Dominik Lausch
Research Subjects
Dominik Lausch has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Christian Hagendorf
Fraunhofer Center for Silicon‐Photovoltaics CSP 06120 Halle (Saale) Germany
12 shared publications Kai Petter
Q-Cells SE
6 shared publicationsVolker Naumann
Fraunhofer Center for Silicon Photovoltaics CSP 3 , 06120 Halle (Saale), Germany
6 shared publicationsK. Petter
Hanwha Q CELLS GmbH 3 , OT Thalheim, Sonnenallee 17–21, 06766 Bitterfeld-Wolfen, Germany
5 shared publicationsRonny Bakowskie
Q-Cells SE
5 shared publicationsJan Bauer
Max Planck Institute of Microstructure Physics, Halle, Germany
4 shared publications
Latest Publications
- 9 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 11 (6) , 1363-1369
Understanding Light- and Elevated Temperature-Induced Degradation in Silicon Wafers Using Hydrogen Effusion Mass Spectroscopy
Hydrogen has been long known for its ability to passivate defects in silicon devices. However, multiple recent studies on understanding the mechanism behind light- and elevated temperature-induced degradation (LeTID) have proposed that hydrogen plays an important role in this degradation mechanism. Despite its important role in photovoltaic applications, the quantitative assessment of hydrogen is difficult and seldom reported. In this work, we applied hydrogen effusion mass spectroscopy to quantify the hydrogen released from hydrogenated silicon nitride (SiN x :H) and atomic layer deposited (ALD) aluminum oxide (AlO x ) dielectric films at elevated temperatures. We demonstrate that the amount of hydrogen effused from these layers strongly correlates with the extent of LeTID observed in the multicrystalline silicon wafers passivated with these monolayers and their stacks. It is shown that the hydrogen effusion scales linearly with the SiN x :H thickness, similar as the extent of LeTID. The effusion measurements on the AlO x /SiN x :H stack revealed that the presence of the AlO x film modifies the total amount of hydrogen that is effused, whereas it was found to slow the hydrogen in-diffusion. This result is consistent with the LeTID extent determined after contact firing where ALD AlO x layers were found to act as a hydrogen diffusion barrier, strongly reducing LeTID when placed in between c-Si and SiN x :H and increasing LeTID when placed on top of SiN x :H.
- 9 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 11 (6) , 1363-1369
Understanding Light- and Elevated Temperature-Induced Degradation in Silicon Wafers Using Hydrogen Effusion Mass Spectroscopy
Hydrogen has been long known for its ability to passivate defects in silicon devices. However, multiple recent studies on understanding the mechanism behind light- and elevated temperature-induced degradation (LeTID) have proposed that hydrogen plays an important role in this degradation mechanism. Despite its important role in photovoltaic applications, the quantitative assessment of hydrogen is difficult and seldom reported. In this work, we applied hydrogen effusion mass spectroscopy to quantify the hydrogen released from hydrogenated silicon nitride (SiN x :H) and atomic layer deposited (ALD) aluminum oxide (AlO x ) dielectric films at elevated temperatures. We demonstrate that the amount of hydrogen effused from these layers strongly correlates with the extent of LeTID observed in the multicrystalline silicon wafers passivated with these monolayers and their stacks. It is shown that the hydrogen effusion scales linearly with the SiN x :H thickness, similar as the extent of LeTID. The effusion measurements on the AlO x /SiN x :H stack revealed that the presence of the AlO x film modifies the total amount of hydrogen that is effused, whereas it was found to slow the hydrogen in-diffusion. This result is consistent with the LeTID extent determined after contact firing where ALD AlO x layers were found to act as a hydrogen diffusion barrier, strongly reducing LeTID when placed in between c-Si and SiN x :H and increasing LeTID when placed on top of SiN x :H.
