Bingfan Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bingfan Li has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Chao Yang
Technology Inspection Center of Shengli Oilfield, SINOPEC, Dongying 257000, China
5 shared publications Jiang Han
School of Vehicle and Energy Yanshan University Qinhuangdao China
4 shared publicationsManping Yang
School of Vehicle and Energy Yanshan University Qinhuangdao China
4 shared publicationsChao Yang
3 shared publications- Shihui Ma
Yanshan University
3 shared publications Ziyuan Guo
School of Vehicles and Energy, Yanshan University, Qinhuangdao, Hebei 066004, P. R. China
3 shared publications
Latest Publications
- Open Access
Pulsed Current Cathodic Protection for Oil and Gas Pipelines: Current Status, Challenges, and Future Trends
Oil and gas pipelines are critical energy infrastructure, and their external corrosion protection affects public safety and economic operation. Pulsed current cathodic protection (PCCP) replaces continuous direct current with a periodically modulated output. This critical narrative review examines its mechanisms, operating parameters, applications, and engineering limitations. The evidence includes laboratory experiments, numerical models, and a limited number of field reports. Some studies report improved potential distribution or lower current demand, but these findings depend on the waveform, soil or electrolyte, coating condition, and comparison criterion. Double-layer charging contributes to the transient response; it does not independently establish sustained off-period protection, energy savings, or an increased protection distance. Pulse-related hydrogen evolution and coating damage also require separate assessment. Particular challenges include heterogeneous and frozen soils, stray-current interference, and interpretation of time-dependent protection potentials. Priorities are matched pulse–DC comparisons, independently validated models, synchronized monitoring, and long-term field measurements. The review identifies the evidence needed to evaluate PCCP for oil and gas pipelines without assuming that results from one installation are transferable to another.
Open AccessPulsed Current Cathodic Protection for Oil and Gas Pipelines: Current Status, Challenges, and Future Trends
Oil and gas pipelines are critical energy infrastructure, and their external corrosion protection affects public safety and economic operation. Pulsed current cathodic protection (PCCP) replaces continuous direct current with a periodically modulated output. This critical narrative review examines its mechanisms, operating parameters, applications, and engineering limitations. The evidence includes laboratory experiments, numerical models, and a limited number of field reports. Some studies report improved potential distribution or lower current demand, but these findings depend on the waveform, soil or electrolyte, coating condition, and comparison criterion. Double-layer charging contributes to the transient response; it does not independently establish sustained off-period protection, energy savings, or an increased protection distance. Pulse-related hydrogen evolution and coating damage also require separate assessment. Particular challenges include heterogeneous and frozen soils, stray-current interference, and interpretation of time-dependent protection potentials. Priorities are matched pulse–DC comparisons, independently validated models, synchronized monitoring, and long-term field measurements. The review identifies the evidence needed to evaluate PCCP for oil and gas pipelines without assuming that results from one installation are transferable to another.
- 19 August 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (35) , 19488-19495
CO2 Hydrate Decomposition and Spatial Temperature Characteristics under Sudden Ambient Temperature Rise
Safety issues in CO2 hydrate storage systems caused by global warming have become a key constraint to the large-scale development and application of this technology. Understanding CO2 hydrate decomposition characteristics and spatial temperature distribution under sudden ambient temperature rise can provide a fundamental basis for controlling decomposition under extreme conditions. This study investigates the CO2 hydrate decomposition characteristics and spatial temperature distribution of different hydrate amounts and ambient temperatures. It was found that the CO2 hydrate decomposition process undergoes a short hydrate stabilization stage, a rapid hydrate decomposition stage, and a slow decomposition stage. In the latter two stages, the relationship between the CO2 hydrate decomposition amount and time follows the equation y = y0 + A × e(R0×x). At the same initial ambient temperatures, y0 and R0 are negatively correlated with the initial hydrate amount, while A is positively correlated with it. An isothermal decomposition stage appears during the rapid decomposition of CO2 hydrate. As the initial hydrate amount increases, the isothermal stage is extended. The duration and temperature of the isothermal phase transition depend on spatial position and ambient temperature. The findings of this work provide significant theoretical support and practical guidance for the safe and stable sequestration of CO2 hydrate.
