Kyeong-Keun Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kyeong-Keun Choi has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Deok-Kee Kim
Sejong University
5 shared publications Sung-Kyu Kim
4 shared publicationsYoun-Jang Kim
4 shared publicationsChan-Gyung Park
3 shared publicationsJong Kee
3 shared publications- Rock-Hyun Baek
Pohang University of Science and Technology (POSTECH)
3 shared publications
Latest Publications
- 1 February 2025
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 14 (2) , 023012
Impact of ALD Al2O3 Dielectrics on the Device Performance of SiC-Based Field-Effect Transistors (FETs): A Study of Atomic Diffusion
We investigated double-diffused (D)-MOSFETs based on 4H-SiC with an atomic-layer-deposited (ALD) 30 nm-thick Al2O3/15 nm-thick SiO2 bi-layer to improve the microstructure and electrical properties, particularly the subthreshold swing (S) and atomic diffusion behavior of phosphorus (P) in the P-doped poly-Si gates. Stacking the 30 nm-thick ALD Al2O3 on the SiO2 layer reduced the subthreshold swing (S) of the bi-layer film (Al2O3/SiO2) by approximately 53% compared to that of the SiO2 single dielectric film, demonstrating a reduction from 732.3 to 345.7 (mV/decade) at room measuring temperature of about 25 °C. The device performance of gate improved by Al2O3 dielectrics blocking of the atomic diffusions of phosphorus (P) and carbon (C). This effect was analyzed in more detail using atom probe tomography (APT). The penetration depth of P atoms in bilayer of Al2O3/SiO2 was about 8.4 nm less than that in the single layer of SiO2, owing to the blocking of the P atomic diffusion by the ALD Al2O3 film.
- 1 February 2025
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 14 (2) , 023012
Impact of ALD Al2O3 Dielectrics on the Device Performance of SiC-Based Field-Effect Transistors (FETs): A Study of Atomic Diffusion
We investigated double-diffused (D)-MOSFETs based on 4H-SiC with an atomic-layer-deposited (ALD) 30 nm-thick Al2O3/15 nm-thick SiO2 bi-layer to improve the microstructure and electrical properties, particularly the subthreshold swing (S) and atomic diffusion behavior of phosphorus (P) in the P-doped poly-Si gates. Stacking the 30 nm-thick ALD Al2O3 on the SiO2 layer reduced the subthreshold swing (S) of the bi-layer film (Al2O3/SiO2) by approximately 53% compared to that of the SiO2 single dielectric film, demonstrating a reduction from 732.3 to 345.7 (mV/decade) at room measuring temperature of about 25 °C. The device performance of gate improved by Al2O3 dielectrics blocking of the atomic diffusions of phosphorus (P) and carbon (C). This effect was analyzed in more detail using atom probe tomography (APT). The penetration depth of P atoms in bilayer of Al2O3/SiO2 was about 8.4 nm less than that in the single layer of SiO2, owing to the blocking of the P atomic diffusion by the ALD Al2O3 film.
- 26 July 2024
- Published by Elsevier in Current Applied Physics
- Vol. 67, 69-74
Enhancing the thermal stability of active contacts in AlGaN/GaN high electron mobility transistors with chemical vapor deposited carbon (C) films
- 26 July 2024
- Published by Elsevier in Current Applied Physics
- Vol. 67, 69-74
Enhancing the thermal stability of active contacts in AlGaN/GaN high electron mobility transistors with chemical vapor deposited carbon (C) films
- 2 February 2024
- Published by IOP Publishing in Nanotechnology
- Vol. 35 (16) , 165204
In-situ temperature-dependent sheet resistance study of Cu films in oxygen ambient for heterogeneous integrations
Controlling and preventing Cu oxidation is crucial for improving the performance and reliability of Cu–Cu bonding. Ni-B films were selectively deposited on Cu films to block the Cu oxidation. The resistivity changes of the Cu films in N2 and O2 ambient were measured by using a four-point probe in the in situ temperature-dependent resistance measurements at the temperature from room temperature to 400 °C. The resistivity changes of the 100 nm thick Cu films without Ni-B increased rapidly at a higher temperature (284 °C) in the O2 ambiance. The change of resistivity-increase of 100 nm thick Cu with ∼50 nm thick Ni-B (top) film was lower than the Cu films without Ni-B films due to the blocking diffusion of O2 atoms by the Ni-B films. The resistivity-change and oxidation barrier properties were studied using scanning electron microscopy, FIB, transmission electron microscopy, EDX, and secondary ion mass spectroscopy tools. The proposed article will be helpful for the upcoming advancement in Cu–Cu bonding using selected-area deposition.
