensively studied for their capacity to store thermal energy when available and release it when needed, maintaining a narrow temperature range. However, effective utilization of PCMs requires its proper encapsulation in most applications. In this study, microcapsules containing Rubitherm®(RT) 21 PCM (Tpeak = 21 °C, ΔH = 140 kJ/kg), which is suitable for buildings, were synthesized using a suspension polymerization technique at different operating temperatures (45–75 °C). Two different water-insoluble thermal initiators were evaluated: 2,2-Azobis (2,4-dimethyl valeronitrile) (Azo-65) and benzoyl peroxide (BPO). The prepared microcapsules were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), particle size distribution (PSD), scanning electron microscope (SEM), and optical microscopy (OM). Additionally, the microcapsules were subjected to multiple melting and freezing cycles to assess their thermal reliability and performance stability. DSC results revealed that the microcapsules using BPO exhibited a latent heat of melting comparable to those produced with Azo-65 at an operating temperature of 75 °C. However, the onset crystallization temperature for the BPO-encapsulated PCMs was approximately 2 °C lower than that of the Azo-65-encapsulated PCMs. The greatest latent heat of melting, 107.76 J/g, was exhibited by microcapsules produced at 45 °C, representing a PCM content of 82 wt. %. On the other hand, microcapsules synthesized at 55 °C and 75 °C showed latent heats of 96.02 J/g and 95.66 J/g, respectively. The degree of supercooling for PCM microcapsules was reduced by decreasing the polymerization temperature, with the lowest supercooling observed for microcapsules synthesized at 45 °C. All microcapsules exhibited a monodisperse and narrow PSD of ~10 µm, indicating uniformity in microcapsule size and demonstrating that temperature variations had no significant impact on the particle size distribution. Future research should focus on low-temperature polymerization with extended polymerization times.


  • Top Cited Papers
    Open Access

    Climate Change and Energy Security: A Comparative Analysis of the Role of Energy Policies in Advancing Environmental Sustainability

    by Ahmed Elkhatat, Shaheen Al-Muhtaseb

    This review analyzes the complex relationship between climate change and energy security and their joint impact on global development. It emphasizes the need for sustainable energy solutions to tackle increasing global warming effects and energy demands. A thorough literature analysis highlights the link between energy policies, climate goals, and sustainable development aspirations. Moreover, it examines the effectiveness of energy policies in various national contexts in promoting environmental sustainability and emphasizing regional dynamics, socio-economic factors, and diverse energy planning approaches. The review explains the multifaceted relationship between climate change, energy security, and environmental protection. Key recommendations related to renewable energy transitions are provided as crucial means to address global energy demand and resource constraints while reducing dependence on fossil fuels. The analysis underscores renewable energy’s key role in aligned energy strategies that balance security and sustainability for a low-carbon future. It emphasizes the critical need for coordinated policies, technological innovation, and collaborative action between academia, industry, and policymakers to advance integrated energy systems and thermal storage solutions.


  • Open Access

    Investigation of palladium catalysts in mesoporous silica support for CO oxidation and CO2 adsorption

    by Rola Mohammad Al Soubaihi, Khaled Mohammad Saoud, Ahmed Awadallah-F, Ahmed Mohamed Elkhatat, Shaheen A. Al-Muhtaseb, Joydeep Dutta


  • Open Access

    Combined “Renewable Energy–Thermal Energy Storage (RE–TES)” Systems: A Review

    by Ahmed Elkhatat, Shaheen A. Al-Muhtaseb

    Current industrial civilization relies on conventional energy sources and utilizes large and inefficient energy conversion systems. Increasing concerns regarding conventional fuel supplies and their environmental impacts (including greenhouse gas emissions, which contribute to climate change) have promoted the importance of renewable energy (RE) sources for generating electricity and heat. This comprehensive review investigates integrating renewable energy sources (RES) with thermal energy storage (TES) systems, focusing on recent advancements and innovative approaches. Various RES (including solar, wind, geothermal, and ocean energy sources) are integrated with TES technologies such as sensible and latent TES systems. This review highlights the advantages and challenges of integrating RES and TES systems, emphasizing the importance of hybridizing multiple renewable energy sources to compensate for their deficiencies. Valuable outputs from these integrated systems (such as hydrogen production, electric power and freshwater) are discussed. The overall significance of RES–TES hybrid systems in addressing global energy demand and resource challenges is emphasized, demonstrating their potential to substitute fossil-fuel sources. This review provides a thorough understanding of the current state of RES–TES integration and offers insights into future developments in optimizing the utilization of renewable energy sources.