- Open Access
- 11 October 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 122 (14)
Low surface damage dry etched black silicon
Black silicon (bSi) is promising for integration into silicon solar cell fabrication flow due to its excellent light trapping and low reflectance, and a continuously improving passivation. However, intensive ion bombardment during the reactive ion etching used to fabricate bSi induces surface damage that causes significant recombination. Here, we present a process optimization strategy for bSi, where surface damage is reduced and surface passivation is improved while excellent light trapping and low reflectance are maintained. We demonstrate that reduction of the capacitively coupled plasma power, during reactive ion etching at non-cryogenic temperature (−20 °C), preserves the reflectivity below 1% and improves the effective minority carrier lifetime due to reduced ion energy. We investigate the effect of the etching process on the surface morphology, light trapping, reflectance, transmittance, and effective lifetime of bSi. Additional surface passivation using atomic layer deposition of Al2O3 significantly improves the effective lifetime. For n-type wafers, the lifetime reaches 12 ms for polished and 7.5 ms for bSi surfaces. For p-type wafers, the lifetime reaches 800 μs for both polished and bSi surfaces.
- 11 October 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 122 (14)
Open AccessLow surface damage dry etched black silicon
Black silicon (bSi) is promising for integration into silicon solar cell fabrication flow due to its excellent light trapping and low reflectance, and a continuously improving passivation. However, intensive ion bombardment during the reactive ion etching used to fabricate bSi induces surface damage that causes significant recombination. Here, we present a process optimization strategy for bSi, where surface damage is reduced and surface passivation is improved while excellent light trapping and low reflectance are maintained. We demonstrate that reduction of the capacitively coupled plasma power, during reactive ion etching at non-cryogenic temperature (−20 °C), preserves the reflectivity below 1% and improves the effective minority carrier lifetime due to reduced ion energy. We investigate the effect of the etching process on the surface morphology, light trapping, reflectance, transmittance, and effective lifetime of bSi. Additional surface passivation using atomic layer deposition of Al2O3 significantly improves the effective lifetime. For n-type wafers, the lifetime reaches 12 ms for polished and 7.5 ms for bSi surfaces. For p-type wafers, the lifetime reaches 800 μs for both polished and bSi surfaces.
- 9 February 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 121 (6)
Elemental evolution of the SiOxFy self-masking layer of plasma textured silicon and its modification during air exposure
The influence of the SiOxFy selfmasking process on the formation of black-Silicon (b-Si) textures by maskless SF6/O2 plasma etching is of great interest with regard to the optimization of the texturing process for highly antireflective silicon. For that reason, the elemental composition of plasma textured silicon surfaces is analyzed by transmission electron microscopy and X-ray photoelectron spectroscopy. The chemical composition of a fluorine containing oxide layer on top of the surface was confirmed and determined quantitatively. A strongly reduced F content was found after ambient air exposure. A qualitative model of the chemical and physical processes caused by maskless plasma texturing was developed to explain the observed experimental results. The decrease in the F content is assumed to be caused by hydrolysis of F by air moisture, resulting in a successive desorption of HF and transformation of SiOxFy to silicon oxide.
- 9 February 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 121 (6)
Elemental evolution of the SiOxFy self-masking layer of plasma textured silicon and its modification during air exposure
The influence of the SiOxFy selfmasking process on the formation of black-Silicon (b-Si) textures by maskless SF6/O2 plasma etching is of great interest with regard to the optimization of the texturing process for highly antireflective silicon. For that reason, the elemental composition of plasma textured silicon surfaces is analyzed by transmission electron microscopy and X-ray photoelectron spectroscopy. The chemical composition of a fluorine containing oxide layer on top of the surface was confirmed and determined quantitatively. A strongly reduced F content was found after ambient air exposure. A qualitative model of the chemical and physical processes caused by maskless plasma texturing was developed to explain the observed experimental results. The decrease in the F content is assumed to be caused by hydrolysis of F by air moisture, resulting in a successive desorption of HF and transformation of SiOxFy to silicon oxide.