- 2 February 2024
- Published by IOP Publishing in Nanotechnology
- Vol. 35 (16) , 165204
In-situ temperature-dependent sheet resistance study of Cu films in oxygen ambient for heterogeneous integrations
Controlling and preventing Cu oxidation is crucial for improving the performance and reliability of Cu–Cu bonding. Ni-B films were selectively deposited on Cu films to block the Cu oxidation. The resistivity changes of the Cu films in N2 and O2 ambient were measured by using a four-point probe in the in situ temperature-dependent resistance measurements at the temperature from room temperature to 400 °C. The resistivity changes of the 100 nm thick Cu films without Ni-B increased rapidly at a higher temperature (284 °C) in the O2 ambiance. The change of resistivity-increase of 100 nm thick Cu with ∼50 nm thick Ni-B (top) film was lower than the Cu films without Ni-B films due to the blocking diffusion of O2 atoms by the Ni-B films. The resistivity-change and oxidation barrier properties were studied using scanning electron microscopy, FIB, transmission electron microscopy, EDX, and secondary ion mass spectroscopy tools. The proposed article will be helpful for the upcoming advancement in Cu–Cu bonding using selected-area deposition.
- Open Access
- 26 September 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (19) , 2642
Thermal, Mechanical, and Electrical Stability of Cu Films in an Integration Process with Photosensitive Polyimide (PSPI) Films
Photosensitive polyimides (PSPIs) have been widely developed in microelectronics, which is due to their excellent thermal properties and reasonable dielectric properties and can be directly patterned to simplify the processing steps. In this study, 3 μm~7 μm thick PSPI films were deposited on different substrates, including Si, 50 nm SiN, 50 nm SiO2, 100 nm Cu, and 100 nm Al, for the optimization of the process of integration with Cu films. In situ temperature-dependent resistance measurements were conducted by using a four-point probe system to study the changes in resistance of the 70 nm thick Cu films on different dielectrics with thick diffusion films of 30 nm Mn, Co, and W films in a N2 ambient. The lowest possible change in thickness due to annealing at the higher temperature ranges of 325 °C to 375 °C is displayed, which suggests the high stability of PSPI. The PSPI films show good adhesion with each Cu diffusion barrier up to 350 °C, and we believe that this will be helpful for new packaging applications, such as a 3D IC with a Cu interconnect.
- 26 September 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (19) , 2642
Open AccessThermal, Mechanical, and Electrical Stability of Cu Films in an Integration Process with Photosensitive Polyimide (PSPI) Films
Photosensitive polyimides (PSPIs) have been widely developed in microelectronics, which is due to their excellent thermal properties and reasonable dielectric properties and can be directly patterned to simplify the processing steps. In this study, 3 μm~7 μm thick PSPI films were deposited on different substrates, including Si, 50 nm SiN, 50 nm SiO2, 100 nm Cu, and 100 nm Al, for the optimization of the process of integration with Cu films. In situ temperature-dependent resistance measurements were conducted by using a four-point probe system to study the changes in resistance of the 70 nm thick Cu films on different dielectrics with thick diffusion films of 30 nm Mn, Co, and W films in a N2 ambient. The lowest possible change in thickness due to annealing at the higher temperature ranges of 325 °C to 375 °C is displayed, which suggests the high stability of PSPI. The PSPI films show good adhesion with each Cu diffusion barrier up to 350 °C, and we believe that this will be helpful for new packaging applications, such as a 3D IC with a Cu interconnect.
