Cristina Gatta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Cristina Gatta has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Daniela Addessi
Department of Structural and Geotechnical Engineering, Sapienza University of Rome, Rome, Italy
13 shared publications - Paolo Di Re
Sapienza University of Rome
5 shared publications - Elio Sacco
Department of Structures for Engineering and Architecture, University of Naples Federico II, Naples, Italy
4 shared publications Daniela Addessi
3 shared publications- Domenico Liberatore
Sapienza University of Rome
2 shared publications - Elena Benvenuti
Department of Engineering, University of Ferrara, Ferrara, Italy
2 shared publications
Latest Publications
- 1 April 2026
- Published by Springer Nature
- p. 633-639
Effect of Randomly Distributed Imperfections on the Buckling Response of Soft Lattice Metamaterials
- 1 April 2026
- Published by Springer Nature
- p. 633-639
Effect of Randomly Distributed Imperfections on the Buckling Response of Soft Lattice Metamaterials
- Open Access
- 3 March 2026
- Published by Springer Nature
- p. 185-204
Enhanced Modeling Approaches to Introduce the Effects of Environmental and Mechanical Damage
This contribution focuses on modeling procedures to describe damage mechanisms evolving in masonry structures under mechanical and environmental actions. After introducing the proposed protocol developed to analyze the overall mechanical response of masonry historical constructions, a macromechanical constitutive model coupling damage and plasticity effects is presented in detail. Two case studies are analyzed, concerning a masonry façade subjected to tunneling-induced settlements and the Tortona town hall, selected as real cases to evaluate the effects of environmental and man-made loads on the structural response of buildings with historical relevance.
- 3 March 2026
- Published by Springer Nature
- p. 185-204
Open AccessEnhanced Modeling Approaches to Introduce the Effects of Environmental and Mechanical Damage
This contribution focuses on modeling procedures to describe damage mechanisms evolving in masonry structures under mechanical and environmental actions. After introducing the proposed protocol developed to analyze the overall mechanical response of masonry historical constructions, a macromechanical constitutive model coupling damage and plasticity effects is presented in detail. Two case studies are analyzed, concerning a masonry façade subjected to tunneling-induced settlements and the Tortona town hall, selected as real cases to evaluate the effects of environmental and man-made loads on the structural response of buildings with historical relevance.
- 23 June 2025
- Published by Springer Nature in Meccanica
- Vol. 60 (7) , 1917-1937
Buckling and post-buckling analysis of masonry walls using Virtual Elements and cohesive interfaces
- 23 June 2025
- Published by Springer Nature in Meccanica
- Vol. 60 (7) , 1917-1937
Buckling and post-buckling analysis of masonry walls using Virtual Elements and cohesive interfaces
- 25 May 2025
- Published by Springer Nature
- p. 141-152
Modeling of Fracture Propagation in Random Composites Coupling Virtual Elements and Interface Elements
- 25 May 2025
- Published by Springer Nature
- p. 141-152
Modeling of Fracture Propagation in Random Composites Coupling Virtual Elements and Interface Elements
- Open Access
- 28 September 2024
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 432
A coupled virtual element-interface model for analysis of fracture propagation in polycrystalline composites
- 28 September 2024
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 432
Open AccessA coupled virtual element-interface model for analysis of fracture propagation in polycrystalline composites
- Open Access
- 13 January 2024
- Published by Springer Nature in Computational Mechanics
- Vol. 74 (2) , 379-392
An enhanced corotational Virtual Element Method for large displacements in plane elasticity
An enhanced virtual element formulation for large displacement analyses is presented. Relying on the corotational approach, the nonlinear geometric effects are introduced by assuming nodal large displacements but small strains in the element. The element deformable behavior is analyzed with reference to the local system, corotating with the element during its motion. Then, the large displacement-induced nonlinearity is accounted for through the transformation matrices relating the local and global quantities. At the local level, the Virtual Element Method is adopted, proposing an enhanced procedure for strain interpolation within the element. The reliability of the proposed approach is explored through several benchmark tests by comparing the results with those evaluated by standard virtual elements, finite element formulations, and analytical solutions. The results prove that: (i) the corotational formulation can be efficiently used within the virtual element framework to account for geometric nonlinearity in the presence of large displacements and small strains; (ii) the adoption of enhanced polynomial approximation for the strain field in the virtual element avoids, in many cases, the need for ad-hoc stabilization procedures also in the nonlinear geometric framework.
