Sayed Youssef Sayed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sayed Youssef Sayed has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Brian C. Olsen
Department of Chemistry, University of Alberta, 11227 Saskatchewan Drive, Edmonton, AB T6G 2G2, Canada
11 shared publications - Jillian M. Buriak
Department of Chemistry, University of Alberta, 11227 Saskatchewan Drive, Edmonton, Alberta T6G 2G2, Canada
11 shared publications - Erik J. Luber
Department of Chemistry, University of Alberta, 11227 Saskatchewan Drive, Edmonton, Alberta T6G 2G2, Canada
7 shared publications - Willem Peter Kalisvaart
Department of Chemistry, University of Alberta, 11227 Saskatchewan Drive, Edmonton, Alberta T6G 2G2, Canada
7 shared publications - Caleb W. Reese
Battery Research and Development
3 shared publications - Hao Wang
Department of Chemistry, University of Alberta, 11227 Saskatchewan Drive, Edmonton, Alberta T6G 2G2, Canada
3 shared publications
Latest Publications
- 5 June 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (11) , 110510
Ex Situ Pre-Lithiation of Silicon-Based Anode Materials
The implementation of silicon (Si) and silicon oxide (SiO x ) anodes for lithium-ion batteries (LIBs) is hindered by first-cycle capacity loss and low Coulombic efficiency due to unstable solid electrolyte interphase (SEI) formation, which consumes lithium and leads to poor cycle life. Here, we present an electrochemical continuous stirred tank reactor (ECSTR) as a platform for ex situ pre-lithiation of Si and SiO x anode materials. Unlike conventional techniques, which suffer from poor lithium distribution and limited scalability, our ECSTR enables uniform, controlled lithiation of Si-based powders through stirring, optimized electrode configurations, and enhanced ion transport. The system, comprising a lithium ingot anode and copper foil cathode, facilitates lithium incorporation in a silicon/silica suspension in electrolyte. Electrochemical characterization, including cyclic voltammetry and impedance spectroscopy, confirms lithiation within 0 V to −2V, with controlled deposition. The process yields reproducible lithiated Si, demonstrating a linear correlation between lithiation capacity and processing time. ECSTR offers a scalable approach for lithiation of various materials, including transition metal oxides and alloy systems, with implications for next-generation non-lithium technologies. Future research integrating real-time monitoring and advanced electrolytes will enhance ECSTR, positioning it as a transformative tool for electrochemical processing across energy storage, catalysis, and material synthesis.
- 5 June 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (11) , 110510
Ex Situ Pre-Lithiation of Silicon-Based Anode Materials
The implementation of silicon (Si) and silicon oxide (SiO x ) anodes for lithium-ion batteries (LIBs) is hindered by first-cycle capacity loss and low Coulombic efficiency due to unstable solid electrolyte interphase (SEI) formation, which consumes lithium and leads to poor cycle life. Here, we present an electrochemical continuous stirred tank reactor (ECSTR) as a platform for ex situ pre-lithiation of Si and SiO x anode materials. Unlike conventional techniques, which suffer from poor lithium distribution and limited scalability, our ECSTR enables uniform, controlled lithiation of Si-based powders through stirring, optimized electrode configurations, and enhanced ion transport. The system, comprising a lithium ingot anode and copper foil cathode, facilitates lithium incorporation in a silicon/silica suspension in electrolyte. Electrochemical characterization, including cyclic voltammetry and impedance spectroscopy, confirms lithiation within 0 V to −2V, with controlled deposition. The process yields reproducible lithiated Si, demonstrating a linear correlation between lithiation capacity and processing time. ECSTR offers a scalable approach for lithiation of various materials, including transition metal oxides and alloy systems, with implications for next-generation non-lithium technologies. Future research integrating real-time monitoring and advanced electrolytes will enhance ECSTR, positioning it as a transformative tool for electrochemical processing across energy storage, catalysis, and material synthesis.