  • Advancing students' trouble shooting skills with open‐ended questions and computer‐aided learning using Aspen Plus® in a multistage lab experiment

    by Ahmed M. Elkhatat, Shaheen A. Al‐Muhtaseb

    Open‐ended questions and a computer‐aided learning approach using the Aspen Plus® Sensitivity Analysis Tool (OEQ‐CAL/APSAT) was used to simulate a multistage lab experiment of a piping system (consisting of pumps, pipes, and valves) as part of the Fluid Dynamics and Heat Transfer Laboratory course delivered within the Qatar University's curriculum for the Bachelor of Science degree in Chemical Engineering. To evaluate the learning goals of this approach, three‐stage experiments were used. Results indicated that students gained a deep understanding of the material and showed a strong interest, demonstrated by the student's participation in the OEQ‐CAL/APSAT activity. As the complexity and realistic nature of cases being studied can be increased using this approach, laboratory courses can be taught more effectively, and the corresponding investigations can be expanded with virtual experiments. In addition, it is a practical choice to maximize the use of resources and an effective replacement for laboratory experiments in case of pandemics, confinement, or interest in testing the effects of hazardous conditions to ensure sustained learning outcomes.


  • Open Access

    Utilizing Thermal Energy for Crosslinking Gels: A Novel Rapid Approach

    by Ahmed Awadallah-F, Shaheen A. Al-Muhtaseb

    A novel route was invented for utilizing thermal energy (at an elevated temperature of 110 ± 2 °C) to synthesize and crosslink gels from resorcinol and formaldehyde without using catalysts or buffers. The outcome gels are identified by various techniques such as Fourier transform infrared, Raman spectroscopy, thermal gravimetric analysis, X-ray diffraction, nano-scanning electron microscopy, energy-dispersive X-ray spectroscopy and surface area and porosity analyses. Resorcinol–formaldehyde gels prepared by this approach are also carbonized and activated to study their subsequent activated carbons. The gels and their corresponding activated carbons expose hierarchical pore structures with micro-, meso- and macroporous features. The average pore sizes of gels and activated carbons ranged from 3.5 to 62.9 nm and from 0.9 to 2.0 nm, respectively. The total surface areas of gels and activated carbons ranged from 0.01 to 176.15 and from 160.93 to 511.46 m2/g, respectively. Moreover, the total pore volumes of gels and activated carbons ranged from 0 to 0.546 and from 0.086 to 0.366 cm3/g, respectively. The results refer to how this novel approach could be used in the synthesis of resorcinol–formaldehyde gels in particular, and might be used in the synthesis of other gels in general. Due to the absence of added catalysts or buffers, this approach yields clean products that can be valuable in various sensitive applications such as biomaterials and pharmaceuticals, which require no impurities from extra reacting species.


  • Open Access

    Carbon Capture from Post-Combustion Flue Gas Using a State-Of-The-Art, Anti-Sublimation, Solid–Vapor Separation Unit

    by Hani Ababneh, Ahmed AlNouss, Shaheen A. Al-Muhtaseb

    This work attempts to address the quest of removing carbon dioxide from flue gas streams to help preserve the environment. It is based on a model that is able to describe the solid-liquid-vapour and solid-vapour phase equilibria for the ternary system of N2-O2-CO2 at pressures from 5 to 130 bar and over a wide range of temperature (140 to 220 K). Furthermore, a corresponding state-of-the art solid-vapor (SV) CO2 capture/separation unit is developed and introduced in this work. The SV unit was modeled using the Aspen Custom Modeler software by implementing the thermodynamic model developed before. It was then simulated using the Aspen Plus simulator; its performance was studied and analyzed. Moreover, the performance of the unit was optimized and compared to the most conventional corresponding technology used by the industry (i.e., amine-scrubbing). Results proved that for the same output clean gas composition, which contains only 0.3% CO2, the developed state-of-the-art SV unit consumes almost half of the energy required by the conventional process. Other advantages of the novel SV separation unit include the lower requirement of capital equipment, no need of additional agents (such as solvents) and the avoidance of product contamination with such additional agents.