- 19 August 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (35) , 19488-19495
CO2 Hydrate Decomposition and Spatial Temperature Characteristics under Sudden Ambient Temperature Rise
Safety issues in CO2 hydrate storage systems caused by global warming have become a key constraint to the large-scale development and application of this technology. Understanding CO2 hydrate decomposition characteristics and spatial temperature distribution under sudden ambient temperature rise can provide a fundamental basis for controlling decomposition under extreme conditions. This study investigates the CO2 hydrate decomposition characteristics and spatial temperature distribution of different hydrate amounts and ambient temperatures. It was found that the CO2 hydrate decomposition process undergoes a short hydrate stabilization stage, a rapid hydrate decomposition stage, and a slow decomposition stage. In the latter two stages, the relationship between the CO2 hydrate decomposition amount and time follows the equation y = y0 + A × e(R0×x). At the same initial ambient temperatures, y0 and R0 are negatively correlated with the initial hydrate amount, while A is positively correlated with it. An isothermal decomposition stage appears during the rapid decomposition of CO2 hydrate. As the initial hydrate amount increases, the isothermal stage is extended. The duration and temperature of the isothermal phase transition depend on spatial position and ambient temperature. The findings of this work provide significant theoretical support and practical guidance for the safe and stable sequestration of CO2 hydrate.
- 2 February 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (6) , 2921-2930
The Synergistic Effect of Saturated Na 2 SO 4 and SDS on Methane Hydrate Formation
- 2 February 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (6) , 2921-2930
The Synergistic Effect of Saturated Na 2 SO 4 and SDS on Methane Hydrate Formation
- 8 June 2025
- Published by Wiley in Materials and Corrosion
- Vol. 76 (11) , 1584-1607
Application and Challenges of Self‐Healing Polymer Coatings in Metal Corrosion Protection
Self‐healing anticorrosion coatings have the potential to significantly reduce the losses caused by metal corrosion. This paper reviews the types of self‐healing coatings, focusing on the repair mechanisms of different types of self‐healing anticorrosion coatings. It also explores the advantages and disadvantages of different types of self‐healing materials. Firstly, the hazards of metal corrosion and the importance of self‐healing coatings in the industrial field are introduced. Secondly, the triggering conditions of reversible dynamic bonding and shape memory polymers are summarized, including thermal triggering, light‐induced, water triggering, and so on. Thirdly, the characteristics and repair mechanisms of intrinsic self‐healing coatings are described in detail. Subsequently, the preparation methods and mechanisms of the extrinsic self‐healing anticorrosion coatings have been analyzed on the basis of different triggering conditions. In addition, due to the many shortcomings of a single repair mechanism, this article also explores the repair mechanism of multifunctional self‐healing coatings. Finally, the current research status was summarized, and this paper proposes the future development direction of self‐healing coatings in practical engineering applications.
- 8 June 2025
- Published by Wiley in Materials and Corrosion
- Vol. 76 (11) , 1584-1607
Application and Challenges of Self‐Healing Polymer Coatings in Metal Corrosion Protection
Self‐healing anticorrosion coatings have the potential to significantly reduce the losses caused by metal corrosion. This paper reviews the types of self‐healing coatings, focusing on the repair mechanisms of different types of self‐healing anticorrosion coatings. It also explores the advantages and disadvantages of different types of self‐healing materials. Firstly, the hazards of metal corrosion and the importance of self‐healing coatings in the industrial field are introduced. Secondly, the triggering conditions of reversible dynamic bonding and shape memory polymers are summarized, including thermal triggering, light‐induced, water triggering, and so on. Thirdly, the characteristics and repair mechanisms of intrinsic self‐healing coatings are described in detail. Subsequently, the preparation methods and mechanisms of the extrinsic self‐healing anticorrosion coatings have been analyzed on the basis of different triggering conditions. In addition, due to the many shortcomings of a single repair mechanism, this article also explores the repair mechanism of multifunctional self‐healing coatings. Finally, the current research status was summarized, and this paper proposes the future development direction of self‐healing coatings in practical engineering applications.