- 22 July 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Enhancing Lithium Metal Anode Stability through Surface Modification and Heat Treatment for 3D Current Collectors
Lithium (Li) metal anodes (LMAs) offer the promise of achieving realistic high-energy-density batteries capable of meeting consumer demands for electric vehicles with a long driving range per charge. However, dendrite formation during Li plating is one of the main challenges that prevents the practical deployment of LMAs. Here, we focus on the Cu current collector (CC)-Li interface and mainly on the modification of the CC surfaces with a lithiophilic coating that has high affinity toward Li deposition. Previous research showed that indium is a potential candidate for preventing lithium dendrite growth. We propose a simple, cost-effective, and scalable solution to enhance the lithiophilicity of Cu current collectors. Indium films were grown electrochemically on Cu three-dimensional CC (3DCC) surfaces and then annealed at 450 °C for 2 h. The unannealed and annealed In coatings both showed a dendrite-free Li morphology and low surface area Li deposits. The electrochemical performances of unannealed and annealed coatings were studied in both symmetric and anode-free cells, all of which exhibited longer cycling stability compared with LMAs utilizing bare Cu 3DCCs.
- 22 July 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Enhancing Lithium Metal Anode Stability through Surface Modification and Heat Treatment for 3D Current Collectors
Lithium (Li) metal anodes (LMAs) offer the promise of achieving realistic high-energy-density batteries capable of meeting consumer demands for electric vehicles with a long driving range per charge. However, dendrite formation during Li plating is one of the main challenges that prevents the practical deployment of LMAs. Here, we focus on the Cu current collector (CC)-Li interface and mainly on the modification of the CC surfaces with a lithiophilic coating that has high affinity toward Li deposition. Previous research showed that indium is a potential candidate for preventing lithium dendrite growth. We propose a simple, cost-effective, and scalable solution to enhance the lithiophilicity of Cu current collectors. Indium films were grown electrochemically on Cu three-dimensional CC (3DCC) surfaces and then annealed at 450 °C for 2 h. The unannealed and annealed In coatings both showed a dendrite-free Li morphology and low surface area Li deposits. The electrochemical performances of unannealed and annealed coatings were studied in both symmetric and anode-free cells, all of which exhibited longer cycling stability compared with LMAs utilizing bare Cu 3DCCs.
- 28 April 2025
- Published by Springer Nature in Journal of Materials Research
- Vol. 40 (8) , 1201-1212
Mechanical performance of lithium metal anodes manufactured using two-dimensional and three-dimensional current collectors
- 28 April 2025
- Published by Springer Nature in Journal of Materials Research
- Vol. 40 (8) , 1201-1212
Mechanical performance of lithium metal anodes manufactured using two-dimensional and three-dimensional current collectors
- 20 February 2025
- Published by SAGE Publications in International Materials Reviews
- Vol. 70 (3) , 139-204
3D Current collectors for Lithium metal anodes: A review on concepts of performance
Lithium metal anodes (LMAs) have the potential to boost cell-level energy densities when coupled with high-capacity cathode materials compared with the ubiquitous graphite electrodes. However, LMAs face several outstanding challenges, including dendritic Li growth, high-volume expansion, and low mechanical strength leading to poor formability for thin and large-format anodes, among others. One approach to address some of these issues is to replace the conventional 2D foils with 3D current collectors (3DCC) which possess high surface areas, open porous structures that are beneficial for increased electrolyte infiltration, faster Li ion transport, and shorter electron transport pathways, all of which can also lower the internal resistance of the cell. This article reviews the theoretical background of the potential influence of 3DCC on the Li plating process, different approaches for manufacturing 3DCCs, and current methodologies for obtaining Li anodes for high-volume manufacturing. For LMAs, the potential benefits of Li-containing 3DCCs are the accommodation of Li volume expansion due to the porous host structure, reduction of local current density due to the higher surface area of the 3D structure, and possibly improvement in the LMA mechanical integrity. Various methods for producing 3DCC structures by the “bottom-up” or the “top-down” methods are described. The synergistic effect of the optimized porous structure (e.g., surface area, pore size & density, tortuosity) of 3DCCs and the “lithiophilic” coatings, providing a wettability of Li, improves cycling performance of LMAs by favoring large-sized and dendrite-free Li deposits. Finally, Li electroplating, evaporation, molten form, and rolling methods have been evaluated for their potential in providing Li metal contained within 3DCCs, each has advantages and shortcomings. Nonetheless, rolling Li on current collectors to produce LMAs is considered the most scalable paradigm due to the room temperature operation conditions and the fact that the wettability of Li is not highly limiting their fabrication.