- 13 January 2024
- Published by Springer Nature in Computational Mechanics
- Vol. 74 (2) , 379-392
Open AccessAn enhanced corotational Virtual Element Method for large displacements in plane elasticity
An enhanced virtual element formulation for large displacement analyses is presented. Relying on the corotational approach, the nonlinear geometric effects are introduced by assuming nodal large displacements but small strains in the element. The element deformable behavior is analyzed with reference to the local system, corotating with the element during its motion. Then, the large displacement-induced nonlinearity is accounted for through the transformation matrices relating the local and global quantities. At the local level, the Virtual Element Method is adopted, proposing an enhanced procedure for strain interpolation within the element. The reliability of the proposed approach is explored through several benchmark tests by comparing the results with those evaluated by standard virtual elements, finite element formulations, and analytical solutions. The results prove that: (i) the corotational formulation can be efficiently used within the virtual element framework to account for geometric nonlinearity in the presence of large displacements and small strains; (ii) the adoption of enhanced polynomial approximation for the strain field in the virtual element avoids, in many cases, the need for ad-hoc stabilization procedures also in the nonlinear geometric framework.
- 29 November 2023
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 419
Corotational force-based beam finite element with rigid joint offsets for 3D framed structures
- 29 November 2023
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 419
Corotational force-based beam finite element with rigid joint offsets for 3D framed structures
- Open Access
- 12 July 2023
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 102
Orthotropic multisurface model with damage for macromechanical analysis of masonry structures
- 12 July 2023
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 102
Open AccessOrthotropic multisurface model with damage for macromechanical analysis of masonry structures
- 1 January 2022
- Published by Begell House Inc. Publishers in International Journal for Multiscale Computational Engineering
- Vol. 20 (6) , 13-42
SHELL-3D MULTISCALE MODELING OF MASONRY VAULTS BASED ON THE TFA PROCEDURE
This paper investigates the response of masonry-curved structural elements with periodic texture by adopting the modeling strategy recently developed by the authors (Addessi et al., 2021). Relying on a multiscale approach, the Mindlin-Reissner shell formulation is assumed at the macroscale and the classical 3D Cauchy continuum is adopted at the microscopic level to model the representative masonry unit cell (UC). The procedure for linking the two scales involves a transformation field analysis (TFA) homogenization technique based on piece-wise uniform distributions of the damaging and frictional mechanisms over the mortar joints. Advantages and limitations of this assumption are explored considering a masonry vault with stack bond texture, that is, assuming a UC made of one linear elastic brick surrounded by one head and one bed joint modeled as nonlinear interfaces. The more appropriate interface discretizations required by the TFA model are identified in relation to the activated deformation modes and the resulting computational effort is evaluated. Hence, an enriched TFA procedure is proposed to limit the computational cost and the time of analysis associated with the denser joint partitions, while still preserving the model accuracy. Finally, the efficiency of the model is investigated at the structural level by analyzing the response of the vault to differential settlements. The comparison between results obtained with the proposed multiscale formulation and those recovered by detailed micromechanical analysis confirms that the TFA approach is a very reliable and effective method for resorting to a fast reduced-order model also for curved geometries.
- 1 January 2022
- Published by Begell House Inc. Publishers in International Journal for Multiscale Computational Engineering
- Vol. 20 (6) , 13-42
SHELL-3D MULTISCALE MODELING OF MASONRY VAULTS BASED ON THE TFA PROCEDURE
This paper investigates the response of masonry-curved structural elements with periodic texture by adopting the modeling strategy recently developed by the authors (Addessi et al., 2021). Relying on a multiscale approach, the Mindlin-Reissner shell formulation is assumed at the macroscale and the classical 3D Cauchy continuum is adopted at the microscopic level to model the representative masonry unit cell (UC). The procedure for linking the two scales involves a transformation field analysis (TFA) homogenization technique based on piece-wise uniform distributions of the damaging and frictional mechanisms over the mortar joints. Advantages and limitations of this assumption are explored considering a masonry vault with stack bond texture, that is, assuming a UC made of one linear elastic brick surrounded by one head and one bed joint modeled as nonlinear interfaces. The more appropriate interface discretizations required by the TFA model are identified in relation to the activated deformation modes and the resulting computational effort is evaluated. Hence, an enriched TFA procedure is proposed to limit the computational cost and the time of analysis associated with the denser joint partitions, while still preserving the model accuracy. Finally, the efficiency of the model is investigated at the structural level by analyzing the response of the vault to differential settlements. The comparison between results obtained with the proposed multiscale formulation and those recovered by detailed micromechanical analysis confirms that the TFA approach is a very reliable and effective method for resorting to a fast reduced-order model also for curved geometries.