- 10 October 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (21) , 20928-20938
Identification of CO2 Leakage in an Active CO2-EOR Field, Songliao Basin, China
- 10 October 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (21) , 20928-20938
Identification of CO2 Leakage in an Active CO2-EOR Field, Songliao Basin, China
- Open Access
Study on Wax Deposition Process of Crude Oil System under Shear Flow Field Conditions
This paper adopted numerical simulation based on the MD method to research the effect of different shear rates and wax contents on wax deposition focused on crude oil. The findings indicated that under shear flow conditions, there were primarily four steps during deposition. Diffusion was the initial stage when wax diffused onto the metal surface. In the second stage, wax adsorbed onto a metal surface aligned itself parallel to the surface via Brownian motion, generating two different kinds of deposits. Subsequently, agglomerates were formed between the adsorbed deposits and the wax as a result of molecular interactions and bridging effects. Furthermore, the second and third deposited layers gradually showed peeling off and sliding under shear force. The wax deposition process was comparable for crude oil systems with varying shear rates and wax concentrations, and the deposited layer’s thickness on the metal surface was constant. The first, second, and third deposits were mainly adsorbed at 0.122 nm, 0.532 nm, and 1.004 nm away from the Fe surface, and the interaction energy between crude oil molecules and the Fe surface was mainly vdW force. The contact between Fe and wax progressively increased as the shear rate and wax content rose, promoting the wax adsorption on the metal surface and causing more of the wax to congregate in the deposited wax. The findings of the research can theoretically help a more thorough comprehension of the wax deposition.
Open AccessStudy on Wax Deposition Process of Crude Oil System under Shear Flow Field Conditions
This paper adopted numerical simulation based on the MD method to research the effect of different shear rates and wax contents on wax deposition focused on crude oil. The findings indicated that under shear flow conditions, there were primarily four steps during deposition. Diffusion was the initial stage when wax diffused onto the metal surface. In the second stage, wax adsorbed onto a metal surface aligned itself parallel to the surface via Brownian motion, generating two different kinds of deposits. Subsequently, agglomerates were formed between the adsorbed deposits and the wax as a result of molecular interactions and bridging effects. Furthermore, the second and third deposited layers gradually showed peeling off and sliding under shear force. The wax deposition process was comparable for crude oil systems with varying shear rates and wax concentrations, and the deposited layer’s thickness on the metal surface was constant. The first, second, and third deposits were mainly adsorbed at 0.122 nm, 0.532 nm, and 1.004 nm away from the Fe surface, and the interaction energy between crude oil molecules and the Fe surface was mainly vdW force. The contact between Fe and wax progressively increased as the shear rate and wax content rose, promoting the wax adsorption on the metal surface and causing more of the wax to congregate in the deposited wax. The findings of the research can theoretically help a more thorough comprehension of the wax deposition.
- Open Access
Research on the Effect of Static Pressure on the Rheological Properties of Waxy Crude Oil
In this paper, with the application of a MARS 60 high-pressure rheometer, experimental tests are conducted on Shengli crude oil to test its gel point, viscosity and thixotropy under different static pressures. Consequently, the effect of static pressure on the rheological parameters of waxy crude oil is revealed. It is proven that with the increase in the static pressure, the gel point of Shengli crude oil increases linearly, and the viscosity also gradually increases. The power law equation is employed to describe the relationship between the apparent viscosity and shear rate of Shengli crude oil under different static pressures. With the increase in the static pressure, the consistency coefficient (K) increases linearly, and the rheological index (n) decreases linearly. The relationship between the viscosity of Shengli crude oil and the static pressure and shear rate can be obtained. The Cross thixotropic model is used to describe the thixotropic curve of Shengli crude oil under different static pressures. With the increase in the static pressure, the thixotropic coefficient of consistency (ΔK) and the structure fracture constant (b) increase linearly. This is because a high pressure results in high structure strength and strong non-Newton rheological behavior in gelled crude oil and also causes remarkable structure fracture in crude oil. The results in this paper can provide an important theoretical basis for crude oil production and transportation.