- 20 February 2025
- Published by SAGE Publications in International Materials Reviews
- Vol. 70 (3) , 139-204
3D Current collectors for Lithium metal anodes: A review on concepts of performance
Lithium metal anodes (LMAs) have the potential to boost cell-level energy densities when coupled with high-capacity cathode materials compared with the ubiquitous graphite electrodes. However, LMAs face several outstanding challenges, including dendritic Li growth, high-volume expansion, and low mechanical strength leading to poor formability for thin and large-format anodes, among others. One approach to address some of these issues is to replace the conventional 2D foils with 3D current collectors (3DCC) which possess high surface areas, open porous structures that are beneficial for increased electrolyte infiltration, faster Li ion transport, and shorter electron transport pathways, all of which can also lower the internal resistance of the cell. This article reviews the theoretical background of the potential influence of 3DCC on the Li plating process, different approaches for manufacturing 3DCCs, and current methodologies for obtaining Li anodes for high-volume manufacturing. For LMAs, the potential benefits of Li-containing 3DCCs are the accommodation of Li volume expansion due to the porous host structure, reduction of local current density due to the higher surface area of the 3D structure, and possibly improvement in the LMA mechanical integrity. Various methods for producing 3DCC structures by the “bottom-up” or the “top-down” methods are described. The synergistic effect of the optimized porous structure (e.g., surface area, pore size & density, tortuosity) of 3DCCs and the “lithiophilic” coatings, providing a wettability of Li, improves cycling performance of LMAs by favoring large-sized and dendrite-free Li deposits. Finally, Li electroplating, evaporation, molten form, and rolling methods have been evaluated for their potential in providing Li metal contained within 3DCCs, each has advantages and shortcomings. Nonetheless, rolling Li on current collectors to produce LMAs is considered the most scalable paradigm due to the room temperature operation conditions and the fact that the wettability of Li is not highly limiting their fabrication.
- Open Access
- 6 February 2025
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 10 (3) , 1099-1106
A Hybrid Intercalation and Conversion Mechanism for Reversible Lithium Storage in Layered Silicane (SiH) with Low Molar Volume Change
- 6 February 2025
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 10 (3) , 1099-1106
Open AccessA Hybrid Intercalation and Conversion Mechanism for Reversible Lithium Storage in Layered Silicane (SiH) with Low Molar Volume Change
- 21 June 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (27) , 35761-35770
Dual-Component Interlayer Enables Uniform Lithium Deposition and Dendrite Suppression for Solid-State Batteries
β-Lithium thiophosphate (LPS) exhibits high Li+ conductivity and has been identified as a promising ceramic electrolyte for safe and high-energy-density all-solid-state batteries. Integrating LPS into solid-state lithium (Li) batteries would enable the use of a Li electrode with the highest deliverable capacity. However, LPS-based batteries operate at a limited current density before short-circuiting, posing a major challenge for the development of application-relevant batteries. In this work, we designed a dual-component interfacial protective layer called LiSn-LiN that forms in situ between the Li electrode and LPS electrolyte. The LiSn component, Li22Sn5, exhibits enhanced Li diffusivity compared with the metallic lithium and facilitates a more uniform lithium deposition across the electrode surface, thus eliminating Li dendrite formation. Meanwhile, the LiN component, Li3N, shows enhanced mechanical stiffness compared with LPS and functions to suppress dendrite penetration. This chemically robust LiSn-LiN interlayer provides a more than doubled deliverable critical current density compared to systems without interfacial protection. Through combined XPS and XAFS analyses, we determined the local structure and the formation kinetics of the key functional Li22Sn5 phase formed via the electrochemical reduction of a Sn3N4 precursor. This work demonstrates an example of the structural-specific design of a protective interlayer with a desired function - dendrite suppression. The structure of a functional protective layer for a given solid-state battery should be tailored based on the given battery configuration and its unique interfacial chemistry.