- Open Access
- 16 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 60660-60667
Curing Process on Passivation Layer for Backside-Illuminated CMOS Image Sensor Application
We fabricated Al/Al 2 O 3 /SiO 2 /Si and Al/HfO 2 /Si structures to optimize the passivation layer of a backside-illuminated (BSI) complementary metal oxide semiconductor (CMOS) image sensor (CIS), with the key properties of the newly developed high- k passivation layer analyzed via border traps, interface traps, and fixed charges. In the first experiment using Al 2 O 3 /SiO 2 bilayer-based structures, different thicknesses of SiO 2 were applied from 0 to 15 nm. The improvement in their properties was confirmed by applying forming gas annealing (FGA), a type of post-treatment, to all experimental systems. The first experiment results indicated that both the SiO 2 layer and FGA were effective for chemical passivation. However, a tradeoff occurred in the degree of improvement of the interface trap density (D it ) and fixed-charge density (Q f ) according to the SiO 2 layer thickness. Subsequently, in the second experiment using HfO 2 single-layer-based structures, FGA improved the border trap to a relatively poor extent compared to the first experiment. Nevertheless, FGA improved the electrical characteristics of the HfO 2 films without any side effects and results in optimal D it and |Q f /q| values of 2.59×10 11 eV -1 cm -2 and 1.00×10 12 cm -2 , respectively, demonstrating its potential for the passivation layer in BSI CIS applications.
- 16 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 60660-60667
Open AccessCuring Process on Passivation Layer for Backside-Illuminated CMOS Image Sensor Application
We fabricated Al/Al 2 O 3 /SiO 2 /Si and Al/HfO 2 /Si structures to optimize the passivation layer of a backside-illuminated (BSI) complementary metal oxide semiconductor (CMOS) image sensor (CIS), with the key properties of the newly developed high- k passivation layer analyzed via border traps, interface traps, and fixed charges. In the first experiment using Al 2 O 3 /SiO 2 bilayer-based structures, different thicknesses of SiO 2 were applied from 0 to 15 nm. The improvement in their properties was confirmed by applying forming gas annealing (FGA), a type of post-treatment, to all experimental systems. The first experiment results indicated that both the SiO 2 layer and FGA were effective for chemical passivation. However, a tradeoff occurred in the degree of improvement of the interface trap density (D it ) and fixed-charge density (Q f ) according to the SiO 2 layer thickness. Subsequently, in the second experiment using HfO 2 single-layer-based structures, FGA improved the border trap to a relatively poor extent compared to the first experiment. Nevertheless, FGA improved the electrical characteristics of the HfO 2 films without any side effects and results in optimal D it and |Q f /q| values of 2.59×10 11 eV -1 cm -2 and 1.00×10 12 cm -2 , respectively, demonstrating its potential for the passivation layer in BSI CIS applications.
- Open Access
- 14 February 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (4) , 731
H2 Plasma and PMA Effects on PEALD-Al2O3 Films with Different O2 Plasma Exposure Times for CIS Passivation Layers
In this study, the electrical properties of Al2O3 film were analyzed and optimized to improve the properties of the passivation layer of CMOS image sensors (CISs). During Al2O3 deposition processing, the O2 plasma exposure time was adjusted, and H2 plasma treatment as well as post-metallization annealing (PMA) were performed as posttreatments. The flat-band voltage (Vfb) was significantly shifted (ΔVfb = 2.54 V) in the case of the Al2O3 film with a shorter O2 plasma exposure time; however, with a longer O2 plasma exposure time, Vfb was slightly shifted (ΔVfb = 0.61 V) owing to the reduction in the carbon impurity content. Additionally, the as-deposited Al2O3 sample with a shorter O2 plasma exposure time had a larger number of interface traps (interface trap density, Dit = 8.98 × 1013 eV−1·cm−2). However, Dit was reduced to 1.12 × 1012 eV−1·cm−2 by increasing the O2 plasma exposure time and further reduced after PMA. Consequently, we fabricated an Al2O3 film suitable for application as a CIS passivation layer with a reduced number of interface traps. However, the Al2O3 film with increased O2 plasma exposure time deteriorated owing to plasma damage after H2 plasma treatment, which is a method of reducing carbon impurity content. This deterioration was validated using the C–V hump and breakdown characteristics.