- Open Access
- 16 August 2021
- Published by MDPI AG in Geosciences
- Vol. 11 (8) , 343
Nonlinear Dynamic Analysis of a Masonry Arch Bridge Accounting for Damage Evolution
This study investigates the nonlinear dynamic response of the masonry bridge ‘Ponte delle Torri’ in Spoleto, aiming at assessing the seismic performance of the structure and evaluating the occurring damaging mechanisms. A 3D Finite Element (FE) macromechanical procedure implemented in the FE program FEAP is adopted to model the bridge. To reproduce the typical nonlinear microcracking process evolving in masonry material when subjected to external loads, an isotropic damage model is used. This is based on a scalar damage variable introduced in the stress-strain constitutive law and equally degrading all the components of the elastic constitutive operator. A nonlocal integral definition of the damage associated variable, that is the equivalent strain measure governing its evolution, is adopted to overcome the mesh dependency problems of the FE solution typically occurring in the presence of strain softening behavior. Based on the results of a recent study by some of the authors, a single equivalent pier is analyzed, whose geometry and boundary conditions are selected so that its response can provide useful information on the out-of-plane dynamic behavior of the overall bridge. To perform the seismic assessment, a set of recorded accelerograms is properly selected to simulate the seismic history of the Spoleto site. The nonlinear dynamic response of the structure is evaluated and monitored in terms of top displacement time history, evolution of the global damage index, and distribution of the damage variable. First, a set of analyses is performed by imposing the selected ground motions one by one on the initial undamaged configuration for the structure with the aim of emphasizing the damaging effects on its dynamic response. Then, the accelerograms are arranged in sequence to reproduce the seismic history of the site and analyze the influence of accumulated damage on the dynamic amplification of the response. A critical comparison of the bridge response to the sequence of accelerograms and the single records is made, and the interaction between the damaged structure dynamic response and the signal characteristic is highlighted, as well.
- 16 August 2021
- Published by MDPI AG in Geosciences
- Vol. 11 (8) , 343
Open AccessNonlinear Dynamic Analysis of a Masonry Arch Bridge Accounting for Damage Evolution
This study investigates the nonlinear dynamic response of the masonry bridge ‘Ponte delle Torri’ in Spoleto, aiming at assessing the seismic performance of the structure and evaluating the occurring damaging mechanisms. A 3D Finite Element (FE) macromechanical procedure implemented in the FE program FEAP is adopted to model the bridge. To reproduce the typical nonlinear microcracking process evolving in masonry material when subjected to external loads, an isotropic damage model is used. This is based on a scalar damage variable introduced in the stress-strain constitutive law and equally degrading all the components of the elastic constitutive operator. A nonlocal integral definition of the damage associated variable, that is the equivalent strain measure governing its evolution, is adopted to overcome the mesh dependency problems of the FE solution typically occurring in the presence of strain softening behavior. Based on the results of a recent study by some of the authors, a single equivalent pier is analyzed, whose geometry and boundary conditions are selected so that its response can provide useful information on the out-of-plane dynamic behavior of the overall bridge. To perform the seismic assessment, a set of recorded accelerograms is properly selected to simulate the seismic history of the Spoleto site. The nonlinear dynamic response of the structure is evaluated and monitored in terms of top displacement time history, evolution of the global damage index, and distribution of the damage variable. First, a set of analyses is performed by imposing the selected ground motions one by one on the initial undamaged configuration for the structure with the aim of emphasizing the damaging effects on its dynamic response. Then, the accelerograms are arranged in sequence to reproduce the seismic history of the site and analyze the influence of accumulated damage on the dynamic amplification of the response. A critical comparison of the bridge response to the sequence of accelerograms and the single records is made, and the interaction between the damaged structure dynamic response and the signal characteristic is highlighted, as well.