- 21 June 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (27) , 35761-35770
Dual-Component Interlayer Enables Uniform Lithium Deposition and Dendrite Suppression for Solid-State Batteries
β-Lithium thiophosphate (LPS) exhibits high Li+ conductivity and has been identified as a promising ceramic electrolyte for safe and high-energy-density all-solid-state batteries. Integrating LPS into solid-state lithium (Li) batteries would enable the use of a Li electrode with the highest deliverable capacity. However, LPS-based batteries operate at a limited current density before short-circuiting, posing a major challenge for the development of application-relevant batteries. In this work, we designed a dual-component interfacial protective layer called LiSn-LiN that forms in situ between the Li electrode and LPS electrolyte. The LiSn component, Li22Sn5, exhibits enhanced Li diffusivity compared with the metallic lithium and facilitates a more uniform lithium deposition across the electrode surface, thus eliminating Li dendrite formation. Meanwhile, the LiN component, Li3N, shows enhanced mechanical stiffness compared with LPS and functions to suppress dendrite penetration. This chemically robust LiSn-LiN interlayer provides a more than doubled deliverable critical current density compared to systems without interfacial protection. Through combined XPS and XAFS analyses, we determined the local structure and the formation kinetics of the key functional Li22Sn5 phase formed via the electrochemical reduction of a Sn3N4 precursor. This work demonstrates an example of the structural-specific design of a protective interlayer with a desired function - dendrite suppression. The structure of a functional protective layer for a given solid-state battery should be tailored based on the given battery configuration and its unique interfacial chemistry.
- 1 May 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (5) , 050552
Magnetic Force Dilatometry for Operando Coin Cell Electrochemical Dilation Measurements
Operando characterization of the physical and chemical changes occurring within batteries during electrochemical cycling has become a powerful tool for next generation technology development. In particular, a better understanding of the expansion (dilation) behavior of active materials during charge/discharge is critical for mitigating performance degradation, particularly for high expansion materials like Li or Si. However, current dilatometry devices rely on direct mechanical coupling or line-of-sight measurements with pouch- or custom-cells, which prohibits their use in the most common and accessible research battery format: coin cells. To this end, we propose a novel magnetic force dilatometry (MFD) technique for operando electrochemical dilation measurements. Our custom low-cost dilatometer utilizes magnetic force sensing for contactless expansion measurements via facile replacement of the austenitic spacer with a ferritic spacer within a coin cell. To validate this setup, we demonstrate operando electrochemical dilatometry of a LiNi0.6Mn0.2Co0.2O2 (NMC622) || Li metal full cell in a CR2032 format. Our MFD accurately captures cell expansion/contraction with sensitivities of less than 0.1 μm, and reliability for over hundreds of hours and cycles. This new MFD method is expected to increase the accessibility of electrochemical dilatometry by eliminating the need for pouch cells or other specialized cell expansion measurement configurations.