- 14 February 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (4) , 731
Open AccessH2 Plasma and PMA Effects on PEALD-Al2O3 Films with Different O2 Plasma Exposure Times for CIS Passivation Layers
In this study, the electrical properties of Al2O3 film were analyzed and optimized to improve the properties of the passivation layer of CMOS image sensors (CISs). During Al2O3 deposition processing, the O2 plasma exposure time was adjusted, and H2 plasma treatment as well as post-metallization annealing (PMA) were performed as posttreatments. The flat-band voltage (Vfb) was significantly shifted (ΔVfb = 2.54 V) in the case of the Al2O3 film with a shorter O2 plasma exposure time; however, with a longer O2 plasma exposure time, Vfb was slightly shifted (ΔVfb = 0.61 V) owing to the reduction in the carbon impurity content. Additionally, the as-deposited Al2O3 sample with a shorter O2 plasma exposure time had a larger number of interface traps (interface trap density, Dit = 8.98 × 1013 eV−1·cm−2). However, Dit was reduced to 1.12 × 1012 eV−1·cm−2 by increasing the O2 plasma exposure time and further reduced after PMA. Consequently, we fabricated an Al2O3 film suitable for application as a CIS passivation layer with a reduced number of interface traps. However, the Al2O3 film with increased O2 plasma exposure time deteriorated owing to plasma damage after H2 plasma treatment, which is a method of reducing carbon impurity content. This deterioration was validated using the C–V hump and breakdown characteristics.
- Open Access
- 16 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 68724-68730
Effect of ALD Processes on Physical and Electrical Properties of HfO2 Dielectrics for the Surface Passivation of a CMOS Image Sensor Application
The surface passivation of a CMOS image sensor (CIS) is highly beneficial for the overall improvement of a device performance. We employed the thermal atomic layer deposition (T-ALD) and plasma enhanced (PE-ALD) techniques for the deposition of 20 nm HfO 2 as well as stacked with 3 and 5 nm Al 2 O 3 thin films. The HfO 2 /Si and Al 2 O 3 /HfO 2 /Si metal-oxide-semiconductor structures were used to analyze the fixed charge density ( $\text{Q}_{\mathrm {f}}$ ) and interface trap density ( $\text{D}_{\mathrm {it}}$ ). The as-synthesized samples show high $\text{D}_{\mathrm {it}}$ and $\text{Q}_{\mathrm {f}}$ values (10 12 cm −2 eV −1 ) and a minority carrier lifetime of 15–300 $\mu \text{s}$ . The finite-difference time-domain simulation of high-k dielectrics confirmed that the Al 2 O 3 (top)/HfO 2 stacked structures expected higher quantum efficiency for CIS application. The effect of vacuum annealing (VA) and forming gas annealing (FGA) treatments succeeded with the decomposition of the $\text{D}_{\mathrm {it}}$ and increase in carrier lifetime. The H 2 ambient FGA samples showed a remarkable decrease in the $\text{D}_{\mathrm {it}}$ values. To improve the overall performance of the device after passivation, we employed an Al 2 O 3 /HfO 2 bilayer structure, which showed a low $\text{D}_{\mathrm {it}}$ of 10 11 cm −2 eV −1 and a minority carrier lifetime of $\sim 3$ ,700 $\mu \text{s}$ after 400 °C and 30 min FGA. We believe that this surface passivation strategy will pave way for future CIS technology regarding the development of lower defective surface and superior performance.