Open AccessResearch on the Effect of Static Pressure on the Rheological Properties of Waxy Crude Oil
In this paper, with the application of a MARS 60 high-pressure rheometer, experimental tests are conducted on Shengli crude oil to test its gel point, viscosity and thixotropy under different static pressures. Consequently, the effect of static pressure on the rheological parameters of waxy crude oil is revealed. It is proven that with the increase in the static pressure, the gel point of Shengli crude oil increases linearly, and the viscosity also gradually increases. The power law equation is employed to describe the relationship between the apparent viscosity and shear rate of Shengli crude oil under different static pressures. With the increase in the static pressure, the consistency coefficient (K) increases linearly, and the rheological index (n) decreases linearly. The relationship between the viscosity of Shengli crude oil and the static pressure and shear rate can be obtained. The Cross thixotropic model is used to describe the thixotropic curve of Shengli crude oil under different static pressures. With the increase in the static pressure, the thixotropic coefficient of consistency (ΔK) and the structure fracture constant (b) increase linearly. This is because a high pressure results in high structure strength and strong non-Newton rheological behavior in gelled crude oil and also causes remarkable structure fracture in crude oil. The results in this paper can provide an important theoretical basis for crude oil production and transportation.
- Open Access
- 9 August 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (33) , 35256-35274
Research Status and Challenges of Mechanism, Characterization, Performance Evaluation, and Type of Nano-Pour Point Depressants in Waxy Crude Oil
Nano-Pour point depressants have great potential to improve the low-temperature fluidity of waxy crude oil. This Review reviews the recent research progress of nano-pour point depressants in the field of crude oil pour point reduction. The effect and mechanism of nanocomposite pour point depressants are analyzed; the preparation, modification, and microstructure characterization of nanocomposite pour point depressants are introduced; the three main types of nano-pour point depressants, namely, silicon-based, carbon-based, and magnetic metal-based, are introduced; the results of the current research are outlined; and the challenges of the current research and possible directions of future research are also pointed out. The in-depth analysis of nano-pour point depressants and their potential to improve the low-temperature fluidity of waxy crude oil are reviewed in order to thoroughly analyze the mechanism of nano-pour point depressants and to prepare nano-pour point depressants that are more suitable for reducing crude oil coagulation.
- 9 August 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (33) , 35256-35274
Open AccessResearch Status and Challenges of Mechanism, Characterization, Performance Evaluation, and Type of Nano-Pour Point Depressants in Waxy Crude Oil
Nano-Pour point depressants have great potential to improve the low-temperature fluidity of waxy crude oil. This Review reviews the recent research progress of nano-pour point depressants in the field of crude oil pour point reduction. The effect and mechanism of nanocomposite pour point depressants are analyzed; the preparation, modification, and microstructure characterization of nanocomposite pour point depressants are introduced; the three main types of nano-pour point depressants, namely, silicon-based, carbon-based, and magnetic metal-based, are introduced; the results of the current research are outlined; and the challenges of the current research and possible directions of future research are also pointed out. The in-depth analysis of nano-pour point depressants and their potential to improve the low-temperature fluidity of waxy crude oil are reviewed in order to thoroughly analyze the mechanism of nano-pour point depressants and to prepare nano-pour point depressants that are more suitable for reducing crude oil coagulation.
- 20 April 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (9) , 7480-7509
Research Status and Outlook of Mechanism, Characterization, Performance Evaluation, and Type of Pour Point Depressants in Waxy Crude Oil: A Review
- 20 April 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (9) , 7480-7509
Research Status and Outlook of Mechanism, Characterization, Performance Evaluation, and Type of Pour Point Depressants in Waxy Crude Oil: A Review