- 1 May 2024
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 171 (5) , 050552
Magnetic Force Dilatometry for Operando Coin Cell Electrochemical Dilation Measurements
Operando characterization of the physical and chemical changes occurring within batteries during electrochemical cycling has become a powerful tool for next generation technology development. In particular, a better understanding of the expansion (dilation) behavior of active materials during charge/discharge is critical for mitigating performance degradation, particularly for high expansion materials like Li or Si. However, current dilatometry devices rely on direct mechanical coupling or line-of-sight measurements with pouch- or custom-cells, which prohibits their use in the most common and accessible research battery format: coin cells. To this end, we propose a novel magnetic force dilatometry (MFD) technique for operando electrochemical dilation measurements. Our custom low-cost dilatometer utilizes magnetic force sensing for contactless expansion measurements via facile replacement of the austenitic spacer with a ferritic spacer within a coin cell. To validate this setup, we demonstrate operando electrochemical dilatometry of a LiNi0.6Mn0.2Co0.2O2 (NMC622) || Li metal full cell in a CR2032 format. Our MFD accurately captures cell expansion/contraction with sensitivities of less than 0.1 μm, and reliability for over hundreds of hours and cycles. This new MFD method is expected to increase the accessibility of electrochemical dilatometry by eliminating the need for pouch cells or other specialized cell expansion measurement configurations.
- Open Access
- 6 July 2022
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 12 (31) , 20395-20402
Tailor-designed nanowire-structured iron and nickel oxides on platinum catalyst for formic acid electro-oxidation
A FeO x /NiO x /Pt catalyst was recommended for formic acid electro-oxidation; the essential anodic reaction in direct formic acid fuel cells.
- 6 July 2022
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 12 (31) , 20395-20402
Open AccessTailor-designed nanowire-structured iron and nickel oxides on platinum catalyst for formic acid electro-oxidation
A FeO x /NiO x /Pt catalyst was recommended for formic acid electro-oxidation; the essential anodic reaction in direct formic acid fuel cells.
- 6 August 2021
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 13 (32) , 38147-38160
Beyond Thin Films: Clarifying the Impact of c-Li15Si4 Formation in Thin Film, Nanoparticle, and Porous Si Electrodes
The formation of the c-Li15Si4 phase has well-established detrimental effects on the capacity retention of thin film silicon electrodes. However, the role of this crystalline phase with respect to the loss of capacity is somewhat ambiguous in nanoscale morphologies. In this work, three silicon-based morphologies are examined, including planar films, porous planar films, and silicon nanoparticle composite powder electrodes. The cycling conditions are used as the lever to induce, or not induce, the formation of c-Li15Si4 through application of constant-current (CC) or constant-current constant-voltage (CCCV) steps. In this manner, the role of this phase on capacity retention and Coulombic efficiency can be determined with few other convoluting factors such as alteration of the composition or morphology of the silicon electrodes themselves. The results here confirm that the c-Li15Si4 phase increases the rate of capacity decay in planar films but has no major effect on capacity retention in half-cells based on porous silicon films or silicon nanoparticle composite powder electrodes, although this conclusion is nuanced. Besides using a constant-voltage step, formation of the c-Li15Si4 phase is influenced by the dimensions of the Si material and the lithiation cutoff voltage. Porous Si films, which, in this work, comprise primary Si particle sizes that are smaller than those in the preformed Si nanoparticle slurries, do not undergo the formation of c-Li15Si4 at 50 mV, whereas Si nanoparticle slurries are accompanied by the formation of c-Li15Si4 up to 80 mV. The solid-electrolyte interphase (SEI) formed from reaction of the c-Li15Si4 with the carbonate-based electrolyte causes polarization in both nanoparticle and porous film silicon electrodes and lowers the average Coulombic efficiency. A comparison of the cumulative irreversibilities due to SEI formation between different lithiation cutoff voltages in silicon nanoparticle slurry electrodes confirmed the connection between higher SEI buildup and formation of the c-Li15Si4 phase. This work indicates that concerns about the c-Li15Si4 phase in silicon nanoparticles and porous silicon electrodes should mainly focus on the stability of the SEI and a reduction of irreversible electrolyte reactions.