- Open Access
- 3 December 2016
- Published by IM Publications Open LLP in Journal of Spectral Imaging
- Vol. 5
Hyperspectral photoluminescence imaging of defects in solar cells
The present work is a demonstration of how near infrared (NIR) hyperspectral photoluminescence imaging can be used to detect defects in silicon wafers and solar cells. Chemometric analysis techniques such as multivariate curve resolution (MCR) and partial least squares discriminant analysis (PLS-DA) allow various types of defects to be classified and cascades of radiative defects in the samples to be extracted. It is also demonstrated how utilising a macro lens yields a spatial resolution of 30 µm on selected regions of the samples, revealing that some types of defect signals originate in grain boundaries of the silicon crystal, whereas other signals show up as singular spots. Combined with independent investigation techniques, hyperspectral imaging is a promising tool for determining origins of defects in silicon samples for photovoltaic applications.
- 3 December 2016
- Published by IM Publications Open LLP in Journal of Spectral Imaging
- Vol. 5
Open AccessHyperspectral photoluminescence imaging of defects in solar cells
The present work is a demonstration of how near infrared (NIR) hyperspectral photoluminescence imaging can be used to detect defects in silicon wafers and solar cells. Chemometric analysis techniques such as multivariate curve resolution (MCR) and partial least squares discriminant analysis (PLS-DA) allow various types of defects to be classified and cascades of radiative defects in the samples to be extracted. It is also demonstrated how utilising a macro lens yields a spatial resolution of 30 µm on selected regions of the samples, revealing that some types of defect signals originate in grain boundaries of the silicon crystal, whereas other signals show up as singular spots. Combined with independent investigation techniques, hyperspectral imaging is a promising tool for determining origins of defects in silicon samples for photovoltaic applications.
- 3 February 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 119 (5) , 054501
Classification of crystal defects in multicrystalline silicon solar cells and wafer using spectrally and spatially resolved photoluminescence
In this contribution, spectral photoluminescence (SPL) imaging detecting both the spectral distribution and the lateral position is applied on recombination active defects in multicrystalline silicon solar cells and wafers. The result is analysed by a Multivariate Curve Resolution (MCR) algorithm using the spectral photoluminescence response and their positions. (i) Without any pre-assumptions made, the algorithm distinguishes four different recombination active defect types. Looking at the spatial distribution, it is shown that two of these defect types coincide with two defect types that have been distinguished on solar cell level using an analysis of forward and reverse biased electroluminescence (denoted as Type-A and -B) previously. (ii) Using SPL, all previously classified defects can also be distinguished at the wafer level. Therefore, the defects limiting the solar cell efficiency are already present in the wafer material and not introduced by the solar cell process. This is of particular interest for the question of how to predict the solar cell efficiency based on the PL measurements at the wafer level. The SPL is able to distinguish between the recombination activity of the dominant Type-A and -B defects that cannot be distinguished by classical PL measurements of the band-to-band recombination at the wafer level. The technique also highlights the changes in recombination activity of the given defects throughout the fabrication process. (iii) Additionally, it is shown that the spectral peak positions of Type-A defects coincide with the known D3 and D4 lines and of Type-B defects with the D1 line on both solar cell and wafer level. Two further defects are captured by the MCR algorithm denoted as Type-VID3 and Type-D07 defects occurring as spot-like defects in isolated positions. Their spectral PL response is analysed as well.
- 3 February 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 119 (5) , 054501
Classification of crystal defects in multicrystalline silicon solar cells and wafer using spectrally and spatially resolved photoluminescence
In this contribution, spectral photoluminescence (SPL) imaging detecting both the spectral distribution and the lateral position is applied on recombination active defects in multicrystalline silicon solar cells and wafers. The result is analysed by a Multivariate Curve Resolution (MCR) algorithm using the spectral photoluminescence response and their positions. (i) Without any pre-assumptions made, the algorithm distinguishes four different recombination active defect types. Looking at the spatial distribution, it is shown that two of these defect types coincide with two defect types that have been distinguished on solar cell level using an analysis of forward and reverse biased electroluminescence (denoted as Type-A and -B) previously. (ii) Using SPL, all previously classified defects can also be distinguished at the wafer level. Therefore, the defects limiting the solar cell efficiency are already present in the wafer material and not introduced by the solar cell process. This is of particular interest for the question of how to predict the solar cell efficiency based on the PL measurements at the wafer level. The SPL is able to distinguish between the recombination activity of the dominant Type-A and -B defects that cannot be distinguished by classical PL measurements of the band-to-band recombination at the wafer level. The technique also highlights the changes in recombination activity of the given defects throughout the fabrication process. (iii) Additionally, it is shown that the spectral peak positions of Type-A defects coincide with the known D3 and D4 lines and of Type-B defects with the D1 line on both solar cell and wafer level. Two further defects are captured by the MCR algorithm denoted as Type-VID3 and Type-D07 defects occurring as spot-like defects in isolated positions. Their spectral PL response is analysed as well.