  • Open Access

    Virtual mimic of lab experiment using the computer‐based Aspen Plus® Sensitivity Analysis Tool to boost the attainment of experiment's learning outcomes and mitigate potential pandemic confinements

    by Ahmed M. Elkhatat, Shaheen A. Al‐Muhtaseb

    The computer‐based Aspen Plus® Sensitivity Analysis Tool (APSAT) was used as a virtual environment to mimic a gas absorption lab experiment in the Unit Operations Lab within the curriculum for the Bachelor of Science in Chemical Engineering at Qatar University. A pool of 35 students enrolled in three lab sections was utilized. The approach was applied in three stages to foster the attainment of the learning outcomes of the experiment by testing and evaluating some parameters that cannot be examined using the physical lab equipment. Results show that the approach helped the students gain a profound understanding and address conceptual mistakes while discussing the results of the APSAT outputs. Students who were engaged in the APSAT activity demonstrated a strong interest in this approach. This approach can be implemented to facilitate the teaching of lab courses. Furthermore, it is a practical choice to optimize the resources and a good substitute for lab experiments in case of any pandemic, confinement or interest in testing the effects of hazardous conditions to ensure sustaining the learning outcomes from corresponding experiments.


  • Open Access

    Natural Gas Sweetening Using an Energy-Efficient, State-of-the-Art, Solid–Vapor Separation Process

    by Hani Ababneh, Ahmed AlNouss, Iftekhar A. Karimi, Shaheen A. Al-Muhtaseb

    With the anticipated rise in global demand for natural gas (NG) and liquefied natural gas (LNG), sour gas reserves are attracting the attention of the gas industry as a potential resource. However, to monetize these reserves, sour natural gas has to be sweetened by removing acid gases (carbon dioxide and/or hydrogen sulfide) before liquefaction. The solidification of these acid gases could be the basis for their separation from natural gas. In this study, a state-of-the art solid-vapor (SV) separation unit is developed for removal of acid gases from methane and simulated using a customized Aspen Plus operation unit. The operating principles and conditions, mathematical model, and performance results are presented for the SV unit. Further performance analyses, means of optimization and comparisons to conventional methods used by the industry were studied. Results showed that for similar sweet gas purity, the developed SV unit consumes only 27% of the energy required by the amine sweetening unit. Furthermore, it saves on capital costs, as it requires less equipment and does not suffer from high levels of corrosion.


  • Open Access

    A review on the solid–liquid–vapor phase equilibria of acid gases in methane

    by Hani Ababneh, Shaheen A. Al‐Muhtaseb

    In spite of the increasing levels of greenhouse gases in the atmosphere, and their impact on the environment, the demand for natural/biogas will increase significantly in the coming few decades. To cover this demand, the global energy industry is continuously exploiting sour gas reserves located around the world. Nonetheless, sour gas has to be sweetened before the practical utilization of natural or biogas. The cryogenic separation technologies have emerged as a new technology to separate carbon dioxide (CO2) and hydrogen sulfide (H2S gases) from natural/biogas. The cryogenic separation produces less harmful gases, and can be less expensive to operate and maintain in comparison to the conventional technologies. To design cryogenic separation equipment, vapor–liquid equilibrium (VLE), solid–liquid equilibrium (SLE), solid–vapor equilibrium (SVE), and solid–liquid–vapor equilibrium (SLVE) data for the corresponding binary systems (of CH4‐CO2, CH4‐H2S, and H2S‐CO2) and ternary system (of CH4‐H2S‐CO2) are required. The main target of this article is to review the SLVE data for the acid gases (CO2 and H2S) in methane (CH4) as the main constituent of natural/biogas. It will address SLVE data for the binary systems of CH4‐CO2, CH4‐H2S and H2S‐CO2 as well as the ternary system of CH4‐H2S‐CO2. It will not only address the available laboratory data, but it will also discuss, compare and evaluate the different models used to correlate/predict these data. © 2022 Society of Chemical Industry and John Wiley & Sons, Ltd.