- 6 August 2021
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 13 (32) , 38147-38160
Beyond Thin Films: Clarifying the Impact of c-Li15Si4 Formation in Thin Film, Nanoparticle, and Porous Si Electrodes
The formation of the c-Li15Si4 phase has well-established detrimental effects on the capacity retention of thin film silicon electrodes. However, the role of this crystalline phase with respect to the loss of capacity is somewhat ambiguous in nanoscale morphologies. In this work, three silicon-based morphologies are examined, including planar films, porous planar films, and silicon nanoparticle composite powder electrodes. The cycling conditions are used as the lever to induce, or not induce, the formation of c-Li15Si4 through application of constant-current (CC) or constant-current constant-voltage (CCCV) steps. In this manner, the role of this phase on capacity retention and Coulombic efficiency can be determined with few other convoluting factors such as alteration of the composition or morphology of the silicon electrodes themselves. The results here confirm that the c-Li15Si4 phase increases the rate of capacity decay in planar films but has no major effect on capacity retention in half-cells based on porous silicon films or silicon nanoparticle composite powder electrodes, although this conclusion is nuanced. Besides using a constant-voltage step, formation of the c-Li15Si4 phase is influenced by the dimensions of the Si material and the lithiation cutoff voltage. Porous Si films, which, in this work, comprise primary Si particle sizes that are smaller than those in the preformed Si nanoparticle slurries, do not undergo the formation of c-Li15Si4 at 50 mV, whereas Si nanoparticle slurries are accompanied by the formation of c-Li15Si4 up to 80 mV. The solid-electrolyte interphase (SEI) formed from reaction of the c-Li15Si4 with the carbonate-based electrolyte causes polarization in both nanoparticle and porous film silicon electrodes and lowers the average Coulombic efficiency. A comparison of the cumulative irreversibilities due to SEI formation between different lithiation cutoff voltages in silicon nanoparticle slurry electrodes confirmed the connection between higher SEI buildup and formation of the c-Li15Si4 phase. This work indicates that concerns about the c-Li15Si4 phase in silicon nanoparticles and porous silicon electrodes should mainly focus on the stability of the SEI and a reduction of irreversible electrolyte reactions.
- 10 March 2021
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 21 (6) , 2666-2674
Bipolar Resistive Switching in Junctions of Gallium Oxide and p-type Silicon
In this work, native GaOx is positioned between bulk gallium and degenerately doped p-type silicon (p+-Si) to form Ga/GaOx/SiOx/p+-Si junctions. These junctions show memristive behavior, exhibiting large current–voltage hysteresis. When cycled between −2.5 and 2.5 V, an abrupt insulator–metal transition is observed that is reversible when the polarity is reversed. The ON/OFF ratio between the high and low resistive states in these junctions can reach values on the order of 108 and retain the ON and OFF resistive states for up to 105 s with an endurance exceeding 100 cycles. The presence of a nanoscale layer of gallium oxide is critical to achieving reversible resistive switching by formation and dissolution of the gallium filament across the switching layer.
- 10 March 2021
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 21 (6) , 2666-2674
Bipolar Resistive Switching in Junctions of Gallium Oxide and p-type Silicon
In this work, native GaOx is positioned between bulk gallium and degenerately doped p-type silicon (p+-Si) to form Ga/GaOx/SiOx/p+-Si junctions. These junctions show memristive behavior, exhibiting large current–voltage hysteresis. When cycled between −2.5 and 2.5 V, an abrupt insulator–metal transition is observed that is reversible when the polarity is reversed. The ON/OFF ratio between the high and low resistive states in these junctions can reach values on the order of 108 and retain the ON and OFF resistive states for up to 105 s with an endurance exceeding 100 cycles. The presence of a nanoscale layer of gallium oxide is critical to achieving reversible resistive switching by formation and dissolution of the gallium filament across the switching layer.