- Open Access
- 8 March 2015
- Published by Wiley in Journal of Solar Energy
- Vol. 2015, 1-9
Influence of Different Types of Recombination Active Defects on the Integral Electrical Properties of Multicrystalline Silicon Solar Cells
In this contribution the influence of different types of recombination-active defects on the integral electrical properties of multicrystalline Si solar cells is investigated. Based on a previous classification scheme related to the luminescence behavior of crystal defects, Type-A and Type-B defects are locally distinguished. It is shown that Type-A defects, correlated to iron contaminations, are dominating the efficiency by more than 20% relative through their impact on the short circuit currentISCand open circuit voltageVOCin standard Si material (only limited by recombination active crystal defects). Contrarily, Type-B defects show low influence on the efficiency of 3% relative. The impact of the detrimental Type-A defects on the electrical parameters is studied as a function of the block height. A clear correlation between the area fraction of Type-A defects and both the global Isc and the prebreakdown behavior (reverse current) in voltage regime-2 (−11 V) is observed. An outlier having an increased full-area recombination activity is traced back to dense inter- and intragrain nucleation of Fe precipitates. Based on these results it is concluded that Type-A defects are the most detrimental defects in Si solar cells (having efficiencies > 15%) and have to be prevented by optimized Si material quality and solar cell process conditions.
- 8 March 2015
- Published by Wiley in Journal of Solar Energy
- Vol. 2015, 1-9
Open AccessInfluence of Different Types of Recombination Active Defects on the Integral Electrical Properties of Multicrystalline Silicon Solar Cells
In this contribution the influence of different types of recombination-active defects on the integral electrical properties of multicrystalline Si solar cells is investigated. Based on a previous classification scheme related to the luminescence behavior of crystal defects, Type-A and Type-B defects are locally distinguished. It is shown that Type-A defects, correlated to iron contaminations, are dominating the efficiency by more than 20% relative through their impact on the short circuit currentISCand open circuit voltageVOCin standard Si material (only limited by recombination active crystal defects). Contrarily, Type-B defects show low influence on the efficiency of 3% relative. The impact of the detrimental Type-A defects on the electrical parameters is studied as a function of the block height. A clear correlation between the area fraction of Type-A defects and both the global Isc and the prebreakdown behavior (reverse current) in voltage regime-2 (−11 V) is observed. An outlier having an increased full-area recombination activity is traced back to dense inter- and intragrain nucleation of Fe precipitates. Based on these results it is concluded that Type-A defects are the most detrimental defects in Si solar cells (having efficiencies > 15%) and have to be prevented by optimized Si material quality and solar cell process conditions.
- Top Cited Papers
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 4 (3) , 834-840
Potential-Induced Degradation (PID): Introduction of a Novel Test Approach and Explanation of Increased Depletion Region Recombination
In recent years, a detrimental degradation mechanism of solar cells in large photovoltaic fields called potential-induced degradation (PID) has been intensively investigated and discussed. Here, the module efficiency is decreasing down to a fractional part of their original efficiency. In this study, we introduce a PID test at a solar-cell level and for individual module components applicable as a tool for process control in industries and root cause analyses in science departments. Using the proposed method, one example analysis of a solar cell that is degraded by the PID tester is presented. It is shown that PID of the shunting type influences both the parallel resistance (Rp) and the depletion region recombination behavior (J02) of the solar cell. Increased recombination in the depletion region is caused by Na decorated stacking faults crossing the depletion region. This strongly influences recombination behavior in the depletion region, leading to an increased J02 and an ideality factor n2 > 2. However, the defects leave the base of the solar cell primarily unaffected, and hence, J 01 recombination remains rather low. Based on these findings, a model for the shunting and the increased depletion region recombination behavior is discussed.