- 16 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 68724-68730
Open AccessEffect of ALD Processes on Physical and Electrical Properties of HfO2 Dielectrics for the Surface Passivation of a CMOS Image Sensor Application
The surface passivation of a CMOS image sensor (CIS) is highly beneficial for the overall improvement of a device performance. We employed the thermal atomic layer deposition (T-ALD) and plasma enhanced (PE-ALD) techniques for the deposition of 20 nm HfO 2 as well as stacked with 3 and 5 nm Al 2 O 3 thin films. The HfO 2 /Si and Al 2 O 3 /HfO 2 /Si metal-oxide-semiconductor structures were used to analyze the fixed charge density ( $\text{Q}_{\mathrm {f}}$ ) and interface trap density ( $\text{D}_{\mathrm {it}}$ ). The as-synthesized samples show high $\text{D}_{\mathrm {it}}$ and $\text{Q}_{\mathrm {f}}$ values (10 12 cm −2 eV −1 ) and a minority carrier lifetime of 15–300 $\mu \text{s}$ . The finite-difference time-domain simulation of high-k dielectrics confirmed that the Al 2 O 3 (top)/HfO 2 stacked structures expected higher quantum efficiency for CIS application. The effect of vacuum annealing (VA) and forming gas annealing (FGA) treatments succeeded with the decomposition of the $\text{D}_{\mathrm {it}}$ and increase in carrier lifetime. The H 2 ambient FGA samples showed a remarkable decrease in the $\text{D}_{\mathrm {it}}$ values. To improve the overall performance of the device after passivation, we employed an Al 2 O 3 /HfO 2 bilayer structure, which showed a low $\text{D}_{\mathrm {it}}$ of 10 11 cm −2 eV −1 and a minority carrier lifetime of $\sim 3$ ,700 $\mu \text{s}$ after 400 °C and 30 min FGA. We believe that this surface passivation strategy will pave way for future CIS technology regarding the development of lower defective surface and superior performance.
- 20 March 2022
- Published by Elsevier in Microelectronic Engineering
- Vol. 258
Effect of hydrogen plasma treatment on the electrical properties for SiC-based power MOSFETs
- 20 March 2022
- Published by Elsevier in Microelectronic Engineering
- Vol. 258
Effect of hydrogen plasma treatment on the electrical properties for SiC-based power MOSFETs
- Open Access
Highly Fast Response of Pd/Ta2O5/SiC and Pd/Ta2O5/Si Schottky Diode-Based Hydrogen Sensors
Herein, the fabrication of a novel highly sensitive and fast hydrogen (H2) gas sensor, based on the Ta2O5 Schottky diode, is described. First, Ta2O5 thin films are deposited on silicon carbide (SiC) and silicon (Si) substrates via a radio frequency (RF) sputtering method. Then, Pd and Ni are respectively deposited on the front and back of the device. The deposited Pd serves as a H2 catalyst, while the Ni functions as an Ohmic contact. The devices are then tested under various concentrations of H2 gas at operating temperatures of 300, 500, and 700 °C. The results indicate that the Pd/Ta2O5 Schottky diode on the SiC substrate exhibits larger concentration and temperature sensitivities than those of the device based on the Si substrate. In addition, the optimum operating temperature of the Pd/Ta2O5 Schottky diode for use in H2 sensing is shown to be about 300 °C. At this optimum temperature, the dynamic responses of the sensors towards various concentrations of H2 gas are then examined under a constant bias current of 1 mA. The results indicate a fast rise time of 7.1 s, and a decay of 18 s, for the sensor based on the SiC substrate.
Open AccessHighly Fast Response of Pd/Ta2O5/SiC and Pd/Ta2O5/Si Schottky Diode-Based Hydrogen Sensors
Herein, the fabrication of a novel highly sensitive and fast hydrogen (H2) gas sensor, based on the Ta2O5 Schottky diode, is described. First, Ta2O5 thin films are deposited on silicon carbide (SiC) and silicon (Si) substrates via a radio frequency (RF) sputtering method. Then, Pd and Ni are respectively deposited on the front and back of the device. The deposited Pd serves as a H2 catalyst, while the Ni functions as an Ohmic contact. The devices are then tested under various concentrations of H2 gas at operating temperatures of 300, 500, and 700 °C. The results indicate that the Pd/Ta2O5 Schottky diode on the SiC substrate exhibits larger concentration and temperature sensitivities than those of the device based on the Si substrate. In addition, the optimum operating temperature of the Pd/Ta2O5 Schottky diode for use in H2 sensing is shown to be about 300 °C. At this optimum temperature, the dynamic responses of the sensors towards various concentrations of H2 gas are then examined under a constant bias current of 1 mA. The results indicate a fast rise time of 7.1 s, and a decay of 18 s, for the sensor based on the SiC substrate.