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 4 (3) , 834-840
Top Cited PapersPotential-Induced Degradation (PID): Introduction of a Novel Test Approach and Explanation of Increased Depletion Region Recombination
In recent years, a detrimental degradation mechanism of solar cells in large photovoltaic fields called potential-induced degradation (PID) has been intensively investigated and discussed. Here, the module efficiency is decreasing down to a fractional part of their original efficiency. In this study, we introduce a PID test at a solar-cell level and for individual module components applicable as a tool for process control in industries and root cause analyses in science departments. Using the proposed method, one example analysis of a solar cell that is degraded by the PID tester is presented. It is shown that PID of the shunting type influences both the parallel resistance (Rp) and the depletion region recombination behavior (J02) of the solar cell. Increased recombination in the depletion region is caused by Na decorated stacking faults crossing the depletion region. This strongly influences recombination behavior in the depletion region, leading to an increased J02 and an ideality factor n2 > 2. However, the defects leave the base of the solar cell primarily unaffected, and hence, J 01 recombination remains rather low. Based on these findings, a model for the shunting and the increased depletion region recombination behavior is discussed.
- Open Access
- 1 January 2014
- Published by Elsevier in Energy Procedia
- Vol. 55, 486-493
Sodium Outdiffusion from Stacking Faults as Root Cause for the Recovery Process of Potential-induced Degradation (PID)
- 1 January 2014
- Published by Elsevier in Energy Procedia
- Vol. 55, 486-493
Open AccessSodium Outdiffusion from Stacking Faults as Root Cause for the Recovery Process of Potential-induced Degradation (PID)
- Top Cited Papers
- 1 January 2014
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 120, 383-389
Explanation of potential-induced degradation of the shunting type by Na decoration of stacking faults in Si solar cells
- 1 January 2014
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 120, 383-389
Top Cited PapersExplanation of potential-induced degradation of the shunting type by Na decoration of stacking faults in Si solar cells
- 21 November 2013
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 114 (19) , 194509
Determination of crystal grain orientations by optical microscopy at textured surfaces
In this contribution, a new method to determine the crystal orientation with the example of chemical treated silicon wafers by means of optical microscopy has been demonstrated. The introduced procedure represents an easy method to obtain all relevant parameters to describe the crystal structure of the investigated material, i.e., the crystal grain orientation and the grain boundary character. The chemical treatment is a standard mono-texture for solar cells, well known in the solar industry. In general, this concept can also be applied to other crystalline materials, i.e., GaAs, SiC, etc., the only thing that needs to be adjusted is the texturing method to reveal specific crystal planes and the calculation model. In conclusion, an application of this method is shown with the example of the defect classification of recombination active defects in mc-Si solar cell. The introduced method demonstrates a simple and quick opportunity to improve the crystallization process and the quality of electronic devices by means of an optical microscope and a chemical treatment of the material.
- 21 November 2013
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 114 (19) , 194509
Determination of crystal grain orientations by optical microscopy at textured surfaces
In this contribution, a new method to determine the crystal orientation with the example of chemical treated silicon wafers by means of optical microscopy has been demonstrated. The introduced procedure represents an easy method to obtain all relevant parameters to describe the crystal structure of the investigated material, i.e., the crystal grain orientation and the grain boundary character. The chemical treatment is a standard mono-texture for solar cells, well known in the solar industry. In general, this concept can also be applied to other crystalline materials, i.e., GaAs, SiC, etc., the only thing that needs to be adjusted is the texturing method to reveal specific crystal planes and the calculation model. In conclusion, an application of this method is shown with the example of the defect classification of recombination active defects in mc-Si solar cell. The introduced method demonstrates a simple and quick opportunity to improve the crystallization process and the quality of electronic devices by means of an optical microscope and a chemical treatment of the material.